I need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies View RelatedMy Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies View Relatedthe power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies View RelatedI've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies View RelatedSo I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies View RelatedNo download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
I have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies View RelatedIf I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies View RelatedMy wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies View RelatedI have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies View RelatedI'm having a problem with my WRT54G wireless broadband router. The power light is blinking and I can no longer access the internet. What should I do. I can't seem to understand the self-help on your site.
View 2 Replies View RelatedUnable to stop the power light from blinking on a BEFSR41 tried updating the firmware.I have tried resetting the router using the rest button, for 3 seconds, 10 seconds, and 30 seconds, nothing works.Tried running the setup disk, but it does not see the router. Is there a repair tool that I can download?
View 4 Replies View RelatedIve recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.
View 8 Replies View RelatedMy router was working fine until today. I figured it out when I tried to get on the internet and it wouldn't let me. I hooked up the ethernet directly from my modem to my computer and then my internet worked fine.
View 4 Replies View RelatedI have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
View 1 Replies View RelatedI successfully linked a DIR-655 (A4, FW:1.21) via WPS.
I then updated the DAP-1522 to FW:1.21 from 1.1.
Things looked great. I then moved it upstairs to my home theater.
Plugged it in and got a blinking power light. Completely unresponsive to either linkage or 192.168.0.50.
I have followed everyone advice listed either here or in Amazons reviews. And from my own experience with similar electronics the flashing power LED is indicative of a "brick".
I have initiated a replacement shipment from amazon. Just wanted to see if anyone had seen this before.
I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies View RelatedGot the EA2700 router and got the blinking defective firmware light right out of the box
View 3 Replies View RelatedWRT54G V4, how can i fix this router that has the power led blinking non stop? i flashed ddwrt to it and the power went out half way through flashing. i cant ping 192.168.1.1
View 9 Replies View RelatedSo I just noticed on my Cable modem the link light is blinking orange, per Motorola if its blinking orange - Computer is connected via a 10 mbps or 100 mbps Ethernet port.
On the Linksys E4200 status page it says
Internet Port Speed:
Internet 10/100 mbps
Local Port Speed Port 1 - 1Gbps
Maybe I just noticed this with this router, but I'm pretty sure this didn't start happening until I updated to 1.0.03.
Previously the link light was blue indicating a 1Gbps connection.
I'm using an E2500 and the Power LED started blinking this week.From the manual, this means “Flashes slowly during bootup, during firmware upgrades, and druing a Wi-Fi-Protected Setup Connection.” We have a wireless printer (wireless disabled), and a Kindle that does use wireless. All other computers are hard wired. I have not started a Wi-Fi protected setup. The router has been in use since the third week in October, and is more or less OK even though the Power LED is flashing. How do I get the Power LED to stop flashing?
View 3 Replies View RelatedI have a problem with a LinkSys WRT610N router (v1).
I have just bought it used. The problems: I see the power led blinking all the time. I can't connect to 192.168.1.1. I do not notice any effect on the leds when pressing the reset button (I feel a soft click when I do that, but none of the leds seem to realize). The manual states that the led should stop blinking after the "self-diagnostics" ends.
My configuration is DSL connection (by AT&T, phone cable), a Siemens 4100 modem, an ethernet cable into the LinkSys router, then an ethernet cable into a Linux PC. Everything is wired. I see the green light of the LAN connection to my PC, the world blue icon and the USB icon stable on, a shy orange led on in the middle (wireless?) and the power blue led blinking. The PC is configured with DHCP, and I can access both the modem (192.168.0.1) and the internet. The gateway address is the one of the modem (again 192.168.0.1). In summary, the ethernet of the router seems to work, but the router is completely transparent, inaccessible, unconfigurable, apparently unresponsive. Trying to connect to 192.168.1.1 (the supposed default address of the web interface of the router, which is different from the 192.168.0.1 of the modem) I get a timeout error, and I can't ping that address. The modem is configured to handle the PPPoE connection, which I am not sure what it means but the text description suggests in this mode I should be able to access the router, provided that its address is not conflicting with the modem's. If I disconnect the modem from the router, DHCP does not get any address. If I force one, 192.168.1.1 still does not respond to pings.
So Is it normal not to notice any reaction when hitting the reset button? is the object just broken, except that the ethernet subsystem still works?
I am on a surge protector and we lost power last night. This morning we were stilling experiencing a brown out but now the power is back 100%. I've walked through the E1000 router reset and not matter what I do, all the lights except the power light blink rapidly and dimly. Could the router be fried even though it's on a surge protector???? It's less than 6 months old so hopefully still covered by warranty.
View 9 Replies View RelatedI went online with a tech real quick before I found I beyond complimentary tech support. They say my router is working like a switch. I cannot get any wireless access and to the three direct connections to the router only one is working. The lights are constantly blinking, with the power light blinking every so often
View 1 Replies View RelatedI have a problem with RV042. My ISP gives me automaticly IP address and i had no problems using different types of routers, including linksys routers. With RV042 i just can't get the IP. It says, the port is up, i see the packets/traffic, front control light is blinking but it never receives the dhcp settings, doesn't matter if i use wan1, wan2, dual wan mode or single wan. I have the newest firmare 1.3.12.19tm. System statistics says "disconnected" but the packets come in and go out. Log shows absolutely nothing. I also disabled firewall but it didn't work. I can't seem to find the older 1.3.12.6 firmware.
View 7 Replies View RelatedMy Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies View RelatedI have WRT 120 N which has apparently stopped working. When I turn it on, only the power led turns on without blinking, no other light flashes. My computer can't detect the router signals since the signal light is off. Neither does my modem show that the router is connected to it through the ethernet cable. My ethernet cable is working fine, since it is working directly with the computer.
View 6 Replies View Relatedi have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies View Related i tried to upgrade my BEFSR41 model 4.2 to a newer firmware (FW_BEFSR41v4.3_2.00.4.5_20080603_code.bin) and got a blinking power led. I've tried to power cycle (several times), reset (several times, 30/60 secs), unbrick (several times) and still have flashing power led. My connection to the router looks like:
Request timed out.Request timed out.Request timed out.Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Reply from 192.168.1.1: bytes=32 time<1ms TTL=64Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Request timed out.Reply from 192.168.1.2: Destination host unreachable.Request timed out.(and offline until the next reset)
I have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.
View 5 Replies View RelatedSo I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
View 9 Replies View RelatedI have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies View Related