Linksys Cable / DSL :: WAG120N Red Power Light
Apr 4, 2012
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies
ADVERTISEMENT
Dec 26, 2011
I recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies
View Related
Aug 28, 2012
Yesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
View 8 Replies
View Related
Jan 24, 2009
Ive recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.
View 8 Replies
View Related
Oct 29, 2011
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies
View Related
Jun 19, 2012
My Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies
View Related
Jul 4, 2006
My Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies
View Related
May 11, 2009
So I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies
View Related
May 17, 2008
My router was working fine until today. I figured it out when I tried to get on the internet and it wouldn't let me. I hooked up the ethernet directly from my modem to my computer and then my internet worked fine.
View 4 Replies
View Related
Oct 29, 2011
I need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
View 9 Replies
View Related
Feb 3, 2012
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies
View Related
Feb 20, 2012
No download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
View 7 Replies
View Related
Sep 9, 2011
I have WRT 120 N which has apparently stopped working. When I turn it on, only the power led turns on without blinking, no other light flashes. My computer can't detect the router signals since the signal light is off. Neither does my modem show that the router is connected to it through the ethernet cable. My ethernet cable is working fine, since it is working directly with the computer.
View 6 Replies
View Related
Feb 21, 2012
I have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies
View Related
Mar 24, 2011
I've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies
View Related
Oct 2, 2011
i have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies
View Related
Aug 15, 2011
If I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies
View Related
Feb 19, 2011
Unable to stop the power light from blinking on a BEFSR41 tried updating the firmware.I have tried resetting the router using the rest button, for 3 seconds, 10 seconds, and 30 seconds, nothing works.Tried running the setup disk, but it does not see the router. Is there a repair tool that I can download?
View 4 Replies
View Related
Apr 22, 2009
My wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies
View Related
Aug 7, 2011
I have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.
View 5 Replies
View Related
Nov 8, 2012
I have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies
View Related
Apr 25, 2009
So I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
View 9 Replies
View Related
Nov 20, 2011
I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies
View Related
Aug 24, 2012
Is there any way to disable WPS feature on my WAG120?
View 1 Replies
View Related
Mar 31, 2011
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies
View Related
Jul 20, 2011
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies
View Related
Apr 19, 2012
I have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies
View Related
Mar 27, 2011
I've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies
View Related
Jul 22, 2011
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies
View Related
May 14, 2012
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
View 1 Replies
View Related
Jan 31, 2012
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies
View Related
Jan 24, 2011
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies
View Related
Oct 24, 2010
I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
View 6 Replies
View Related