Cisco Firewall :: 5510 - VPN Tunnel Between Two Locations
May 23, 2011
Firewall ASA5510. I'm planning to get one of ASA5510 for our office in order to secure our network properly, however we have quite specific routing configuration to allow us failover to the remote location (data center) in case of any disaster with our server. I'd like to find out if I can just install firewall between our ISP Ruter and internet and allow traffic to/from Data Centre. In this situation will I have to change routing configuration on Company Router or do I have to do anything with our Company Router
View 1 Replies
ADVERTISEMENT
Oct 3, 2012
I am not a ASA expert but I have configured them few times. I have a vision of a task I have to complete but not sure if it is practical or how to go about doing it.
We two locations, Location A and Location B. Both locations have a 100MB internet conection. Location A has a ASA 5510. Location B has a 5505. Users at both locations access the internet via their respective ASA. Location A is the headquarters and Location B is a disaster recovery site. We want to setup a tunnel between both ASAs. This tunnel will be used to replicate data between the two locations for DR purposes. We need the users to still use the same pipe to get to the internet but want to allocate 10MB for internet use and the remaining 90MB for the DR tunnel.
View 30 Replies
View Related
Dec 17, 2011
I have establlished VPN tunnle between 2 locations
I can ping accros and access server resources on both LANs The problem is that from one location I can not access Internet
I can not ping by IP,when I do tracert it just reaches default gateway of this locations from other location(office) no problem
View 1 Replies
View Related
Jun 27, 2012
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
View 1 Replies
View Related
Dec 7, 2011
I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations. I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago. I can reboot both routers, and the VPN connects with no problem, but hangs up after a few hours / days (no pattern).
I am taking a hard look at the issue now, as about 1 month ago, the newest router "automatically" reset it itself back to factory settings (thus interrupting nearly everything in our network). After contacting support, we reset the router and re-configured it to our environment. It is plugged into a surge protected UPS (yep, I thought maybe a power issue caused the problem, but it's not). Then about 1 week ago, the other/older (9 month old) router lost it's configuration. again, reset it and all works. Including the VPN, but the VPN still works as it did before connects for a while, but then drops and generally I need to reboot the router to get it connected again (clicking on the Connect on either router doesn't work until after a reboot).
Also, in light of the recent "lost configurations", I turned on logging and now I'm getting TONS of emails of log activity, even when the network is idle (no users, no background jobs running).
after rebooting and no inter activity, I get this kind of log, all night long (to me it generally looks like the VPN connection resets and increments by 1... I'm taking a guess that the increment hits a limit someplace and I lose my VPN).[code]
View 6 Replies
View Related
Mar 22, 2011
We are facing a major issue of VPN tunnel going down very often. I have 7 Site-2-Site VPN connectivity, this works fine for some days and suddently VPN tunnel goes down intermettenly for one or few locations and i need to clear isakmp sa for that speicific tunnel to come up.When tunnel goes down the vpn phase 1 status.....
6 IKE Peer: 125.18.0.38
Type : L2L Role : initiator
Rekey : yes State : MM_ACTIVE_REKEY
7 IKE Peer: 125.18.0.38
Type : L2L Role : responder
Rekey : no State : MM_REKEY_DONE_H2
After clearing phase 1 for specific tunnel the VPN tunnel come up.
7 IKE Peer: 125.18.0.38 Type : L2L Role : responder Rekey : no State : MM_ACTIVE
CINBLR01-SQDR-FIREWALL-00002# sh version
Cisco Adaptive Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)
Compiled on Thu 07-Aug-08 20:53 by buildersSystem image file is "disk0:/asa804-k8.bin"Config file at boot was "startup-config"
CINBLR01-SQDR-FIREWALL-00002 up 1 day 17 hours
Hardware: ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHzInternal ATA Compact Flash, 256MBBIOS Flash M50FW080 @ 0xffe00000, 1024KB
[code]....
This platform has an ASA 5510 Security Plus license.
View 7 Replies
View Related
Nov 1, 2011
I'm setting up two separate 5510's at two seperate locations. The client wants two seperate SSL-VPN's; one for the HQ and one for the COLO location. They have a single domain for which I have added a-records to point to the corrosponding ASA's thusly: [code]
My questions is this: do i need to buy seperate certificates for each ASA/fqdn/IP combo? I'm using godaddy to buy the certs. If I do need to buy seperate certs, that makes the installation easier, but may waste $$. If I only need to buy one cert, how do I set it up so that both combo's are verified?
View 2 Replies
View Related
Nov 27, 2012
I don't know if this is in the right section, but I cannot set up a vpn tunnel between an asa 5510 and a cisco rv042 router. I believe the problem is because i need to set up a nat exempt rule on the rv042 route but don't know how.
View 1 Replies
View Related
May 15, 2013
I have our main site using a Cisco 5510 running 8.4.2 code and a remote site using a Cisco 5505 running 8.4.2 code. The main site has a T1 and the remote site is using a DSL connection. About every other day I have to reset the connection at the remote site. The process that I have found that works is to remove the nat statement, clear the cry ips sa and then add back the nat statement. The connection usually comes back up and a few minutes. I am trying to see what is causing this to drop.
View 5 Replies
View Related
May 9, 2013
I have an ASA 5510 and I am building a site-to-site vpn tunnel, peer on the other end is a sonicwall. I can initiate the tunnel from my end, but when he tries from his end it fails on phase 2 with this error in the logs:
"Rejecting IPSec tunnel: no matching crypto map entry for remote proxy"
Obviously our crypto map's don't match, i have it restricted to specific ports on my end and he had it wide open on his end, but said he is not sure how to restrict it down to specific ports. My question is why would I be able to bring the tunnel up on my end if the crypto map's don't match and he can't bring it up?
View 5 Replies
View Related
Dec 5, 2012
I have an ASA 5510 and I am building a site-to-site vpn tunnel, peer on the other end is a sonicwall. I can initiate the tunnel from my end, but when he tries from his end it fails on phase 2 with this error in the logs:
"Rejecting IPSec tunnel: no matching crypto map entry for remote proxy"
Obviously our crypto map's don't match, i have it restricted to specific ports on my end and he had it wide open on his end, but said he is not sure how to restrict it down to specific ports. My question is why would I be able to bring the tunnel up on my end if the crypto map's don't match and he can't bring it up?
View 1 Replies
View Related
Jun 11, 2012
I working on a security solution using ASA firewall. Is it possible to setup a IPSec tunnels on each subinterface of a physical interface on ASA 5510?
View 3 Replies
View Related
Oct 24, 2012
I have a dynamic VPN site to site between a Firewall ASA 5510 with ASA version 8.2(1) (firewall ASA have a Static IP 201.111.14.114) and a C870 ISR (the ISR have a dynamic IP). The tunnel and the conectivity in both sides is successfull, however each time that occurs a interface restart because the Internet link is unstable in ISR side the VPN tunnel does not going to UP STATE again
These are the ISR logs listed when VPN going to DOWN
*Mar 10 13:58:45.157: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 10 13:58:46.157: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
[Code]......
View 2 Replies
View Related
Jul 19, 2011
So I've run into a problem on my ASA5510, post-upgrade I can no longer connect to the inside interface from across our L2L VPN. I've tried both ASDM and SSH and the connections fail. I see in the logs that the attempt is being made, but it will eventually time out. There have been no problems with this type of connection with any previous upgrades, just this particular upgrade, I went from 8.4(1) to 8.4(2). I don't see much in the release notes or anything in a pre/post config diff that jumps out as a cause to this behavior. The only thing I did see in the release notes "CSCtg50770 Mngt-access (ASDM,SSH) to inside intf of 5580 fails over RA VPN session" which sounds like it could be my problem, but that was in the "Fixed in 8.4(2)" section and says it's for a 5580, maybe the fix for the 5580 broke it on a 5510??? I hope not and that I'm simply missing some new setting that I need to enable for this type of connection as this device is in a remote office.
View 2 Replies
View Related
Nov 22, 2011
How would I go about configuring RADIUS based AAA for remote access VPN users? I have an OSX RADIUS server and an ASA 5510
(I want to keep console and SSH using LOCAL, so I keep this: "aaa authentication ssh console LOCAL", right?)What does the rest of the config look like to get RADIUS based AAA for remote access VPN users?
View 4 Replies
View Related
Apr 17, 2013
We installed a new ASA 5515 about a month ago for the corporate office we also have 40 branch locations that feedback VOIP, camera, and Citrix to the corp location. Each of the branch locations have a separate DSL connection with a local provider and all of them are dynamic IP addresses.
The problem I have is that I cannot figure out a access rule to make the voip traffic work 100% of the time what ends up happening is five or six random locations change IP address's every day and I could not figure out how to create a access rule for that so I create a static route with that dynamic IP and then it will change a week or so later. That's a horrible security risk and a lot of manual work.
View 4 Replies
View Related
May 28, 2012
I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host. How can I set this up?
View 33 Replies
View Related
Jun 11, 2013
We currently run dual ASA 5510's in A/S config on our main campus. We would like to create a VPN tunnel to a branch campus. Trying to decide between a 5505/5510/5512x, We would like to extend many of the capabilities of our network to the branch campus which will be 20-50 users on a 50mb/10mb internet connection.
Domain login
System Center workstation management
Cisco WCS
Shoretel voip
(Cisco NAC?)
Several different VLANs for wireless guest, student traffic, staff traffic, voip traffic, etc. Which device would be best and should we get the security plus license with it?
View 4 Replies
View Related
May 2, 2012
I have two 5510's that I am trying to get a tunnel established. One has an exsistinig tunnel to a 5505 that works but I cant get the next one to get past the first phase. I have sanitized the attached configs
View 5 Replies
View Related
May 30, 2012
I had a pix that had two working tunnels going to one 5510 and one 5520. Today the VPN tunnel to our 5520 stopped working but if I do sh cry isa sa both tunnels have QM_IDLE as the state. (both ends) I tried to debug crypto isakmp 255 but all I get is PEER_REAPER_TIMER and no other output on the pix side.
View 20 Replies
View Related
Dec 12, 2011
I am using a Cisco ASA 5510. Our tunnels always drop due to inactivity, which is a security issue I understand, and it only takes some "interesting traffic" to bring it back up. My problem is that it looks like the interesting traffic has to originate from my side of the tunnel, when our clients send traffic and the tunnel is down due to inactivity it does not come back up. Is there a setting that I am overlooking that will make it come back up no matter who sends traffic? Or, is there a way to make it stay up through inactivity?
View 4 Replies
View Related
Apr 25, 2013
I have been struggling to come up with the proper config to do a NAT of an incoming VPN tunnel to a VLAN on my network. I have an ASA 5510 with an IPSEC site-to-site tunnel to a partner network of 166.110.0.0/17.I have several VLANs on the ASA interface behind a cat4500 router (192.168.100.024, 172.16.4.0/24, 166.110.128.0/22 etc). The only network that the partner network sees is the 166.110.128.0/22.My problem is that I need to give them access to a node on my 192.168.100.0/24 net, but can't get the admin on the other side to add a route and adjust his tunnel.
View 4 Replies
View Related
Dec 5, 2010
I've a asa 5510 on the main site and different ASA 5505 on secundary sites for VPN tunneling between the sites. The problem is that the tunnels are acomplished but no traffic is going over them. What am i doing wrong? For the moment there is a ASA 5505 on the main site managing the tunnels but I want the 5510 to take over the job.
View 5 Replies
View Related
Mar 5, 2012
I'm attempting to debug an ipsec tunnel on an ASA 5510 (8.4(3)) and when I turn on `debug crypto ipsec` and then execute `logging monitor` I get an constant stream of TCP debugging events, is it possible to only view ipsec messages?
View 2 Replies
View Related
Nov 7, 2012
I have an ASA 5510 at V8.2(5) with something near 20 site to site VPN tunnels. I am having a problem with 1 tunnel to a RVS4000. The tunnel is completely closed and reset during Phase2. Here is a small snipet at the time of the tunnel reset
x.x.x.x, Username = x.x.x.x, IP = x.x.x.x, Session disconnected. Session Type: IPsec, Duration: 7h:36m:30s, Bytes xmt: 333755, Bytes rcv: 86281, Reason: User Requested
Followed by Group = x.x.x.x, IP = x.x.x.x, Active unit receives a centry expired event for remote peer x.x.x.x.
We use a number of connection oriented sessions and this blowing them out of the water. all other tunnels are up for DAYS to more than a Month.
View 8 Replies
View Related
Jun 8, 2011
I got a stange vpn problem, just added a new vpn tunnel to our ASA5510 and then the users report that the traffic through the tunnel is very slow, when I try it myself I get a speed like 50kb/sec to the internal server.If I use our regular tunnel or any other tunnel the speed is just fine. I´ve added the new tunnel in the same way as the other tunnels, that is thorugh ASDM vpn wizzard.
View 2 Replies
View Related
May 13, 2011
I would like to ask some question about VPN clinet and SSL VPN, on my ASA 5510 i have many tunnel-group it have around 5 tunnel-group and i have one SSL VPN,i also have user 20 user. let me show you that:
1- tunnel-group Staff-VPN remote-access
2- tunnel-group Manager-VPN remote-access
3- tunnel-group normalstaff-VPN remote-access
4- tunnel-group guest-VPN remote-access
5- tunnel-group other-VPN remote-access
and tunnel-group sslgroup type remote-access
and i have user around 20 user and i want to specific user to tunnel-groups like this
1- tunnel-group Staff-VPN remote-access
username AAA password AAA
username AAA01 password AA01
2- tunnel-group Manager-VPN remote-access
username BBB password BBB
username BBB01 password BBB01
3- tunnel-group normalstaff-VPN remote-access
username CCC password CCC
username CCC01 password CCC01
5- tunnel-group other-VPN remote-access
username DDD password DDD
username DDD01 password DDD01
So, How can i manag tunel-groups with user?
View 3 Replies
View Related
Mar 31, 2012
We are using a 5510 and have issues trying to use VPN with full tunnel to connect from inside the firewall to a customer site. I don't seem to have a problem when using split tunnel profiles. How would you troubleshoot this?
View 12 Replies
View Related
Jul 31, 2012
I have a 5510 and a 5505 that I'm attempting to configure a simple VPN tunnel over. I have tried step by step configurations form CISCO ASA configs, as well as every source I can find. I have walked throught the config with IOS commands as well as Wizards. All my packets are dropped at the the inside or outside interface.
When I show SH ISAKMP command all I get are 0's straight down.
View 7 Replies
View Related
Nov 5, 2011
I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works.
When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows;
[code]...
View 14 Replies
View Related
Apr 3, 2011
I have 2 Cisco 871 set up to vpn in to an ASA 5510. Everything has worked even when the 871 is behind a nat.
We use these routers to send to employees home for temporary use.
The WAN ports on the 871 are configured to pick up an IP via DHCP.
Office ASA 5510 - Public IP address
WAN - Public IP
Internal - 192.168.1.0/24
|
Internet
|
Home Router
WAN - Public IP
Internal - 192.168.1.0/24
|
Cisco 871 picks up 192.168.1.x on WAN port from user's home router
Internal vlan1 192.168.10.x/24
The problem is - this user's home router is using the same subnet as the internal network at the office. Is there anyway to force traffic bound for 192.168.1.x to go over the VPN tunnel? It does this correctly if the 871's WAN port is not also on the same subnet. The vpn tunnel does come up. And I can ping to and from the router, it's just the clients behind the 871 that cannot ping or access the corp network.
View 2 Replies
View Related
Apr 18, 2012
We have a ASA 5510 (v8.2.2 with ASDM 6..4.7, 256Mb mem) with a license for 250 VPN Peers. The machine has currently one site-to-site VPN active. I've added a remote-access IPSec VPN for some users but when connecting from the remote site the connection is dropped and the ASA reports %ASA-4-713239 Tunnel Rejected : The maximum tunnel count allowed has been reached.
I've searched for info relating to this message but I found none. Before I plan a restart (it's up for 222 days), is there something I could do on CLI to fix this ?
View 4 Replies
View Related
Mar 29, 2012
I have an ipsec tunnel IP is changing from mythical 200.200.200.182 to 200.200.200.254. Is it possible to change the .182 ip in below config via the CLI to .254 and have the site-to-site vpn continue to work? [code]
View 1 Replies
View Related
