Trendnet TEW-692GR - Router Continuous Flashing WAN Light
Dec 12, 2011
I have a new TEW-692GR router attached to an UBEE DVM3203B cable modem. For the last several days the WAN light on the router and the LINK light on the cable modem flash on a continual basis. This seemed to happen after establishing a wireless connection between a new LG smart tv and the router but am not sure if that in fact caused the issue. I have power cycled all devices on my network in an attempt to clear this up but no joy.
View 2 Replies
ADVERTISEMENT
Feb 29, 2012
How to configure a TrendNet TEW-692GR to block/limit Facebook and other websites on one or all computers that access the wireless router.We homeschool and the boys are having trouble dealing with the distraction of social media while using their computers to get school work done.
I've tried listing FB IP address ranges (the 66s, 69s and the 204s) in Access Control and under IP Range Block Rules, and using the schedule page to set an access schedule. Everything looks reasonable but we can all still access FB. What am I missing? I think I found all the IPs for FB, maybe not? Not truly clear if the schedule is for times to block or times to access.
View 1 Replies
View Related
Jul 31, 2011
So, I messed around with my router a little too much and just want to restore it back to the original firmware now. I have a WRT54GS v7 Linksys router and tried to follow this guide to flash the firmware to something a little more useful. After step 7 of that guide, I can't ping my router, can't access the GUI, and have no idea what my router's IP is. If I assign each computer plugged into the router an IP like 192.168.1.2 I can ping them, so the router is still functioning somewhat. I'm plugged into my modem right now to get on the Internet.
Right now, my power light is off, my DMZ light is off, my WLAN light is off, but the other lights turn on if I plug a cord into its port (plug a computer into port 1, port 1's light comes on). When I do an ipconfig /all i get this. I doubt the web interface still works, but if I could at least get the router's IP, couldn't I use tftp and put the firmware on that way?
View 3 Replies
View Related
Apr 26, 2012
I have a 1921 router with a V.2 T1 wic installed connected to a MPLS circuit. The circuit is down hard and the CD light is flashing. We reseated the WIC card and the circuit recovered for about 30 seconds, then went down and CD began flashing again on the WIC. AL is solid.
View 1 Replies
View Related
Jun 22, 2012
Reset button pushed in, unplugged won't reset it. I get my default name on connections but it's not showing as available connection.
View 7 Replies
View Related
Jan 6, 2013
I am having a problem with my ea4500 several times a day the cisco light flashes and I loose internet connectivity. I have tried resetting the router by the reset button and changed ssid name, making two different one for each band, and still I am having a problem. I have read where it could be a firmware update, I have updated (using current version)
View 6 Replies
View Related
Dec 26, 2011
I recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies
View Related
Nov 25, 2012
We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies
View Related
Oct 2, 2011
i have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies
View Related
Apr 25, 2009
So I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
View 9 Replies
View Related
Jun 6, 2012
Is it normal for the "CISCO" icon/light to "fast flashing" periodically - not to be confused with the "slow flashing" that the E4200V2 displays when being "power cycled"?
View 1 Replies
View Related
Jun 2, 2011
i have here Cisco 877 model, when i turn it on the CD light keep flashing,there is no connection to connect to router to configure it,i tried to connect with Consol, and UTP but no vail,i clicked the RESET button btw the consol and ADSL button unfortunatly no vail,
View 1 Replies
View Related
Jul 18, 2011
I just purchased a new E4200 to speed up my network and all seems to be fine with the exception of the Cisco light flashing rapidly which indicates a problem.
View 5 Replies
View Related
Apr 28, 2012
Everything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
View 3 Replies
View Related
Feb 22, 2011
I switch to a new internet provider. which is wireless[Frontier]. my printer is dell V715w the orange light is flashing. provide detailed info to correct
View 1 Replies
View Related
Jun 27, 2012
I have an HP deskjet f4580 printer which i am trying to connect wirelessly and print from my laptop. virgin recently installed a new hub/router and now i cannot seem to print wirelessly. i have just removed and reinstalled printer but can only print via usb?
View 1 Replies
View Related
Jun 27, 2012
I have an HP deskjet f4580 printer which i am trying to connect wirelessly and print from my laptop. virgin recently installed a new hub/router and now i cannot seem to print wirelessly. i have just removed and reinstalled printer but can only print via usb
View 1 Replies
View Related
Mar 14, 2013
I changed the setting from static to dynamic and the switch froze up. all lights on the panel flashed, when they stopped the system light on the left side continued to flash. I tryied unplugging unit as well as depressing the reset for longer than 30 seconds. Unit still the same.
View 8 Replies
View Related
Oct 11, 2012
My N600 router has a flashing orange light on it. What's going on with this thing?
View 4 Replies
View Related
Aug 9, 2011
We have a Cisco SRP 527W router that was not showing up on the LAN. so we tried a Factory Default reset but it seems to be dead.
The power light is flashing constantly,the 4 LAN light are constantly on,the DSL Data light comes on for 1 sec when device is powered up.
i have tried connecting directly to a PC, the NIC reports as network cable unplugged.i have tried the (power on device, hold down reset button, power of after 30 sec, power on after 5 sec, release reset button after 5 sec) but still "network cable unplugged".
the firmware flash utility will not find the NIC the device is connected to.the router is less than a year old, is there a fix or is it a warranty replacement ?
View 2 Replies
View Related
May 7, 2012
I have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.
View 11 Replies
View Related
Jul 22, 2011
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies
View Related
May 21, 2012
We just had a TEW-72GR router fail and replaced it with a TEW-GR. Now I am unable to get to my domain (mydomain.net) from outside the network. Inside the network, all appears to be fine. I can enter that address and get to the site with no issues.We use SBS 2008 with windows 7 clients.All clients can get out to the web, we can send and receive emails, but I can not access the domain.
View 2 Replies
View Related
Dec 9, 2012
security key for trendnet router
View 1 Replies
View Related
Apr 23, 2011
I have just set up a wireless trendnet router. Everything is set up normal and its working correctly, it correctly assigns internal IPs to wireless devices. The problem is though that for some reason we all get disconnected in games for instance and some games more than others. Rift disconnects every 30 seconds to 1 minute, World of Warcraft disconnects often, Live Messenger disconnects as well, Age of Empires Online can sometimes work fine for hours, then sometimes disconnect every now and then. Steam doesn't disconnect. Its more or less the same on any of our laptops. (all running Windows 7 64 Bit Home Premium or Professional)
View 2 Replies
View Related
Feb 4, 2011
I have just made a new home network with a Trendnet TEW-652BRP N router.I am trying to set up my encryption but I am confused on it. Under Security "Authencation Type" there is WEP, WPA, WPA-2, WPA-AUTO. What are these settings for and which do I choose for a home wireless net work?
View 3 Replies
View Related
Nov 14, 2011
Have lost the instructions on how to connect my TRENDnet wireless router to my att DSL modem, not sure if I have all the cords that I need.
View 1 Replies
View Related
Aug 21, 2012
My internet connection setup is: PC -> Trendnet 632 BRP wi-fi router (via Ethernet cable) - > D-Link DSL-2520U modem (via Ethernet cable, PPPoE) -> Internet. I have other devices connected to my Trendnet router via Wi-Fi connection (Notebook, PS3, XBOX, iPhone).My ISP gave me two DNS servers wich I have entered in my Trendnet. But when I look at the DNS tab in my D-Link I see two different DNS servers witch is not the same I entered in Trendnet.hey was set automatically when I created new DSL connection. I've also tried to leave the DNS adress tab as it was by default (0.0.0.0) in Trendnet router and after that my network still works normal. And when I look at the WAN status tab in Trendnet settings the DNS servers is set automatically to 192.168.1.1.So I have 3 questions for you:1) Do I really need to enter those DNS servers that my ISP gave me or I can just leave it to DHCP to manage them?2) If I have entered ISP's DNS servers in Trendnet then witch DNS servers is actually I'm using the ones my ISP gave me or the ones that my D-Link have picked automatically?
View 11 Replies
View Related
Jun 11, 2011
I have set up a wireless home network using ADSL with the following components: TrendNet TEW- 432 BRP Wireless Router Gateway Desktop with Windows 7 OS, iMac desktop with Leopard 10.5.7 OS Compaq Presario Notebook with Vista Home Premium OS Service Pack 2 I am able to connect to the network with all 3 but I have a problem with the Notebook. It is very slow to connect and sometimes takes 15 minutes or more to find the network. Once it is connected it works fine and doesnt disconnect, but if I have to reboot for any reason the same problem occurs. It does not appear to be a problem with the placement of the router and the signal strength which is "very good" to "excellent". I say "slow to connect (again)" because this had occurred before and I returned the laptop under warranty. HP replaced the wireless network card and it worked fine, but the problem has come back over a year later. I suspect that the card is not at fault and that the problem is elsewhere but I am at a loss as to what it might be.
View 14 Replies
View Related
Jul 1, 2012
my acer laptop can detect my neighbour's wifi but cant detect my wifi which i connected today , my router is trendnet , it works perfectly in PC and my Phone can also connect to its wifi , but my laptop wont even detect the wireless network
View 5 Replies
View Related
Dec 21, 2012
Every night I turn everything off via power strip, including the router. Before I turn off the router, my roku connection is good.In the morning, the roku will work for about 20 minutes, then disconnects, and then I'm unable to find the router.I'll then need to reset my router's settings (I have the WRT54GS), and then uplug, and replug the router.It's important that I unplug the router every night.Is there a way to configure the settings so I don't have to reconfigure the settings every morning?
View 4 Replies
View Related
Dec 30, 2012
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
View 8 Replies
View Related
Aug 29, 2011
Trying to connect my Dell Dimension E310 to my Linksys WRT54GS with a TRENDnet wireless N USB adapter. It sees the router, it connects, I show strong signal strength, but get a "limited connection or no connection" error back from the router...can't get on the Internet. If I use an Ethernet wire and connect it to the router, it can set up a wireless connection with the machine, I can unhook the hardwire, and I'm good to go. But every time I reboot, it won't connect unless I set it up with the hardwire first. Impractical.All other devices attached to the router are fine and connected to the Internet. How can I get the router to maintain the settings for this new connection so it will connect wirelessly when I reboot?
View 1 Replies
View Related
