I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 RepliesI have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View RelatedSo here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies View RelatedI have RV042 Router, I'm using only one Internet conection, I'm using IP group like this 192.168.95.x, my DHCP setting use 192.168.95.120 to 192.168.95.240, but in this time I have 245 workstations (may be I will have 25 additionals workstations) and some times I see IP conflict message in my current work stations.
I had read about SUBNET like response about my problem, but I'm not sure about that and how to make subnet with my RV042.
We connected to locations to the RV042 by setting up 2 Gateway - to - Gateway VPNs - both locations can communicate with the RV042 and devices within the local LAN of the RV042 - however at the moment it is not possible to send traffic from 1st VPN Location to the 2nd VPN location
View 1 Replies View RelatedI have a RV042 with multiple subnet, 192.168.10.0 and 192.168.9.0. 192.168.10.0 is assigned to the LAN, 192.168.9.0 is created under multiple subnet. Both subnet can access Internet by accessing IP address, but 192.168.9.0 cannot access Internet by using host name. It looks like DNS is not working for the 9.0 network.
View 1 Replies View RelatedSmall office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
Breakdown:
DSL 1
|
RV042
|
192.168.20.X
|| Would like to somehow join the 2 networks together.|
DSL 2
|
RV042
|
192.168.40.X
I'd like to set each individual LAN port with different address i.e. LAN 1 192.168.1.1 and LAN 2 10.1.1.1 instead of using the multiple subnet feature and having all ports replying for the addresses created.
View 3 Replies View Relatedmy RV042 is not able to propperly update my ddns. If you try to resolve my dyndns subnet kitus-network.dyndns.org you will get 192.168.0.2. How can I make the router update my ddns with the real public ip rather than the private ip it "sees" on the WAN interface?
View 5 Replies View RelatedI have 2 questions to confirm and/or get direction on how to modify.
1) is there a way to get around the (seemingly arbitrary) class C (slash 24+) subnet restriction for the primary/main IP address for the internal LAN?
(I realize I can setup multiple internal subnets but that also seems to introduce restrictions for port ‘forwarding’ and ‘one-to-one NAT’ use because those features seem to be restricted to the primary/main IP subnet)
2) it seems like all traffic is passed to the host on the internal side of a ‘One-to-One NAT’ regardeless of the firewall rules in place, is that what is be expected?
I am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.
View 1 Replies View RelatedI know this *should* be simple but having a devil of a time getting it to work.
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10
[Code].....
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.
I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
View 4 Replies View Relatedi cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies View RelatedI have two offices connected with an IPSEC VPN tunnel using RV220W routers. The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x). I have also set up PPTP users for remote access. PPTP users that connect to site 1 cannot access site 2 and vice versa. The PPTP users have no trouble accessing the resources on the site that they connect to. I have tried activating RIP and adding various static routes with no success. If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.
View 2 Replies View RelatedI would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?
View 1 Replies View RelatedI have been trying to resolve this issue with only allow facebook access throug the content filter between 12pm and 1 pm. However The settings never seem to take. Is this a bug in the system? If I start the filtering from 1300 to 1200 that should allow facebook to be accessible only on lunch.
View 2 Replies View RelatedI am trying to access my RV042 through telnet. I go to http://192.168.1.1/sysinfo123.htm?ConsoleSimulation=1
which enables telnet. However when I type my username and password it will not authenticate.
I am new to implementing VPN service. What I would like to do is install a RV042 or RV082 (for added speed) and configure it to allow me to access the Internet (from home base) through the VPN from any location while on the road and using my laptop. My questions are: Can this be done? If so, what needs to be done in the configuration to allow gateway access to the Internet? I can't find any reference in the Cicso documents, but somewhere I saw that it can be done. I don't care about accessing anything on the local LAN. As I would be using the same Internet connection for the VPN and the access to get out----how would this affect speed? I plan to use Quick VPN as the client, and haven't even touched the client issue.
View 5 Replies View RelatedI had this problem where 2 users could only access my RV042 vpn one at a time
The Linksys solution was to give these 2 users a RV042 as well. That worked, 2 can access my vpn at the same time. We use QuickVPN for this purpose
But now there users cannot access another Cisco vpn any more in our office. I attach a schematic and a screen shot of the error when trying to connect to the professional vpn with vpn client version 5.0.07.290
The 2 notebooks epresent the 2 users
The one at the bottom is my vpn
The connection on the left is the professional vpn
We now use remote desktop to my vpn to get to the professional vpn, that work but we don't like it
I configure my new purchase RV042 router, in Access Rule i Deny all services the source is Lan and destination is WAN. my concern is i want to allow LAN to access internet, so i'ved create another rule which allow http, https. but my problem is i cannot access internet.
View 4 Replies View Relatedbrand new RV042 client (tried MacOS and Win7 on two laptops) will get IP from DHCP and shows correct IPs for gateway etc. - however entering the IP 192.168.1.1 to access web admin does not work (tried current versions of Firefox, safari and Firefox); browser is not offline router was reset to factory setting (by pressing reset for over 30sec) ping on IP above works
hardware broken?
I've setup a GroupVPN and connect to the RV042 with the Shrewsoft VPN client, works like a charm as opposed to QuickVPN ;-)The firewall is configured with an explicit deny rule for RDP access to an internal server, also an explicit allow rule is created for certain IP numbers as source. I noticed that I need to create an explicit allow rule for the subnet the Shrewsoft client is using for the virtual adapter or I will not be able to access the internal server via RDP through the GroupVPN tunnel. I would think that setting up a tunnel defies the rules created for direct access on the WAN port.
View 5 Replies View RelatedI am trying to setup a VPN using an RV042 (fw ver: 1.3.12.6) to access a VISTA computer over the internet using a laptop using QVPN's latest version. I finally got it to connect but then hang's with error " Gateway is not responding, do you want to wait?". If I say yes it go through the login again and hangs. If I say no, it hangsup. I've tried a couple different ideas using tunnelling and static IPs in the router but nothing. All I want is to be able to access one computer through the RV042 over the internet from any other computer using the QVPN.
View 6 Replies View RelatedVery recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
I am trying to limit HTTP access to my server on the local network to a specific IP address. I create an Access Rule in the firewall section, however that doesn't work. The only way it works is if I add the internal IP address of the server to the Forwarding section where I create a new HTTP forwarding rule.However, that is not good because that allows ALL HTTP traffic to that server instead of just by the single IP address.
View 2 Replies View RelatedI've installed RV042 for a client of mine. For next two months everything worked without any problems. The issue I've been experiencing lately is when I assign a static IP address to the PC it won't have internet access. Once I allow it to have a dynamically assigned IP then it works fine. The IP I assign isn't part of the DHCP range.
View 7 Replies View RelatedI wanna block the Lan IP address(eg:192.168.2.106) to visit wan web, and allow it to lan.How can i set it in access rules?
View 2 Replies View RelatedI have 2 VLANs set up and I know they are set as default to not allow one to communicate to the other. Is there a way to set a rule to allow that? I'd like VLAN1 to be able to access VLAN2, but not the other way around.
View 1 Replies View RelatedI can connect via VPN with the QVPN but once I am connected to my network I cannot view the resources available to me by LAN. I am nowhere near aware as to why.
View 4 Replies View RelatedI have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running Win XP PRo SP3.
View 1 Replies View RelatedI have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?