i have here Cisco 877 model, when i turn it on the CD light keep flashing,there is no connection to connect to router to configure it,i tried to connect with Consol, and UTP but no vail,i clicked the RESET button btw the consol and ADSL button unfortunatly no vail,
View 1 RepliesI just purchased a new E4200 to speed up my network and all seems to be fine with the exception of the Cisco light flashing rapidly which indicates a problem.
View 5 Replies View RelatedI have a 1921 router with a V.2 T1 wic installed connected to a MPLS circuit. The circuit is down hard and the CD light is flashing. We reseated the WIC card and the circuit recovered for about 30 seconds, then went down and CD began flashing again on the WIC. AL is solid.
View 1 Replies View RelatedSo, I messed around with my router a little too much and just want to restore it back to the original firmware now. I have a WRT54GS v7 Linksys router and tried to follow this guide to flash the firmware to something a little more useful. After step 7 of that guide, I can't ping my router, can't access the GUI, and have no idea what my router's IP is. If I assign each computer plugged into the router an IP like 192.168.1.2 I can ping them, so the router is still functioning somewhat. I'm plugged into my modem right now to get on the Internet.
Right now, my power light is off, my DMZ light is off, my WLAN light is off, but the other lights turn on if I plug a cord into its port (plug a computer into port 1, port 1's light comes on). When I do an ipconfig /all i get this. I doubt the web interface still works, but if I could at least get the router's IP, couldn't I use tftp and put the firmware on that way?
I changed the setting from static to dynamic and the switch froze up. all lights on the panel flashed, when they stopped the system light on the left side continued to flash. I tryied unplugging unit as well as depressing the reset for longer than 30 seconds. Unit still the same.
View 8 Replies View RelatedI switch to a new internet provider. which is wireless[Frontier]. my printer is dell V715w the orange light is flashing. provide detailed info to correct
View 1 Replies View RelatedI have a new TEW-692GR router attached to an UBEE DVM3203B cable modem. For the last several days the WAN light on the router and the LINK light on the cable modem flash on a continual basis. This seemed to happen after establishing a wireless connection between a new LG smart tv and the router but am not sure if that in fact caused the issue. I have power cycled all devices on my network in an attempt to clear this up but no joy.
View 2 Replies View RelatedI have an HP deskjet f4580 printer which i am trying to connect wirelessly and print from my laptop. virgin recently installed a new hub/router and now i cannot seem to print wirelessly. i have just removed and reinstalled printer but can only print via usb?
View 1 Replies View RelatedI have an HP deskjet f4580 printer which i am trying to connect wirelessly and print from my laptop. virgin recently installed a new hub/router and now i cannot seem to print wirelessly. i have just removed and reinstalled printer but can only print via usb
View 1 Replies View RelatedReset button pushed in, unplugged won't reset it. I get my default name on connections but it's not showing as available connection.
View 7 Replies View RelatedI am having a problem with my ea4500 several times a day the cisco light flashes and I loose internet connectivity. I have tried resetting the router by the reset button and changed ssid name, making two different one for each band, and still I am having a problem. I have read where it could be a firmware update, I have updated (using current version)
View 6 Replies View RelatedWe have a Cisco SRP 527W router that was not showing up on the LAN. so we tried a Factory Default reset but it seems to be dead.
The power light is flashing constantly,the 4 LAN light are constantly on,the DSL Data light comes on for 1 sec when device is powered up.
i have tried connecting directly to a PC, the NIC reports as network cable unplugged.i have tried the (power on device, hold down reset button, power of after 30 sec, power on after 5 sec, release reset button after 5 sec) but still "network cable unplugged".
the firmware flash utility will not find the NIC the device is connected to.the router is less than a year old, is there a fix or is it a warranty replacement ?
I recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies View RelatedMy N600 router has a flashing orange light on it. What's going on with this thing?
View 4 Replies View RelatedWe just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies View RelatedI have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.
View 11 Replies View Relatedi have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies View RelatedSo I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
View 9 Replies View RelatedIs it normal for the "CISCO" icon/light to "fast flashing" periodically - not to be confused with the "slow flashing" that the E4200V2 displays when being "power cycled"?
View 1 Replies View RelatedEverything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
I have a HP Pavillon dv6000 laptop, tried connecting to my wireless network this morning but no luck. It will connect fine when using Ethernet cable. Whether the switch is pushed to on or off the light stays orange, when it is connected it used to turn blue. I've included a prtscrn of my device manager...
View 3 Replies View RelatedFor the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
View 1 Replies View RelatedI recently switched my router from an older Linksys WRT 54GS to an E3000. The WRT 54GS was working perfectly fine, but I needed to upgrade to a 802.11n router to use with some of my devices at home. I unplugged all the cables from the WRT54GS, and connected all the cables into the E3000 - in the exact same sockets and order they were on the old router. When powering on, all the lights eventually turned on (Power, Internet and Ports 1 to 4), except the wifi is still off. I tried running the installation CD, but it says it cannot find the network. I tried a reset (back button) as well as 30-30-30 reset, but no matter what I do, the wifi indicator still doesn't turn on. When switching back to the old router, it has no problem broadcasting a wifi signal again. Is there anything else I should try, either on my PC settings or the E3000 router itself?
View 5 Replies View RelatedI previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View RelatedI am trying to light up every port light on a 3750g. There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?
View 3 Replies View RelatedWe have two WAP4410N access points that are behaving identically. When connected without an ethernet connection, the Power light comes on and stays on. However, as soon as you attach an ethernet cable, whether it's attached to anything on the other end or not, the LEDs on the devices start blinking - first the Power light, then the Wireless light, repeatedly. They continue to do this, even when the ethernet cord is removed.
In addition to this, I cannot ping the IP, even when the WAP directly connected to a PC in the same subnet. I tried a hard reset, but I can't even ping the default IP.
Both WAPS have a very basic configuration. Neither of them are running upgraded firmware.
I was replacing a bad cap on my DIr-615 and noticed I have the 635(or 625?) board except there is no USB port or 3rd antenna soldered on.I soldered on a 3rd antenna from an old linksys router but don't know if it's working.If I flash the DIR-635 FW(I'm using DD-wrt) will it work fine and enable the antenna to work? Will having a third antenna even be beneficial at all for range and signal strength?I plan on flashing DD-wrt firmware for the 635 if that makes any difference.
View 3 Replies View RelatedA customer's ASA is presenting the System LED flashing red.I have already analysed the show tech-support and show environment output: Found nothing, everythink seems OK.Cisco ASA 5580-20 - 8.2.1.Single appliance, no failover, multiple context and transparent mode.
View 5 Replies View RelatedIn my ASA 5580-20 system LED is flashing RED how can i trobleshoot this.
I checked rarepanel everything is ok also i saw environment also showing ok
Had this Dlink Air plus router with an wireless adator set up on with a PC running win Vista, but as the PC had problems I tried it with older XP PC and it worked fine for about 5 weeks but tonight the wireless adaptor on my desk has stopped flashing and I could not access the internet so I decided to try the Vista PC and it works fine on there, while it can get me online I would still like to fix the D Link to work with the older PC again, what is the problem as it is a faster more reliable PC
View 5 Replies View RelatedMy NIC card started flashing last night. The computer was turn off, and the network cable to the cable modem was unplugged. Also, I installed some free software that day and wonder if there is a connection.
View 5 Replies View RelatedHow to flash a DIR-601 Rev B1 with any of the custom firmwares out there? I've tried all of them this morning and haven't had any luck. I set the router to recovery mode and tried openwrt, dd-wrt, tomato, and gargoyle. I tried with chrome, firefox, ultra simple web browser, and ie 8. Every attempt resulted in "Upgrade Failed". I know Rev A1 is supported by DD-WRT, just sucks newegg sent me a B1. Looks like several other routers run similar hardware, so it's got to be doable.
View 5 Replies View RelatedI have a SRP527W what has a constantly flashing power LED.Is there anything that I can do to attempt to recover this router?
View 2 Replies View Related