Resetting A Trendnet Tpe-s44 Switch?
Apr 10, 2013
i have a trendnet tpe-s44 switch and i need to reset it. it is installed in a network with a pos system, and i need to change the security from wep to wpa-2. i also cannot use the web interface to get to the login screen. from what i gather, it should be admin admin at 192.168.0.1, but the network it came from had a 192.168.5 scheme. i also cannot find a reset button, i even took it apart to look for jumpers. that sucks, i can configure a cisco from the command line almost in my sleep
View 14 Replies
ADVERTISEMENT
Sep 12, 2012
Need to configure a TEG-S2620is switch (Trendnet) with VLANs I need to set TWO VLANs and make them communicate with eachother via the 802.1Q protocol. These are the details:
VLAN ID 102
Port 20 (802.1Q)
Port 21
VLAN ID 144
Port 20 (802.1Q)
Port 22
Port 23
Port 24
how to configure this setup on our switch?
View 1 Replies
View Related
Apr 29, 2013
We have recently received some used computing gear for HPC. With that came a Cisco SFS 7024 infiniband switch, which should handle the compute traffic of the cluster. As the system has been used before, i would like to reset the switch, to configure it anew for our setup. Normally with switches there is a possibility to factory reset it, but I have looked everywhere on the switch and in the online manual with out any luck.I have gone through the part where an OOB IP is given to the switch. I do however not know if the former users has changed this, and what it might be.
View 4 Replies
View Related
Oct 7, 2012
We have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?
View 2 Replies
View Related
Dec 9, 2012
security key for trendnet router
View 1 Replies
View Related
Apr 23, 2011
I have just set up a wireless trendnet router. Everything is set up normal and its working correctly, it correctly assigns internal IPs to wireless devices. The problem is though that for some reason we all get disconnected in games for instance and some games more than others. Rift disconnects every 30 seconds to 1 minute, World of Warcraft disconnects often, Live Messenger disconnects as well, Age of Empires Online can sometimes work fine for hours, then sometimes disconnect every now and then. Steam doesn't disconnect. Its more or less the same on any of our laptops. (all running Windows 7 64 Bit Home Premium or Professional)
View 2 Replies
View Related
Feb 16, 2012
I bought Trendnet TEW643 PI wireless adaptor. I installed the software and inserted the adaptor to the slot as per the instructions. When I try configuring through wireless N client utility/ site survey, I cannot see any SSID.. I did try un--installing and re-installing and also driver update. but still of no use. I am not too much expert, but now I need to access the desktop in my office room. Item bought-Trendnet TEW-643 PI Windows Vista-64. Fibre broad band.
View 10 Replies
View Related
Feb 16, 2012
how i can install the device with a mac? bcause wizard setup work only with window
View 1 Replies
View Related
Feb 25, 2011
I have a trendnet TEW-P1UG when I connect to it by wireless and I am able to click the test printer on the ip page, but I cant just print things?am I meant to link to the print server from my router? or from my pc that I wish to print from?
View 16 Replies
View Related
Feb 4, 2011
I have just made a new home network with a Trendnet TEW-652BRP N router.I am trying to set up my encryption but I am confused on it. Under Security "Authencation Type" there is WEP, WPA, WPA-2, WPA-AUTO. What are these settings for and which do I choose for a home wireless net work?
View 3 Replies
View Related
Nov 14, 2011
Have lost the instructions on how to connect my TRENDnet wireless router to my att DSL modem, not sure if I have all the cords that I need.
View 1 Replies
View Related
Aug 21, 2012
My internet connection setup is: PC -> Trendnet 632 BRP wi-fi router (via Ethernet cable) - > D-Link DSL-2520U modem (via Ethernet cable, PPPoE) -> Internet. I have other devices connected to my Trendnet router via Wi-Fi connection (Notebook, PS3, XBOX, iPhone).My ISP gave me two DNS servers wich I have entered in my Trendnet. But when I look at the DNS tab in my D-Link I see two different DNS servers witch is not the same I entered in Trendnet.hey was set automatically when I created new DSL connection. I've also tried to leave the DNS adress tab as it was by default (0.0.0.0) in Trendnet router and after that my network still works normal. And when I look at the WAN status tab in Trendnet settings the DNS servers is set automatically to 192.168.1.1.So I have 3 questions for you:1) Do I really need to enter those DNS servers that my ISP gave me or I can just leave it to DHCP to manage them?2) If I have entered ISP's DNS servers in Trendnet then witch DNS servers is actually I'm using the ones my ISP gave me or the ones that my D-Link have picked automatically?
View 11 Replies
View Related
Feb 29, 2012
How to configure a TrendNet TEW-692GR to block/limit Facebook and other websites on one or all computers that access the wireless router.We homeschool and the boys are having trouble dealing with the distraction of social media while using their computers to get school work done.
I've tried listing FB IP address ranges (the 66s, 69s and the 204s) in Access Control and under IP Range Block Rules, and using the schedule page to set an access schedule. Everything looks reasonable but we can all still access FB. What am I missing? I think I found all the IPs for FB, maybe not? Not truly clear if the schedule is for times to block or times to access.
View 1 Replies
View Related
Dec 12, 2011
I have a new TEW-692GR router attached to an UBEE DVM3203B cable modem. For the last several days the WAN light on the router and the LINK light on the cable modem flash on a continual basis. This seemed to happen after establishing a wireless connection between a new LG smart tv and the router but am not sure if that in fact caused the issue. I have power cycled all devices on my network in an attempt to clear this up but no joy.
View 2 Replies
View Related
Jun 11, 2011
I have set up a wireless home network using ADSL with the following components: TrendNet TEW- 432 BRP Wireless Router Gateway Desktop with Windows 7 OS, iMac desktop with Leopard 10.5.7 OS Compaq Presario Notebook with Vista Home Premium OS Service Pack 2 I am able to connect to the network with all 3 but I have a problem with the Notebook. It is very slow to connect and sometimes takes 15 minutes or more to find the network. Once it is connected it works fine and doesnt disconnect, but if I have to reboot for any reason the same problem occurs. It does not appear to be a problem with the placement of the router and the signal strength which is "very good" to "excellent". I say "slow to connect (again)" because this had occurred before and I returned the laptop under warranty. HP replaced the wireless network card and it worked fine, but the problem has come back over a year later. I suspect that the card is not at fault and that the problem is elsewhere but I am at a loss as to what it might be.
View 14 Replies
View Related
May 7, 2011
Im using an old tower with XP SP3. Most if not all drivers are up to date.I recently have come home from college where the computer connected to the internet through a cable and i now have to use wireless.I went out and bought a Trendnet TEW-648UB Wireless n adapter, installed it and tried to connect to my home network.It has been going from acquiring network address to no connection every ten seconds then repeating. I am fairly sure that this is not the router because i am on my sisters desktop which is a wireless connection and im on the internet. so far i have:
checked to make sure that WZC is enabled, it is.
tried checking and unchecking the Use Windows to to configure my wireless network settings
enabling and disabling my adapter
reinstalling my adapter
repairing connection
disabling any and all firewalls
ipconfig /release
ipoconfig /renew
netsh int ip reset reset.log
netsh winsock reset catalog
lots of computer restarting
and for good measure i pinged 192.168.4.1 and ping 24.229.54.212 not sure why but kinda frustrated so why not
here's the cmd stuff:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsFrost3>ipconfig[code]....
View 12 Replies
View Related
Aug 17, 2011
While I have been VERY happy using my DIR-655 for the most part, all wireless routers have limitations for expansion across your home.I got my TrendNet TEW-640MB installed last night, and it talks to the 655 perfectly, and now I have 4 ethernet ports at distance across my house. I have also used a couple TrendNet TEW647Ga single port wireless bridge for other parts of my home, but with only a single Ethernet port, you still need a little switch/hub to get the extra ports.
Because these units speak .11N at 300 Mbps, it takes full advantage of the technology the 655 gave me when I bought it back in 2009 (??).
View 5 Replies
View Related
Feb 21, 2012
I've installed a Trendnet TEW-694UB wireless adaptor on my laptop and am trying to connect to my home network. I get a message "Acquiring network address" but it never connects.
View 5 Replies
View Related
Mar 20, 2012
I cannot install the drivers for my TrendNet TEW-423PI network interface card. I am running Windows 7 64-bit with an Intel i7 2700k and an Asus motherboard. I have tried installing with the card already in the computer - no luck. Card out of the computer install and then shut off and put in - no luck. The instructions that come with the card say that after you install the program that instantly runs from the CD provided you should shut off the computer and install the card and when you turn the computer back on the drivers will install automatically. It has failed to do so and although I pulled all possible drivers from TrendNet's site it still stubbornly refuses to even recognize that there are drivers for it to install.
View 2 Replies
View Related
Jul 1, 2012
my acer laptop can detect my neighbour's wifi but cant detect my wifi which i connected today , my router is trendnet , it works perfectly in PC and my Phone can also connect to its wifi , but my laptop wont even detect the wireless network
View 5 Replies
View Related
Dec 30, 2012
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
View 8 Replies
View Related
Aug 29, 2011
Trying to connect my Dell Dimension E310 to my Linksys WRT54GS with a TRENDnet wireless N USB adapter. It sees the router, it connects, I show strong signal strength, but get a "limited connection or no connection" error back from the router...can't get on the Internet. If I use an Ethernet wire and connect it to the router, it can set up a wireless connection with the machine, I can unhook the hardwire, and I'm good to go. But every time I reboot, it won't connect unless I set it up with the hardwire first. Impractical.All other devices attached to the router are fine and connected to the Internet. How can I get the router to maintain the settings for this new connection so it will connect wirelessly when I reboot?
View 1 Replies
View Related
May 25, 2011
I have to keep restting my wep key password for my wireless lap top to access the router. It stays logged on for some time but then is looged off the internet. I have to reset the wep key using my desk top PC and each times the default setting is NOT the password I use. after resetting the lap top recognises the web and I can gain access again. Howver this cycle keeps repeating itself!!! Do I have a hacker who keeps resetting my wep key for their own use?
View 2 Replies
View Related
Jul 18, 2011
We have an ASA5510 which keeps resetting itself for no apparent reason. It does this several times a day and I cannot see any pattern to the times etc. I don't believe it is load related as it also happens overnight when very little is going through the device. When it happens the device just drops off the network (all interfaces) and then when it comes back a few minutes later we can see from the system uptime that it has in fact rebooted itself.I initially thought it was faulty hardware, so I swapped the device for another 5510, but that does the same thing. I then added a third 5510 and configured it in with the second one as an Active/Passive failover pair. Both devices do the same as the first, the only differences now is that the passive device kicks in and takes over, so we have a little less service disruption each time.
View 9 Replies
View Related
Dec 13, 2012
Alright so, for the past few weeks, the modem has been resetting itself, by that I mean, I am browsing the net/playing something, then the four lights turn into 1 blinking.. then 2 blinking.. then 3 blinking.. then return to 4 lights and I get my connection back, this is happening every 5-10 minutes and terminates game sessions.
View 1 Replies
View Related
May 11, 2012
is there a way to disable reseting SMC router
View 1 Replies
View Related
May 6, 2011
Recently, whenever I download something my internet will just crash for a second, I think it may be realted to my router because the internet light on my router changes from the connected state (solid blue) to the connecting state (flashing orange) at the same time. The router I use is a belkin router and I have access to its gateway using my internet browser. recently reformatted my c drive to fix a bsod on this pc, before this reformat this problem did not exist.
View 5 Replies
View Related
Feb 2, 2011
I'm trying to get an MBR1000 Cradlepoint 4G router working, but every time I plug the 4G aircard in, the router constantly resets itself about every 10 seconds or so. If I take the aircard out, the router is fine (of course doesn't have internet connection), and I can plug the card into a PC and it works fine. I talked to Verizon, and they told me that the air card that we DID have wouldn't work with a router, so they exchanged it and gave us a newer one. The 4G card is the Pantech UML290. I've tried everything I can think of, including updating the firmware on the router (and the router's 4G firmware), I've reset the router to default settings in case a setting got messed up.The guy at Verizon told me that I should basically be able to plug it in and have it work.
View 1 Replies
View Related
Dec 22, 2011
I work for a company and I am currently trying to make some changes to the security on our NAS drive, (I will give specifics of the equipment we are using below). The NAS drive we have does have some security functionality on it however we don't have the username and password (it was set up before I arrived and now no one knows anything about it). I am able to restore the NAS to factory settings which apparently will not affect the content of the drive however it will in addition to resetting the password and username, reset the IP address.Now the concern I have is that once I have reset this, then will the computers which are connected to it be no longer able to access the drive which is essential for the business.
The NAS is connected to a switch which then feeds off via Ethernet to 8 separate computers (6 running XP, 2 running Windows 7), will this mean that when the IP address is reset the computers will lose access to the drive or will they be okay as they are still connected via Ethernet. If they will lose access what will I need to do to 'reconnect' them. [code]
View 3 Replies
View Related
Aug 28, 2011
For the past 3 days, my connection to the internet has been resetting itself. I get the following message: The connection to the server was reset while the page was loading.
* The site could be temporarily unavailable or too busy. Please try again in a few minutes.
* If you are unable to load any pages, check your computer's network connection.
* If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the web.
Now, this happens with only certain sites. The sites it mainly happens to are Playlist.com, MyYearbook.com, and Vampirefreaks.com. I can be on youtube and facebook, and it will be perfectly fine. But once I go to one of the other 3 sites, I get that message, and it completely makes me incapable of browsing the web. I'm forced to close out of everything, and wait at least 5-10 minutes. I've looked around seeing what could be the problem. I've deleted cookies, cache, temporary internet files. I've made sure Firefox was permitted to access the web; used a different browser. I even did system restoration, but all it did was take me back exactly 3 days ago, when the problem first began.I use a lap top, called Asus. It's a 64-bit, Windows 7 operated. I connect to my parents' internet. Our service provider is Comcast. We called them to see if they were having a problem and they said no, everything was perfectly fine on their end; and they refreshed the modem.
View 1 Replies
View Related
Jun 6, 2012
How do you resett an IP address for Win 7
View 1 Replies
View Related
Mar 21, 2011
I just got Charter cable internet and decided to purchase my own cable modem instead of paying 5 dollars a month to rent one. I got a D-Link DCM-201. I know it is a little old but it was brand new/unused so I figured it would work out well. Ever since we got it hooked up every few hours we lose internet connectivity. The power, cable, and status lights are solid green and the Ethernet light is blinking green. The only fix I have found for this is to power cycle the modem. The problem is this happens about once every 4 hours...having to reset the router every few hours is making having cable internet a much more painful experience than it should be.
View 7 Replies
View Related
Jul 3, 2011
Well the model of my linksys is in the title so If you need It have a look at the title, so what I wanted to know was, what exactly does resetting my router do (be as detailed as possible) Is It hard to reset a router? and do you think that in my case resetting is necessary.
I forgot my wpa key, also my default password Is not "admin" I'm pretty sure I changed it after I got my router.
View 1 Replies
View Related
