TrendNet TEW- 432 BRP Wireless Router - Network Slow To Connect (again)
Jun 11, 2011
I have set up a wireless home network using ADSL with the following components: TrendNet TEW- 432 BRP Wireless Router Gateway Desktop with Windows 7 OS, iMac desktop with Leopard 10.5.7 OS Compaq Presario Notebook with Vista Home Premium OS Service Pack 2 I am able to connect to the network with all 3 but I have a problem with the Notebook. It is very slow to connect and sometimes takes 15 minutes or more to find the network. Once it is connected it works fine and doesnt disconnect, but if I have to reboot for any reason the same problem occurs. It does not appear to be a problem with the placement of the router and the signal strength which is "very good" to "excellent". I say "slow to connect (again)" because this had occurred before and I returned the laptop under warranty. HP replaced the wireless network card and it worked fine, but the problem has come back over a year later. I suspect that the card is not at fault and that the problem is elsewhere but I am at a loss as to what it might be.
View 14 Replies
ADVERTISEMENT
Nov 14, 2011
Have lost the instructions on how to connect my TRENDnet wireless router to my att DSL modem, not sure if I have all the cords that I need.
View 1 Replies
View Related
Feb 21, 2012
I've installed a Trendnet TEW-694UB wireless adaptor on my laptop and am trying to connect to my home network. I get a message "Acquiring network address" but it never connects.
View 5 Replies
View Related
Apr 23, 2011
I have just set up a wireless trendnet router. Everything is set up normal and its working correctly, it correctly assigns internal IPs to wireless devices. The problem is though that for some reason we all get disconnected in games for instance and some games more than others. Rift disconnects every 30 seconds to 1 minute, World of Warcraft disconnects often, Live Messenger disconnects as well, Age of Empires Online can sometimes work fine for hours, then sometimes disconnect every now and then. Steam doesn't disconnect. Its more or less the same on any of our laptops. (all running Windows 7 64 Bit Home Premium or Professional)
View 2 Replies
View Related
Aug 29, 2011
Trying to connect my Dell Dimension E310 to my Linksys WRT54GS with a TRENDnet wireless N USB adapter. It sees the router, it connects, I show strong signal strength, but get a "limited connection or no connection" error back from the router...can't get on the Internet. If I use an Ethernet wire and connect it to the router, it can set up a wireless connection with the machine, I can unhook the hardwire, and I'm good to go. But every time I reboot, it won't connect unless I set it up with the hardwire first. Impractical.All other devices attached to the router are fine and connected to the Internet. How can I get the router to maintain the settings for this new connection so it will connect wirelessly when I reboot?
View 1 Replies
View Related
Mar 20, 2012
I cannot install the drivers for my TrendNet TEW-423PI network interface card. I am running Windows 7 64-bit with an Intel i7 2700k and an Asus motherboard. I have tried installing with the card already in the computer - no luck. Card out of the computer install and then shut off and put in - no luck. The instructions that come with the card say that after you install the program that instantly runs from the CD provided you should shut off the computer and install the card and when you turn the computer back on the drivers will install automatically. It has failed to do so and although I pulled all possible drivers from TrendNet's site it still stubbornly refuses to even recognize that there are drivers for it to install.
View 2 Replies
View Related
Apr 25, 2011
Network is slow. Can't connect to our windows 2003 server.
View 3 Replies
View Related
Dec 9, 2012
security key for trendnet router
View 1 Replies
View Related
Feb 4, 2011
I have just made a new home network with a Trendnet TEW-652BRP N router.I am trying to set up my encryption but I am confused on it. Under Security "Authencation Type" there is WEP, WPA, WPA-2, WPA-AUTO. What are these settings for and which do I choose for a home wireless net work?
View 3 Replies
View Related
Aug 21, 2012
My internet connection setup is: PC -> Trendnet 632 BRP wi-fi router (via Ethernet cable) - > D-Link DSL-2520U modem (via Ethernet cable, PPPoE) -> Internet. I have other devices connected to my Trendnet router via Wi-Fi connection (Notebook, PS3, XBOX, iPhone).My ISP gave me two DNS servers wich I have entered in my Trendnet. But when I look at the DNS tab in my D-Link I see two different DNS servers witch is not the same I entered in Trendnet.hey was set automatically when I created new DSL connection. I've also tried to leave the DNS adress tab as it was by default (0.0.0.0) in Trendnet router and after that my network still works normal. And when I look at the WAN status tab in Trendnet settings the DNS servers is set automatically to 192.168.1.1.So I have 3 questions for you:1) Do I really need to enter those DNS servers that my ISP gave me or I can just leave it to DHCP to manage them?2) If I have entered ISP's DNS servers in Trendnet then witch DNS servers is actually I'm using the ones my ISP gave me or the ones that my D-Link have picked automatically?
View 11 Replies
View Related
Dec 12, 2011
I have a new TEW-692GR router attached to an UBEE DVM3203B cable modem. For the last several days the WAN light on the router and the LINK light on the cable modem flash on a continual basis. This seemed to happen after establishing a wireless connection between a new LG smart tv and the router but am not sure if that in fact caused the issue. I have power cycled all devices on my network in an attempt to clear this up but no joy.
View 2 Replies
View Related
Jul 1, 2012
my acer laptop can detect my neighbour's wifi but cant detect my wifi which i connected today , my router is trendnet , it works perfectly in PC and my Phone can also connect to its wifi , but my laptop wont even detect the wireless network
View 5 Replies
View Related
Dec 30, 2012
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
View 8 Replies
View Related
May 7, 2011
Im using an old tower with XP SP3. Most if not all drivers are up to date.I recently have come home from college where the computer connected to the internet through a cable and i now have to use wireless.I went out and bought a Trendnet TEW-648UB Wireless n adapter, installed it and tried to connect to my home network.It has been going from acquiring network address to no connection every ten seconds then repeating. I am fairly sure that this is not the router because i am on my sisters desktop which is a wireless connection and im on the internet. so far i have:
checked to make sure that WZC is enabled, it is.
tried checking and unchecking the Use Windows to to configure my wireless network settings
enabling and disabling my adapter
reinstalling my adapter
repairing connection
disabling any and all firewalls
ipconfig /release
ipoconfig /renew
netsh int ip reset reset.log
netsh winsock reset catalog
lots of computer restarting
and for good measure i pinged 192.168.4.1 and ping 24.229.54.212 not sure why but kinda frustrated so why not
here's the cmd stuff:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsFrost3>ipconfig[code]....
View 12 Replies
View Related
Aug 17, 2011
While I have been VERY happy using my DIR-655 for the most part, all wireless routers have limitations for expansion across your home.I got my TrendNet TEW-640MB installed last night, and it talks to the 655 perfectly, and now I have 4 ethernet ports at distance across my house. I have also used a couple TrendNet TEW647Ga single port wireless bridge for other parts of my home, but with only a single Ethernet port, you still need a little switch/hub to get the extra ports.
Because these units speak .11N at 300 Mbps, it takes full advantage of the technology the 655 gave me when I bought it back in 2009 (??).
View 5 Replies
View Related
Apr 10, 2012
I recently bought a router with 300+450mbps dual-band connectivity. I have a computer and am looking into buying a wireless n adapter. Should I buy a 450mbps-capable card? They cost much more than 300mbps cards and I'm not sure if the price difference is justifiable if current devices won't saturate all of the bandwith. Also, will a 300mbps card slow a 450mbps network down to "only" 300mbps?
View 2 Replies
View Related
Aug 4, 2011
I installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
View 6 Replies
View Related
Feb 10, 2011
just bought a WD my book world edition 2 NAS and have been trying to tranfer files wirelessly to it but a 700mb file is taking 25mins to trans. my book is connected by ethernet to netgear dgnd3300 router and my laptop has sitecom 300n usb doongle.is there some sort of setting i've missed or is this speed normal?
View 5 Replies
View Related
Jul 11, 2011
I'm having very slow file transfer speeds between the 2 computers on my network. One is a gigabit pc wired (cat6) to the e3000. The other is a wireless N laptop. Both computers running Win7. Speeds are like 1.5 - 2 MB/s. when I connect the laptop to the router with a cable (cat6) I get proper high speed. Trying to figure out if it's a problem with the router or windows or what. Speedtest.net says I'm getting 16 MB/s DL wirelessly to my laptop. Shouldn't wireless N be capable of higher speeds than 1.5 MB/s?? Tests are done approx 10 feet from the router.
View 1 Replies
View Related
Mar 24, 2012
I have recently purchased a Cisco E4200 to replace my D-LINK DIR-655, which I thought was defective because I was getting slow wirless file transfer speed, regardless of setting, location and client.Using the E4200, when I transfer a file from a PC to another, both connected at 300mb on the 2.4ghz band, the file transfer rate reported by windows 7 and networx is from 2MB/s to 3.5MB/s. I think those transfer rates are not acceptable. Is that a good assumption ? I would expect something in the range of 10MB/s (which is what I get with a cheap dlink router, wired)
I also had great difficulty finding a channel. I had to try them all one-by-one as the auto channel selection made my PCs connect at 130mb.The E4200 is setup as follows:
-WPA-Personal
-Channel 5
-802.11n only
I have tried 3 different computers with different network adapters and they all underperform (IMO..).There are no other wireless networks in my area.I also took the E4200 to my office which is very crowed. Every single channel is occupied by several wireless networks. I get a file transfer speed PC to PC of about 2MB.I basically could have kept my DIR-655 as the speeds are identical.
View 4 Replies
View Related
Aug 6, 2011
I am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
My ISP is comcast and I have a Arris TM502G modem
View 4 Replies
View Related
Jul 18, 2011
I have a Gigabyte motherboard that ive just installed into my dads new PC and the gigabit LAN has started taking 60 seconds to connect to router, very annoying...sitting with browser open waiting for it too connect... the issue seem to first appear during windows updates, i uninstalled device driver, rebooted and reinstalled the driver off disk... this sorted the issue.. THEN windows installed more updates, however these were nothing to do with networking (Office updates) and its back ...ive tried downloading the driver from gigabyte (newer) but still the problem persists...
Core-i5 2500k
4Gb 1600Mhz RAM
GTX 460 OC
60Gb SSD Vertex 2E
500Gb Seagate SATA-II
Gigabyte P67A-D3-B3
Windows 7 x64
View 2 Replies
View Related
Apr 10, 2013
i have a trendnet tpe-s44 switch and i need to reset it. it is installed in a network with a pos system, and i need to change the security from wep to wpa-2. i also cannot use the web interface to get to the login screen. from what i gather, it should be admin admin at 192.168.0.1, but the network it came from had a 192.168.5 scheme. i also cannot find a reset button, i even took it apart to look for jumpers. that sucks, i can configure a cisco from the command line almost in my sleep
View 14 Replies
View Related
Feb 16, 2012
I bought Trendnet TEW643 PI wireless adaptor. I installed the software and inserted the adaptor to the slot as per the instructions. When I try configuring through wireless N client utility/ site survey, I cannot see any SSID.. I did try un--installing and re-installing and also driver update. but still of no use. I am not too much expert, but now I need to access the desktop in my office room. Item bought-Trendnet TEW-643 PI Windows Vista-64. Fibre broad band.
View 10 Replies
View Related
Feb 16, 2012
how i can install the device with a mac? bcause wizard setup work only with window
View 1 Replies
View Related
Sep 12, 2012
Need to configure a TEG-S2620is switch (Trendnet) with VLANs I need to set TWO VLANs and make them communicate with eachother via the 802.1Q protocol. These are the details:
VLAN ID 102
Port 20 (802.1Q)
Port 21
VLAN ID 144
Port 20 (802.1Q)
Port 22
Port 23
Port 24
how to configure this setup on our switch?
View 1 Replies
View Related
Feb 25, 2011
I have a trendnet TEW-P1UG when I connect to it by wireless and I am able to click the test printer on the ip page, but I cant just print things?am I meant to link to the print server from my router? or from my pc that I wish to print from?
View 16 Replies
View Related
Feb 29, 2012
How to configure a TrendNet TEW-692GR to block/limit Facebook and other websites on one or all computers that access the wireless router.We homeschool and the boys are having trouble dealing with the distraction of social media while using their computers to get school work done.
I've tried listing FB IP address ranges (the 66s, 69s and the 204s) in Access Control and under IP Range Block Rules, and using the schedule page to set an access schedule. Everything looks reasonable but we can all still access FB. What am I missing? I think I found all the IPs for FB, maybe not? Not truly clear if the schedule is for times to block or times to access.
View 1 Replies
View Related
Feb 21, 2011
A while ago internet access was slowed right down for an hour or so. I have a phone line that comes into the house and then into gateway (10.0.0.2) then ethernet from that to linksys wifi router (192.168.1.1). So I did the following ping and repeated what you see below a few times to see that these results were broadly consistent, which was the case. One other person is connected to linksys via ethernet cord and they might have been on at the time. Questions are.... are these results consistent with contention caused by other user on the linksys? and why can I ping gateway but not the router? That makes no sense to me! I am not annoyed with the other person if he is hogging the network...I like him. I just wonder whats going on. When the internet works results from pinging are all as one would expect
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsNASA>ping 192.168.1.1
[Code].....
View 4 Replies
View Related
May 15, 2013
We are facing network heavy and slow performance at one of our remote site, we are using Cisco2800 series router with same IOS on either of the sites.Our WAN network is running on BGP with EIGRP configured and tunnels were configured on either of the sites. As part of the testing I have removed the tunnel to see the performance was ok from Head office to remote branch and the WAN network is getting heavy and slow down when we put the tunnel back in hub and spoke.
quick info
Cisco 2800 Series router
IOS: (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE
View 1 Replies
View Related
Jul 12, 2011
i set-up the D-LINK DNS 323 NAS unit with RAID 1 (dual 2-terabyte 5400 rpm drives)
it works, but it is slow in copying files between my computer and it (8 minutes to copy 7.94 gig file between NAS and my PC via wire).
i am using netgear WNDR3700 gigabit router. replaced the network wires to the latest spec, and my computer has realtek PCIe GBE network adapter.
this is looking more and more like the NAS RAID 1 is the bottleneck.. possibly 7200 RPM drives would have kicked more ass?
View 2 Replies
View Related
Apr 17, 2013
Today I set up a home network:Cable router plugged in to......Homeplug network, (D-Link DHP-307AV/B 200 MBPS PowerLine Homeplugs) plugged in to a LAN port of......a spare adsl router configured as per here: Connecting Additional Routers | Tech Support Forum...with two desktop machines plugged into the LAN ports of the ADSL router.Both of the desktops have got similar specs, are equi-distant from the ADSL router, and are both connected using Ethernet, not wireless.One of them gets a 9MB/sec ADSL [URL]download, the other can't even bring the webpage up and times out if you ask Google to do a search.Taking out the adsl router and plugging the desktop straight into the homeplug gets a network speed of ~13MB/sec on [URL].Plugging a computer directly into the cable modem gives network speeds of ~40MB/sec on [URL] How can I improve on this, and have it so that both machines can access the Interwebnet at a decent bandwidth?
View 8 Replies
View Related
Oct 12, 2011
Hardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
View 2 Replies
View Related
