I have two routers and was wondering if it is possible to use one as a router and one as an Access point, do you know if this is possible and how do i go about configuring this?
Currently my wagN160N v2 is the one that my dsl is connected to, but how do i go about sharing this to my other router and making the WAG160n v1 the access point?
I hard reset the router WAG160N and i can't access it on 192.168.1.1, i can connect to the wireless connection but it shows unindentified network, in properties gateway IP is absent. i also get 169.254.1.38 as IPv4.What could have happened to the modem, I can't use it at all at the moment?
View 3 Replies View RelatedCan't find WAG160N firmware upgrade download page on this site A few mounth ago it existed
View 3 Replies View RelatedI cannot access the Username and password on my WAG160N - the ones I thought were correct do not accepted, nor are the quoted 'defaults'.I have tried holding down 'reset' for 30 secs; I have tried powercycling the router after and during this; I have tried 'resetting' with the phone and ethernet connections unplugged. This is NOT returning the machine to the default settings - and neither is it 'wiping' the existing settings for my ISP.The amusing thing is - it works perfectly well, but I can't alter my security settings and I can't alter other settings if I change my ISP (as I was intending to do).
View 9 Replies View RelatedI have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedTwo years ago I bought a WAG160N for modem (ADSL) and router functionality. I consider to buy a pure router (E3000 or E4200) to connect to the WAG160N and use that one purely as the modem. How and what should I configure/disable on my WAG160N?
View 3 Replies View RelatedWhy can I not register a WAG160N router with Linksys? Is this because these devices are not sold in the US?
View 4 Replies View RelatedI purchased a new WAG160N router a few months ago and recently I have been having major problems with connectivity.The problem is that it resets itself at seemingly random times. I see it happening. The red power light starts flashing red and then the other lights slowly turn green as it re-establishes connection to the internet.
This is becoming extremley frustrating as I do online gaming with my XBOX 360.I use wired connections using ethernet cables. One to my laptop. And one to my XBOX 360.I have contacted my ISP who have done line checks and I have had an engineer look at my line and all is good. I have also replaced all cables to/from the router including phone cords and ethernet cords. EVERYTHING is new.I recall one incident in which my internet was down and I just couldnt get connection AT ALL. I rang my ISP and they got me to log into my modem settings. The settings were all altered for some reason and I have no idea why. When they told me to enter the details in the settings the internet worked immediatley.
Last night we had some pretty bad lightning and thunder and our Linksys WAG160N appears to have had a bit of a fright.As I was going round unplugging items in case of a hit (this was after a flash or two, relatively nearby), all the lights on the router were off except for the ethernet light (plugged into a Linksys homeplug adaptor). Now the router doesn't appear to boot. When powered on, the power light doesn't flash or anything to indicate booting up, all you get is the ethernet light (if connected) after a few seconds, but no activity. I'm presuming something has been fried or corrupted? I'm not sure if we did have a power spike either through the mains or phone line as all other equipment seems to be fine, but I'm wondering the the homeplug connection might of had something to do with it after reading a few posts from others on the subject.I've held in the reset button while starting and it doesn't appear to have done anything. I will try the 30/30/30 reset tonight.
View 1 Replies View Related I have an issue with my router that disconnects from the internet in variuos situation when my laptop (an hp pavillion dv6) try to connect. It happen everytime when the laptop go in standby. When i turn it on from standby, the router disconnects from the net and the only way to have access to internet again is turn off and then on the router. It happens also when i turn on the laptop if there is yet some other device connected, like my desktop or my iphone or whatever.
Sometimes i have the same problem with my brand new tablet (a sony s) in a slightly different way. I navigate then, after a random amount of time, the router disconnects in the same way and the only way to have back connection is turn off and then on the router.
I recently bought a Linksys WAG160N v2 model to replace my old setup of a Linksys WRT54GL + ASUS AM604g (ADSL2+ Modem) i had.I've set it up to dial my ISP's PPPoE connection as i had on the previous setup exactly, And it seemed to work at first.But now i've randomly noticed the connection just dies - the router doesn't respond to wireless at all anymore, and connecting from a wired machine shows the PPPoE link died, while the log says something along the lines of "PPPoE connection terminated: transport endpoint not connected" followed by a big number with lots of zeros and :'s. Probably some kind of IPv6 error address? note that i am not using IPv6 myself nor does my ISP provide any such addresses.
I've already upgraded the firmware to latest and installed the newest WiFi drivers on the machine i was connecting from wirelessly (has an Intel Wifi Link AGN5300 module).
I bought router WAG160n half year ago. At the begining router worked ok but now I have a problem. Sometimes my Internet slow down. When Internet works bad I have problem with open router websites and when I send ping to router I have very bad answer like 300-2000 ms (distance router to computer 3 meters). Than I restart router and everything is ok. Aha, Internet with cable works ok everytime.I have problem when I send big file to another computer with Wi-Fi
View 4 Replies View RelatedI have d-link wireless router which is connected to the internet, also I have Linksys (WAG160Nv2) which i want to use it as access point by link it to D-link router using ethernet cable in order to use the wireless internet. D-link router settings shown below
I changed the settings of linksys router as shown below
I have to change ISP, as mine is closing down , and the new ISP will be sending a N router - which may have 5Gh - so I'm thinking of replacng a "G" AP with the WAG320N and use the 5Ghz range. The WAG320N will be used with a USB Music harddrive and a TV and PVR connected to it - so my music will be direct to the DLNA devices - and also provide any devices with a 5Ghz signal
View 9 Replies View Relatedi have 2 linksys modems wag120n and wag320n.i am using wag320n as my primary modem and i want to set up wag120n as an access point to provide internet access in another room. what should be the configuration of wag120n?and yes i have read all the post about this subject and tried it all but since there was no actual solution for this problem i decided to open a new post.
View 1 Replies View Relatedi have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
My devices will connect to 192.168.0.0 network
Is it possible to "tweak" the SNR on the WAG160n?
View 4 Replies View RelatedI've just been sent a new ADSL modem router by my new broadband supplier and plan on using it. However, my question is, can use my old wag160n to replace one of these, which im currently using to connect an old xbox to my wireless network, but also make use of the other lan ports on the wag (i.e. Connect more than one non wireless device to the wag and gain access to my wifi network?)
View 1 Replies View RelatedI've a 20Mbit/s connection with Telecom Italia provider.My line values follows:-- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 8/35DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel:DSL Upstream Rate: 979 KbpsDSL Downstream Rate: 22105 Kbps Down upDSL Noise Margin: 12.0 dB 13.4 dBDSL Attenuation: 10.5 dB 4.3 dBDSL Transmit Power: 14.0 dBm 12.4 dBm?I have issues about connection stability : on HEAVY load download the PPP connection goes down. The sync signal stays up, but the PPP goes down!
In the log these lines corresponds:
Sun, 2013-01-20 23:29:29 - No response to 3 echo-requests
Sun, 2013-01-20 23:29:29 - Serial link appears to be disconnected.
Sun, 2013-01-20 23:29:29 - Enter: tdb_store.
Sun, 2013-01-20 23:29:29 - tdb_store: calling tdb_update.
Sun, 2013-01-20 23:29:29 - Enter: tdb_update.
[code]....
My ISP says that there are no troubles with the line and it can be an issue of the modem...
When I enable the debug with ?todo=debug shall I see more info in the logs ?How to stop the debugging ?How to print the logs ?What is the difference with debug and ppp_debug ?What is the effect of the sendlog command ? I didn't receive any email with a log !
View 3 Replies View RelatedWhen i connect my WAG160N V2 to DSL, i don't get link, but if i tried whit a friend´s modem i get link. I use the same cables and dsl split.
View 1 Replies View RelatedI have had trouble setting my WAG120N as router.
I am connected to internet via a cable modem, via the LAN cable, I connect cable modem to WAG120N that I want to use as an wireless access point only. And I have got 2 PC, 1 runs on XP, the other on runs on Windows 7. My XP would have no trouble to connect to wireless, but the Win7 can only connect to wireless network, but no internet. When I try the troubleshooting from Win 7, it says, DNS server isnt responding The setting I am using at the moment is Bridged mode only, without entering any values of DNS, IP, etc Is there any setting that work for both OS?
Is it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies View RelatedI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedStruggling to enable Airplay using a WAG160N. Any settings I need on the router? Looking on forums, came across suggestion to disable WMM support. This seemed to work and i had Airplay but now I've lost it again.
View 1 Replies View RelatedWAG160N
S/N: SSH00H406302
MAC: 001D7EB42921
Manufactured 04/2008
I can no longer access the internet, and the internet has been difficult to bring up for one to two weeks.Internet light does not come on. Under Status tab, interface is down, tried refresh and connect but nothing.The IP address can be pinged, 4 packets sent and 4 packets received. Tried resetting defaults and refreshing but no success.Bought this router in September 2008 to replace WAG54G which was constantly turning on and off every few seconds.
Some years ago i have buyed a WAG160N i haven't never used, because once i plug it power, it start to reboot and reboot in a loop...Is there something to do with it or should i put it in the trash ? Firmware using is probably Ver.1.00.15?
View 6 Replies View RelatedI have a WAG160 setup to use the one fo the LAN ports as a WAN connection. The issue is every now and again the internet connection drops and it seems it is unable to communicate with the DNS server that is providing the internet connection.
View 9 Replies View RelatedAny hardware that can re-boot a DSL router such as the WAG 160N when the router no longer passes traffic ? Today, while the DSL line and the Internet appeared to be working, I could not log in to the router from a LAN machine and I had to power it off and on again by hand.We have a number of surveillance cams on the LAN and this must not happen, that the cams cannot be accessed, in particular if nobody is on site for a few days.Unfortunately, the WAG 160N does not have a daily re-boot option. What can one do except for installing a timer that switches the power to the router off and and on again ?
View 5 Replies View RelatedI'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
View 6 Replies View Relatedi trried te update the firmware of my WAG160N. I had to choose between two versions. I tried both. But both versions give the message that is the wrong version and the installations stops.
View 9 Replies View RelatedI have a wag160n and would like to disable the wireless and use as a wired ASDL modem. I can't see any obvious settings I'm the setup or buttons on the unit but was wondering if I were to set the DHCP to disable if
View 4 Replies View Related