I have to change ISP, as mine is closing down , and the new ISP will be sending a N router - which may have 5Gh - so I'm thinking of replacng a "G" AP with the WAG320N and use the 5Ghz range. The WAG320N will be used with a USB Music harddrive and a TV and PVR connected to it - so my music will be direct to the DLNA devices - and also provide any devices with a 5Ghz signal
View 9 RepliesI'm using a router WAG320N in my home but now i need to expand my lan with another ports and wireless coverage.In a wired point (connect directly to the router) i need 3 ehternet ports and a repetear of a wireless signal.The optimal solution woulb be a switch gigabit with an integrated acces point, but I understand that there is no such thing...So going to buyng the switch SE2500 and the AP WAP610N... but then I realized the existence of the bridge WES610N!But the information on the linksys italian site is not enough and the relative page does not works... i need to now if this object can take a wired lan replicate it in 3 ports and expand the wireless network of my router.
View 5 Replies View RelatedI have WAG320N. I attached External HDD to Router's USB.I don't know how to access to HDD and other users also..(not via internet)
View 1 Replies View RelatedI disabled Remote Access under the Administration tab but I still can access my router management from the internet by typing in my routers gateway address. In fact I did the opposite of all that is described here. I already did a soft- and hardware reset. How can I block Remote Access forever?
View 4 Replies View RelatedI recently purchased a WAG320N router and have issues with access restrictions. Internet is shut down regardless of the time set with the policy or policies. I am using firmware version V1.00.12. Tried rebooting router, restoring factory defaults & restarting IMAC to no avail. Timezone checked and OK.
View 5 Replies View RelatedI access my home computers via teamviewer or logmein. My router is a Wag320n
Sometimes my internet connection is lost and if I'm home, I just reset it and the internet is on again.
But when I am away and the internet connection is lost, I can not access my computer. If only I could reset it, I would be able to access the computers I am trying to find a solution to do this.
Practically when the internet connection is lost, the modem does not get an IP from the ISP right? And when this IP is not assigned, there is no way of connecting to the router itself right? Is there a way of pinging or resetting or accessing a modem that is connected to he phone line? I think it is impossible. Or maybe it is possible via some MAC address search or sniffer or I don't know.
Another option would be to somehow have the modem reset, let's say every hour automatically so that the max time I would not be able to accss my computers remotely would be 1 hour.
I have a flat that is about 500Sq meters in size and multiple rooms. I am looking to setup one WAG320N in the library with the ADSL connection and setup wireless. Can I then wireless a WAP610 or another AP in the living room and in the dinner room and in one bedroom and set it up with the same Wireless network so they can move seamlessly through the flat? Can they act in repeater mode? Which Modem Gateway and Access Point or Repeater can do it.
View 2 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI have set up several Website Blocking by URL Address & Website Blocking by Keyword that work as expected but the router seems unstable when they are in use and often reboots at random occasions.For example, last 2 crashes happened like this:
opened a website that wouldn't load because it contained one of the keywordsopened a new tab to go to http://192.168.1.1as soon as I hit ENTER router rebootedanother occasion:
Went to Access Restrictions and Disabled an Internet Access Policy (did not close the tab).Opened a new tab and went about my businesslater went back (to the already open router tab) to Enable the Internet Access Policyclicked Save Settingsentered router password againclicked OK and it crashed (rebooted)
WAG320N Firmware Version:V1.00.12
Firefox 5
I have had trouble setting my WAG120N as router.
I am connected to internet via a cable modem, via the LAN cable, I connect cable modem to WAG120N that I want to use as an wireless access point only. And I have got 2 PC, 1 runs on XP, the other on runs on Windows 7. My XP would have no trouble to connect to wireless, but the Win7 can only connect to wireless network, but no internet. When I try the troubleshooting from Win 7, it says, DNS server isnt responding The setting I am using at the moment is Bridged mode only, without entering any values of DNS, IP, etc Is there any setting that work for both OS?
I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.
View 6 Replies View Relatedmy device can connect to the wireless network. When i tried to setup the network again it says that no WLAN network found. I have not change any of the setting in the modem it just can't find any WLAN network. I have tried reseting the modem but still no network found.
View 4 Replies View RelatedI have had a wag320n for a while and ever since I bought it, The wireless stops functioning after a day or 2, if I save the settings and then restore the settings (even after it has stopped working) then it works again for a day or to then I have to repeat the process.While it was annoying most of my PC's were wired so it wasn't a major issue but in my new place I am mostly wireless so I am well over it already.
View 2 Replies View RelatedI have a small home network using a Linksys WAG320N which acts as the modem (to connect to BT using PPPoA for ADSL) and provides 4 wired 100Mbs network connections along with a wireless N connections. I use WPA2 (personal) to secure the network and have a white list for allowed wireless devices. Everything works fine.In another part of the house (where I can get a good wireless signal) we have the main TV in the house. Here I have a SKY HD box and a small media player. What I would like to do is connect these two devices to the network and running a network cable is not practical, so I thought I would setup a wireless bridge.I tried a TP-Link bridge borrowed from a friend by this failed to work. I now know this to be because the WAG320N does not support WDS.Will a Linksys WES610N connect to my WAG320N to provide me with what I want?
View 1 Replies View RelatedMy wag320N was working fine for a few months but recently has started to drop out. The wireless signal is strong and is used to stream HD movies to a HTPC and also to a media player in different parts of the house. The stream works fine for a while then every 2-5 minutes or so the signal drops to nothing for about 45 seconds, then comes back up to normal and then this repeats for the entire movie.
View 2 Replies View RelatedI've had enough of BT's shoddy Home Hub router dying whenever I transfer large files over wifi so I want to go back to a trusty Linksys and I'm looking at the WAG320N.
I've got a family member who is convinced wifi is harmful, so to avoid an argument I've agreed to switch it off at night. My last Linksys let me do this via a custom firmware, but the WAG320N isn't a Linux based model. So, my question is: can I set wifi to switch itself off at night from e.g. 11pm until 8am? Preferably this will be an actual switch-off rather than just preventing access via certain wifi devices.
If it can't do it, any alternative Linksys ADSL2+ modem that can?
I recently replaced my old router with wag320n and I'm concerned about the wireless transfer which is really poor. 2,5Mbps is maximum I get which is really disappointing as I share lots of things on my network and could really use some better data transfer. Distance to the router is irrelevant, 5 metres or 0,5 metres - all the same/I tried different frequencies, 20 and 40 mhz bandwidth, no result as well.I know that 150mbps is just theoretical but 20mbps is 13% of the N standard, that's not what I expected from linksys.Firmware version is V1.00.12, all the advanced wireless settings are set to default. I tried different values but they make no difference at all.
View 6 Replies View RelatedI have recently purchased a WAG320N. Hard wired to my desktop has a reasonable speed. Wireless to any of our lap tops and it is very slow. Do I need to adjust any factory settings to improve the wireless speed ?
View 1 Replies View RelatedI have a wag320n that works good on ground level, but the modem is standing in mt technical closet where i think is a lot of 'interference' that degrades the wireless signal. So upstairs i am alos working with a wireless...kind of tv server that has a very poor signal from my wag320n. I want to boost that up a bit by using a wap54g on the attic. But i cannot get it to work....it only gives a a wireless signal from my wag320n.
View 1 Replies View Relatedmy modem/router WAG320N works ok but wireless client can't see wired and vice versa. they are in the same network (192.168.0. ), using the same 255.255.255.0 mask, same workgroup and yes firewalls allowing all packets in and out. IP addresses are form DHCP.
internet sharing works ok, but when im trying to play any game on LAN wireless clients can see them self but not the wired one. when im trying to ping wireless client from a wired machine it doesn't work either.
what's intresting in a DHCP reservation or ARP table (in router setup) i can see both wired and wireless clients. but still they can not see each other.
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
I have had a WAG320N running problem free for approx 2 months, in that time I've upgraded the firmware 1.00.12 with no issues and has run fine for a month after upgrade. I have 3 laptops connected wirelessly and 2 pc's running wired (through homeplug system) plus TV, PS3 and ipods, all have run without issues.
All of a sudden 2 days ago all wireless connectivity stopped? SSID is still broadcasting and viewable but I can no longer connect with any computer or device. Wired connectivity is working fine.
I've checked security settings, turned off encryption, reset factory defaults, re-downloaded latest firmware and reflashed with no luck. As I said wirless stopped working all of a sudden with no changes to settings.
I live in a block of flats I decided to buy a proper router on 5GHz. I can see at least 12 wireless networks and all of them on 2.4GHz(mostly BT HomeHubs or other UK ISP wireless boxes). I study CCNA and our teachers recommend cisco routers(linksys) as the best ones. I bought a WAG320N as the best one I could find in the UK market for a fair price. The problem is, that I have less signal on 5GHz than on 2.4GHz. I have maximum 50% of signal on 5GHz and speed is usually below 802.11g, means below 64Mbps! I can't believe it. When I change it to 2.4GHz the signal has up to 80% like my old router TP-Link. The speed is mostly up to 65Mbps, means terrible. I have seen lots of topics about this particular router but I couldn't believe that Cisco sell such awful and unreliable products like this router. I have tried to change the channels on 5 and 2.4GHz but it's always the same, poor speed and low signal. My wireless card is Intel WifiLink 6200 Advanced -N and operating systems Windows 7 and Sabayon linux. I have a laptop and it is cca 6 metres from the router and there are 2 walls. The router is still under warranty so I won't hesitate to return it back to PCWorld.
View 9 Replies View RelatedI have d-link wireless router which is connected to the internet, also I have Linksys (WAG160Nv2) which i want to use it as access point by link it to D-link router using ethernet cable in order to use the wireless internet. D-link router settings shown below
I changed the settings of linksys router as shown below
I have two routers and was wondering if it is possible to use one as a router and one as an Access point, do you know if this is possible and how do i go about configuring this?
Currently my wagN160N v2 is the one that my dsl is connected to, but how do i go about sharing this to my other router and making the WAG160n v1 the access point?
i have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
View 1 Replies View Relatedi have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
My devices will connect to 192.168.0.0 network
Is it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies View RelatedI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View Relatedi'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
View 3 Replies View RelatedI have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies View Relatedhow to configure or set up VPN on WAG320N?
View 3 Replies View RelatedI have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.