I have recently purchased a WAG320N. Hard wired to my desktop has a reasonable speed. Wireless to any of our lap tops and it is very slow. Do I need to adjust any factory settings to improve the wireless speed ?
View 1 RepliesThis WAG320N Router can get really slow after a while use which is really frustrating for me since I am a gamer. Power cycling it SOMETIMES does the trick but it will still get slow. It has been slow just now and over here it is midnight so the internet peak should be down and my internet should be faster but its now.
View 2 Replies View RelatedTransferring a file between a wired Win 7 machine and a wireless Snow Leopard mac seems to top out at 32Mbps.I've seen over 60Mbps on this laptop using N networks before, and when I wire the laptop I get a more respectable 240Mbps (presumably maxing out the server's disk I/O rate), so I'd say the issue is the router.
Things I have already tried:updating the firmware to 1.00.125Ghz modeFinding the least crowded 2.4Ghz channelswide channelsSetting network mode to N-onlySetting the transmission rate to 108Mbpschanging the beacon interval to 50, the frag threshold to 2201 and the RTS threshold to 2202
I was using Billion ADSL 2+ modem since last 6 years. It was working well but I need Wireless LAN N speed connection and I bought Linksys WAG320N.After configuring the modem my download speed has come doen't to less than 1Mb/s. When I connect to my old Billion I am getting 16Mb/s. [code]
View 2 Replies View RelatedI have the above router, but I have noticed that the USB Transfer speed is very poor. I have a WD External HD plugged into the router and id i transfer filed from my server which is hardwired to the router I only get a transfer speed of about 2.5MB/s.
For a USB device I was kind of thinking I would be getting a minumm of atleast 50-60MB/s.
I have a home network running on a Linksys WAG320n and i have attached to it a WD MyBookLive (w Gigabit Ethernet). I am connected on the network via my Dell with a Intel(R) WiFi Link 5300 AGN. I am not able though to connect on N range. I have installed the latest drivers from Intel but nothing changed. When i try to copy a file from my computer to the WD Network drive the transfer rates are very slow. I get Max 2MB/s - 3MB/s while if i connect my computer with a wire the speed goes up by 3-4 times more.
View 5 Replies View Relatedmy device can connect to the wireless network. When i tried to setup the network again it says that no WLAN network found. I have not change any of the setting in the modem it just can't find any WLAN network. I have tried reseting the modem but still no network found.
View 4 Replies View RelatedI have had a wag320n for a while and ever since I bought it, The wireless stops functioning after a day or 2, if I save the settings and then restore the settings (even after it has stopped working) then it works again for a day or to then I have to repeat the process.While it was annoying most of my PC's were wired so it wasn't a major issue but in my new place I am mostly wireless so I am well over it already.
View 2 Replies View RelatedI have a small home network using a Linksys WAG320N which acts as the modem (to connect to BT using PPPoA for ADSL) and provides 4 wired 100Mbs network connections along with a wireless N connections. I use WPA2 (personal) to secure the network and have a white list for allowed wireless devices. Everything works fine.In another part of the house (where I can get a good wireless signal) we have the main TV in the house. Here I have a SKY HD box and a small media player. What I would like to do is connect these two devices to the network and running a network cable is not practical, so I thought I would setup a wireless bridge.I tried a TP-Link bridge borrowed from a friend by this failed to work. I now know this to be because the WAG320N does not support WDS.Will a Linksys WES610N connect to my WAG320N to provide me with what I want?
View 1 Replies View RelatedMy wag320N was working fine for a few months but recently has started to drop out. The wireless signal is strong and is used to stream HD movies to a HTPC and also to a media player in different parts of the house. The stream works fine for a while then every 2-5 minutes or so the signal drops to nothing for about 45 seconds, then comes back up to normal and then this repeats for the entire movie.
View 2 Replies View RelatedI have to change ISP, as mine is closing down , and the new ISP will be sending a N router - which may have 5Gh - so I'm thinking of replacng a "G" AP with the WAG320N and use the 5Ghz range. The WAG320N will be used with a USB Music harddrive and a TV and PVR connected to it - so my music will be direct to the DLNA devices - and also provide any devices with a 5Ghz signal
View 9 Replies View RelatedI've had enough of BT's shoddy Home Hub router dying whenever I transfer large files over wifi so I want to go back to a trusty Linksys and I'm looking at the WAG320N.
I've got a family member who is convinced wifi is harmful, so to avoid an argument I've agreed to switch it off at night. My last Linksys let me do this via a custom firmware, but the WAG320N isn't a Linux based model. So, my question is: can I set wifi to switch itself off at night from e.g. 11pm until 8am? Preferably this will be an actual switch-off rather than just preventing access via certain wifi devices.
If it can't do it, any alternative Linksys ADSL2+ modem that can?
I recently replaced my old router with wag320n and I'm concerned about the wireless transfer which is really poor. 2,5Mbps is maximum I get which is really disappointing as I share lots of things on my network and could really use some better data transfer. Distance to the router is irrelevant, 5 metres or 0,5 metres - all the same/I tried different frequencies, 20 and 40 mhz bandwidth, no result as well.I know that 150mbps is just theoretical but 20mbps is 13% of the N standard, that's not what I expected from linksys.Firmware version is V1.00.12, all the advanced wireless settings are set to default. I tried different values but they make no difference at all.
View 6 Replies View RelatedLast year I was working with Vista laptop and pc , there were no wireless problems with the WAG54G2-EW. Now I have 2 laptops, working on windows 7. But they cannot go to wirless mode, only connected with a cable I can go to the internet. I have downloaded the last firmware.When I tried Windows help the conclusion is : your router cannot be configurated for Windows7
View 2 Replies View RelatedI have a wag320n that works good on ground level, but the modem is standing in mt technical closet where i think is a lot of 'interference' that degrades the wireless signal. So upstairs i am alos working with a wireless...kind of tv server that has a very poor signal from my wag320n. I want to boost that up a bit by using a wap54g on the attic. But i cannot get it to work....it only gives a a wireless signal from my wag320n.
View 1 Replies View Relatedmy modem/router WAG320N works ok but wireless client can't see wired and vice versa. they are in the same network (192.168.0. ), using the same 255.255.255.0 mask, same workgroup and yes firewalls allowing all packets in and out. IP addresses are form DHCP.
internet sharing works ok, but when im trying to play any game on LAN wireless clients can see them self but not the wired one. when im trying to ping wireless client from a wired machine it doesn't work either.
what's intresting in a DHCP reservation or ARP table (in router setup) i can see both wired and wireless clients. but still they can not see each other.
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
I have had a WAG320N running problem free for approx 2 months, in that time I've upgraded the firmware 1.00.12 with no issues and has run fine for a month after upgrade. I have 3 laptops connected wirelessly and 2 pc's running wired (through homeplug system) plus TV, PS3 and ipods, all have run without issues.
All of a sudden 2 days ago all wireless connectivity stopped? SSID is still broadcasting and viewable but I can no longer connect with any computer or device. Wired connectivity is working fine.
I've checked security settings, turned off encryption, reset factory defaults, re-downloaded latest firmware and reflashed with no luck. As I said wirless stopped working all of a sudden with no changes to settings.
I live in a block of flats I decided to buy a proper router on 5GHz. I can see at least 12 wireless networks and all of them on 2.4GHz(mostly BT HomeHubs or other UK ISP wireless boxes). I study CCNA and our teachers recommend cisco routers(linksys) as the best ones. I bought a WAG320N as the best one I could find in the UK market for a fair price. The problem is, that I have less signal on 5GHz than on 2.4GHz. I have maximum 50% of signal on 5GHz and speed is usually below 802.11g, means below 64Mbps! I can't believe it. When I change it to 2.4GHz the signal has up to 80% like my old router TP-Link. The speed is mostly up to 65Mbps, means terrible. I have seen lots of topics about this particular router but I couldn't believe that Cisco sell such awful and unreliable products like this router. I have tried to change the channels on 5 and 2.4GHz but it's always the same, poor speed and low signal. My wireless card is Intel WifiLink 6200 Advanced -N and operating systems Windows 7 and Sabayon linux. I have a laptop and it is cca 6 metres from the router and there are 2 walls. The router is still under warranty so I won't hesitate to return it back to PCWorld.
View 9 Replies View RelatedI have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies View Relatedhow to configure or set up VPN on WAG320N?
View 3 Replies View RelatedI have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.
How to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.
RFC2684 Bridged
LLC/SNAP
g.dmt or ADSL2+
VPI 0
VCI 100
But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP.
I'm trying to play some online games and my WAG320N does not forward ports, upnp does not function and to top it off DMZ wont even work (not a software firewall issue either). I have the latest firmware (and honestly the stock firmware is terrible).
Am I out of luck or is there something I can do to fix this? I sure as hell will be steering clear of linksys products after this.
i need to downgrade my WAG320N and don't find old firmware 1.00.08 AnnexA
View 9 Replies View RelatedI have the WAG320N. I know if my router is updated to fix the bug of the WPS?There is an update? Which is the date scheduled for release? The vulnerability of my network has been compromised yesterday because of this bug, so either the update is released soon or I'll have to switch to another product of some companies more serious
View 3 Replies View RelatedI have only purchased this modem a few days ago (upgraded from a working Netgear DGN2000 for Gigabit).... it's solid most the time except for once a day when it needs to be reset.
One morning I accessed a single website, only to find the next wouldn't come up. (approx 7:30am) Lastnight the net was working fine at 11:30pm.... Thismorning I woke up, checked my download manager to find that at 2:30am all queued downloads failed, so the ADSL dropped sometime inbetween then.
The LAN and Wifi still work fine, when I go into the settings and click "reconnect" nothing happens. I need to turn the modem off for a min before it works ok. There is no newer firmware as of yet to try.
I do not have a "storage" tab in my setup screen. I have Setup, Security, Wireless, etc. According to its manual there must be a Storage tab between security and wireless. Mine doesn't have it. USB drive is connected and I see "mywag320n" on the network but I can't access it because it requires login and password (which I guess I must set up from Storage tab )
View 8 Replies View RelatedI connected my Western Digital Studio II 2TB external harddrive which is formatted NTFS. I can access the drive and read it. But I can't write it. It says I do not have rights. I tried to get to be the owner of the device but it gave some kind of error.
View 2 Replies View RelatedI need to configure my modem router wag320n let pass the magic packet to turn on my computer from the internet. I've already opened the door 7 to the computer ip but does not work. The bios and the OS are perfectly configured.
View 8 Replies View RelatedI have recently bought a WAG320N modem Gigabite router to substitute the modem router supplied by the internet service provider (in theory less performant).
Formerly I have a wireless router Zyxel (MOD. P660HW-D1). The main computer is wired (connected trough ethernet), I have also a NAS device (WD mybook world 1TB with Twonky as server) wired and a third wired connection for the above mentioned PLK 300. The PLK 300 (4 Inputs and one output) is used to connect a TV (Sony BRAVIA) a Bluray (SONY) a PS3 (Sony) and a multimedia HD (DVICO). All this was working properly. I have internet access from TV, PS3,... I was able to run videos, photos,... stored in the NAS from TV,....
I decided to change for improving the transfer speed and to allow a better wireless connection (I have initially coverage problems, but because I only use the wireless rarely...).Initially I bought a Linksys E 3000 (I thought it was possible to connect it directly to internet and not trough a modem. I asked to several people and in several shops but no one told me this was not possible). That was my first failure: I would like to suggest the liknsys people to clearly explain this on the product sheet to avoid that not very well informed people like me commit the same error.
Then I chaged the E3000 by the WAG320N. I connect the new modem-router like the former (Zyxel). No room for big errors, just the power, DSL line and ethernet cables. It works for the PC and the NAS but the PLC (PLK300) do not appears to work. Several tries later (including plugin the PLK on the line 1 input of the router it is shown on the network map but do not work. I do not have access to the internet nor to the NAS contents form TV,....
I go back to the former router and everything works again in the simplest way (I have internet access form TV,...) except the Twonky access to the NAS from TV ¿?. I do not know exactly what I have changed,...)
How do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.
View 8 Replies View Relatedhow to make in WAG320N second PVC for IP TV. It looks like unsupportable feature May be next firmware will include it? Or better to change the device? What Linksys with ADSL are support IP TV?
View 3 Replies View Related