Cisco Routers :: RV042 - VPN Tunnel Between Two Remote Locations
Jun 27, 2012
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
View 1 Replies
ADVERTISEMENT
Dec 17, 2011
I have establlished VPN tunnle between 2 locations
I can ping accros and access server resources on both LANs The problem is that from one location I can not access Internet
I can not ping by IP,when I do tracert it just reaches default gateway of this locations from other location(office) no problem
View 1 Replies
View Related
Dec 7, 2011
I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations. I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago. I can reboot both routers, and the VPN connects with no problem, but hangs up after a few hours / days (no pattern).
I am taking a hard look at the issue now, as about 1 month ago, the newest router "automatically" reset it itself back to factory settings (thus interrupting nearly everything in our network). After contacting support, we reset the router and re-configured it to our environment. It is plugged into a surge protected UPS (yep, I thought maybe a power issue caused the problem, but it's not). Then about 1 week ago, the other/older (9 month old) router lost it's configuration. again, reset it and all works. Including the VPN, but the VPN still works as it did before connects for a while, but then drops and generally I need to reboot the router to get it connected again (clicking on the Connect on either router doesn't work until after a reboot).
Also, in light of the recent "lost configurations", I turned on logging and now I'm getting TONS of emails of log activity, even when the network is idle (no users, no background jobs running).
after rebooting and no inter activity, I get this kind of log, all night long (to me it generally looks like the VPN connection resets and increments by 1... I'm taking a guess that the increment hits a limit someplace and I lose my VPN).[code]
View 6 Replies
View Related
Dec 16, 2011
how to establish tunnel between rvs 4000 and rv042 ?
View 2 Replies
View Related
Dec 14, 2011
here's my setup :
office 1 :
rv042 hw3
ISP:Obtain an IP automatically
office 2 :
rv042 hw3
ISP:PPPoE
VPN tunnel between both rv042, everything's fine but when i try to ssh from office 2 to an office 1's server, my connection drops.
When it drops, i can still ping pc in office 1, this is really strange!if i change the office 2 ISP to another provider (obtain an IP automatically) everything's ok !
i try to use another PPPoE ISP for office 2 and it's doing the same thing!I've also tried other rv042 in both locations with the same setup and it's doing the same thing, so it's not a router issue.
i've tried older firmware and it's doing the same thing, so it's not a firmware issue!
View 3 Replies
View Related
Aug 5, 2011
We have 4 RV 042 routers and cisco router at HQ, we have Site to Site VPN tunnels in between, All branch offices are connected to HQ via S2S VPN tunnels
10.10.1.0/ 24 HQ
10.10.2.0/24 Branch 1
10.10.3.0/24 Branch 2
10.10.4.0/24 Branch 3
10.10.5.0/24 Branch 4
now lets say i am branch 1, i can access 10.10.1.0/24 network but cant access 10.10.5.0/24 network, means i dont have branch to branch connection, it should be through HQ, means my RV042 at brnach should fwd all traffic to HQ for another branches also. Under VPN tunnel if i try to configure remote destination 10.10.0.0/21 its not allowing me it says network overlaping with local network, how i can sole it, I know how to do in cisco, we can permit those networks in access lists.
View 1 Replies
View Related
Sep 15, 2011
I was hoping that the latest firmware would fix my (2) 'bugs', but it did not. We are using the RV042s at our remote medical clinics as an end-point VPN router to our Nortel 1700 VPN router, replacing our old Nortel Contivity 100s.When I try and do a reset when connected remotely via the WAN interface, the RV042 hangs and will only reset by re-powering.
View 1 Replies
View Related
Feb 18, 2013
I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:
- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
How can I troubleshot this slow performance?
View 2 Replies
View Related
May 23, 2011
Firewall ASA5510. I'm planning to get one of ASA5510 for our office in order to secure our network properly, however we have quite specific routing configuration to allow us failover to the remote location (data center) in case of any disaster with our server. I'd like to find out if I can just install firewall between our ISP Ruter and internet and allow traffic to/from Data Centre. In this situation will I have to change routing configuration on Company Router or do I have to do anything with our Company Router
View 1 Replies
View Related
Sep 13, 2011
I configured ASA5520 and RV042 for site-to-site IPSec VPN tunnel.Tunnel get connected, but no ping, no traffic between both end network.
Network:
=======
192.168.113.0/24----------192.168.113.6 -ASA--------public, static IP address------Cisco 2821--------Internet
192.168.10.0/24-----------192.168.10.1 -RV042-----public, static IP address------Cisco 2821--------Internet
ASA5520 config:
----------------------
name 192.168.10.0 VPN
!
interface GigabitEthernet0/1
nameif NET
security-level 100
ip address 192.168.113.6 255.255.255.0
[code]....
View 5 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
Oct 3, 2012
I am not a ASA expert but I have configured them few times. I have a vision of a task I have to complete but not sure if it is practical or how to go about doing it.
We two locations, Location A and Location B. Both locations have a 100MB internet conection. Location A has a ASA 5510. Location B has a 5505. Users at both locations access the internet via their respective ASA. Location A is the headquarters and Location B is a disaster recovery site. We want to setup a tunnel between both ASAs. This tunnel will be used to replicate data between the two locations for DR purposes. We need the users to still use the same pipe to get to the internet but want to allocate 10MB for internet use and the remaining 90MB for the DR tunnel.
View 30 Replies
View Related
Apr 11, 2013
I have a brand new RV042 v3 that I just updated to the latest firmware (v4.2.1.02) and have stumbled across an anomaly... I can only access the router from the WAN port using port 80. I happen to have it set to port 8080, but that doesn't work; I have to use standard port 80.
I have two other RV042 units running older firmware and they work as expected and follow the port that is filled in. This one has me puzzled and wondering if this is a bug in the firmware.
View 2 Replies
View Related
Feb 27, 2013
I recently replaced a Netgear router with a RV042 because I figured out my Netgear was choking my 24MB Uverse connection down to about 6MB. I had VPN setup with my business partner who was already using an RV042 and everyting works fine. However after I setup the RV042 on my side we have not been able to get the VPN up. The settings are as follows
Local Group
Local Security Gateway Type: IP Only
Local Security Group Type : Subnet
IP Address: 192.168.0.0
Subnet: 255.255.255.0
Remote Group
Remote Security Gateway Type: IP Only
remote Security Group Type : Subnet
IP Address: 10.0.0.0
[Code]....
View 1 Replies
View Related
Dec 5, 2011
I have 2 dual ASA 5520 devices running VPN at two geographically different locations. What is the best way to do failover between the two remote locations?i.e. can Cisco GSS / Cisco CSM/ACE be used and if so how would this work.
View 3 Replies
View Related
Nov 24, 2011
i was connected to my rv042 via remote management / browser, and tried to add vpn clients. i generated a new certificate and then i clicked on export for clients. by doing this, the remote management disconnected and i cannot access the router anymore.
how can i get the new .pem file from remote? do i have to make somebody turn off and on the unit to get back remote access??
p.s.: after turning off an on i tried the same steps again: everytime i click on "export for admin" or "export for client", this kills the remote management and the unit must be hardreset. now: how do i get the newly created client certificate off that unit ?? otherwise i will have to drive 350 km just to grep that file ?!?!
View 1 Replies
View Related
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
View Related
Aug 28, 2011
My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies
View Related
Apr 28, 2012
I'm dessigning a network and this is my scenario:
5 - Remote sites (no static IP there)
3 - Remote users (comercial)
1 - Central building (using static ip address)
Is it possible to establish a permanent vpn tunnel between each one of my remote sites to the main building, even if I have no static IP address in the remote sites?
Do you think that RV180 is the best choice to mannage vpn connection between remote sites and the central building securely and faster?
View 2 Replies
View Related
Feb 23, 2012
I have setup a site-to-site VPN tunnel between 2 sites using CISCO rv120w.Everything works fine; any PC on one site can access all systems on the other site and vice-versa.The issue I have is when I start a VPN connection another site on Internet using IPSecuritas.I can initiate a VPN to site 1 and site 2; but when connected, I can only access servers that are located into the same site I'm connected to; I cannot ping the remote site.The Range of IP addresses on the internet during my tests is 192.168.11.0 (I 'm using a Mac)
-Systems with IP 192.168.1.1 and 192.168.10.1 are bridges
-Systems with IP 192.168.1.2 and 192.168.10.2 are CISCO rv120w
View 4 Replies
View Related
Jul 21, 2011
I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
View 1 Replies
View Related
Aug 18, 2012
I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
View 4 Replies
View Related
Sep 11, 2012
I've been looking into posibilities for extending a DMVPN (already implemented) with very small (1-2 user) remote locations over a single ISP link.I would like to use what is basically the smallest Cisco router that supports DMVPN and EIGRP (stub) - here's a sample configuration:I know that the 881 can accomplish the above without issues (if it has Adv IP Services as licensing).I would like to know if I can use the smaller routers (physically smaller, that is) for a similar configuration. Can the Cisco 819 router.URL provide the same functionality? What about the Cisco 866VAE router URl.
View 1 Replies
View Related
Jan 28, 2012
Has a small home network in 2 buildings with 2 wireless routers. He has fiber from the building where the dsl comes into, running up to his house where a second wireless modem is. Both are broadcasting DHCP but I only want one of them to do this. Ultimately I want his server(2008) to broadcast DHCP, but just one of the modems is fine for now.
View 1 Replies
View Related
May 1, 2012
I know how to connect 2 routers in 2diffrent states using internet.Also which service is used for that purpuse
View 1 Replies
View Related
Jun 28, 2011
I have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies
View Related
Jun 21, 2011
I work as a systems administrator for a global company and currently right now all my end users which is roughly 300 all use VPN from there office location to dial back into the server or use terminal server. I would like to know how to connect there locations back to main site without using VPN. What would be the cheapest and or easiest method to complete this.
View 1 Replies
View Related
Jul 5, 2012
we are trying to establish VPN tunnel between ASA5550 and RV042. The tunnel is connected but I cannot access any resources that are behind ASA5550. I can ping the servers but that is about it.
View 1 Replies
View Related
Oct 16, 2011
I have VPN Gateway to Gateway VPN tunnels set from my central office to four remote sites. The tunnels have always been problematic. Started out with five Linksys RV042 v2 devices these had problems with handshake, sometimes would disconnect during this process and had to click disconnect button on either device and this wouold force the tunnel to rebuild. Recently upgrade central device to a Cisco RV042 v3 device. Good news is that this seems to have corrected the handshake issue but now each of the remote sites are having problems during periods of inactivity losing tunnel. The staff at the remote site indicate that they have to close out application and restart router to rebuild the tunnel.
All tunnels are Gateway to Gateway static IP addresses. They all will connect and behave as expected until they reach a certian period of inactivity. I have searched all over Cisco, Linksys, and Google have seen problems similar but no consistant or logical solutions so I thought since I am slowly upgrading my network from my initial equipment which was truely purchased based on cost alone to adding more Cisco equipment. However since this is among the first of my upgrade moves and the improved equipment is creating more problems than my older less expensive equipment I needed a solution to the problem before submitting additional PO's to upgrade switches and firewall products.
View 2 Replies
View Related
Jun 6, 2011
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
View 1 Replies
View Related
Nov 27, 2012
I don't know if this is in the right section, but I cannot set up a vpn tunnel between an asa 5510 and a cisco rv042 router. I believe the problem is because i need to set up a nat exempt rule on the rv042 route but don't know how.
View 1 Replies
View Related
Sep 13, 2012
configure ip-sec vpn tunnel between ASA5525x and RV042
View 5 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
