Cisco Routers :: Cannot View LAN Resources?
Apr 23, 2012I can connect via VPN with the QVPN but once I am connected to my network I cannot view the resources available to me by LAN. I am nowhere near aware as to why.
View 4 Replies
ADVERTISEMENT
Cisco Routers :: Access LAN Resources Through WRVS4400n?
Apr 24, 2012I am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.
View 1 Replies View RelatedCisco Routers :: RV082 Access Resources On RV016
Apr 29, 2013I know this *should* be simple but having a devil of a time getting it to work.
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10
[Code].....
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.
Cisco Routers :: Setting Up Vpn With RV 120W Cannot Access LAN Resources
Oct 12, 2011I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
View 4 Replies View RelatedCisco Routers :: RV042 - VPN Access Resources With Same Subnet?
Aug 24, 2011I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View RelatedCisco Routers :: RV042 - Access Site 2 Resources Via QuickVPN Connection?
Nov 15, 2010So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
Cisco Routers :: RV042 Cannot View Web Configuration
Oct 25, 2012Yesterday I have purchased a new rv042 router, If i enter url...I have access to a menu but nothing is shown when I follow the menu link.
View 6 Replies View RelatedD-Link D-ViewCam :: 3.3 / Setup 4 Cameras To View With Remote Live View?
Apr 12, 2013I am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
View 5 Replies View RelatedRouters / Switches :: Can't View Cameras On The Web?
Oct 28, 2011i have a public ip and private still my cameras are not working i can't view them on the web.
View 1 Replies View RelatedCannot View Devices On Separate Routers
Jan 27, 2012I'm having a problem viewing devices on my home network. To better explain I created this diagram of my Home Network below.I have a Cisco VPN Router and connected to that I have a Netgear WRN 1000v2 Router & Linksys WRT54G2v1 Router. I used to have my home network connected to only one router and I was able to see and connected to other devices. Now my networks are separated, I think it has something to do with subnet masking and the IP addresses on the routers.
View 6 Replies View RelatedCisco Routers :: RV082 Backup File View?
Sep 19, 2012Is there a way to view the contents of the .exp file generated from exporting the configuration from RV082? I've got a couple of RV082 that have the same rules, but want to compare the configuration.
View 2 Replies View RelatedCisco Routers :: RV082 V3 - View Configuration File?
Feb 27, 2013Currently, the backup config is not human readable...any way to convert this?
View 1 Replies View RelatedBelkin Routers :: F5D7230-4 How To View / Monitor Traffic
Jan 6, 2013I have a Belkin G router F5D7230-4 (firmware version 8.01.07) and am trying to view stats on what is using our connection.We have a very low capacity, rural wireless broadband that our ISP tells us is maxed out all the time, even when we don't appear to be using any devices, so I'd like to view the traffic on our DHCP client list to see which device is using an excessive amount of bandwith and put a limit on its access.I don't see a statistics tab on the setup page, is there another place to look or does Belkin have an external program to do this?
View 1 Replies View RelatedRouters / Switches :: Port Forward On A SAGEMCOM SE567 Router To Be Able To View DVR?
Jun 12, 2011How do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 Replies View RelatedCisco :: QoS Resources
Dec 12, 2011I got asked recently to start working on QoS for our networks. I have dealt very little with this. I ordered the Cisco Press QoS book and have been saving information from Cisco's website on this.
View 5 Replies View RelatedPc Cannot Use Resources On Other One
Jun 7, 2011I have set up a smal LAN in my home with two Windows XP PCs connected tot he Internet using a DSL connection. I have a DSL router box connected to the DSL and to a small switch. My two PCs connect to the switch. I can browse the Internet from either PC. However, I discovered that each PC cannot use the resources on the other PC. What is the problem and what do I do?
View 14 Replies View RelatedCisco WAN :: 881 VPN Can't Access Local Resources
Oct 5, 2010I have a Cisco 881 and I want to use Easy VPN.
-VLAN 1: 192.168.4.0
-WAN: 10.0.0.0
-VPN: 192.168.8.0
VPN connects and I get an IP of 192.168.8.100 from my pool. I can ping my cisco at VLAN1 (192.168.4.1), but I cannot access my local resources. I guess I miss a NAT configuration.
Can't Connect To Remote Resources Over VPN
Nov 22, 2012I have a VPN server set up behind a home router in my apartment. I'm able to connect to it from other locations, and have verified that internet traffic is going thru the connection (ipchicken.com reports the IP address of the VPN network). But I can't seem to connect to other machines on the router subnet. For example, 192.168.1.1 connects me to the local gateway rather than my apartment router. Also, I can't connect to known good static IPs for other machines on the remote subnet, including the machine I'm VPN'd thru!
Note that in connection properties, the setting to 'use remote default gateway' is checked.
Access To Network Resources?
Jun 12, 2011The Linksys is connected to a cable modem and a Dell Vostro system, the Netgear is connected via Cat 5 to the Linksys and the Linksys is the DHCP provider to the Netgear.The Vostro shares hard drives, folders and printers to the networkBoth have wireless and wired users.They are each DHCP providers to their users.How must I configure each to provide users on both routers access to all network resources
View 2 Replies View RelatedFortigate 50b / VPN - How To Access LAN Resources
Feb 9, 2011I've set up a VPN using a fortigate 50b wifi and forticlient ipsec VPN. when I log into my office from home, I cant see anything on my network at all. I can however remote desktop into other PC's and can access stuff that way. I was under the assumption that ... one a VPN connection is made in the LAN you should be able to see other pcs and servers in the workgroup. Is this not the case or do i need to configure something?
View 2 Replies View RelatedCisco VPN :: RV042 - Cannot Access Resources With Same Subnet
Aug 19, 2011I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View RelatedCisco Firewall :: ASA 5520 - How To Block LAN IP To Use WAN Resources
Nov 12, 2011I am getting to many teardown tcp connection for outside interface.
i want to block this ip using CISCO IPS or using A access-list in ASA 5520 .
Cisco VPN :: ASA5505 Can't Reach Remote Resources
Oct 13, 2011I have a (central) ASA5510 acting as a EasyVPN server and a number of (remote) ASA5505 as EasyVPN client. All the communication works fine between the different networks. The issu is the ASA itself. The remote ASA can ping the central ASA on it's internal IP-adress, but it can't ping any other resoruces at the central network. If I ping the DC at the central network from the remote ASA I get a deny in the central ASA with source address as the public IP-adress of the remote ASA and destination of the internal address of the DC. If I from the remote ASA do "ping inside ip-of-central-dc" it work's like a charm, but "ping ip-of-central-dc" dosen't work.
View 3 Replies View RelatedCisco VPN :: ASA 5505 / Cannot Access Remote Resources
May 24, 2011I have 3 networks coming from the DMZ (VPN) and only one works:10.132.24.0/24 Not working10.132.25.0/24 Not working10.132.26.0/24 Working The thing is, the one that works is on the same network as the DMZ(VPN) interface. The other two do authenticate and they get an IP from the VPN Pool. but they just cant access anything.
View 11 Replies View RelatedCisco VPN :: 5510 VPN Connects But No Local Resources
Nov 21, 2011I've got a VPN setup on an ASA 5510, it connects fine and my users, and myself are able to remote desktop, and ping. However, when accessing the servers by hostname I get nothing. When I want to access a fileshare I have to do it by IP. I've got my internal DNS added in the config.
View 3 Replies View RelatedCisco Switches :: SG 300-52 MAC VLAN No Resources For This Range
Oct 6, 2011We setup about 5 MAC based VLAN groups with about 40 MACs total and now we are getting "There are no resources for this range.." when we try to add more MACs or try to assign them to the port/VLAN "MAC-Based Groups to VLAN". We tried to reboot and use the CLI, same error. Is there some undocumented small limit on the MAC based VLAN groups?
View 2 Replies View RelatedCisco WAN :: 1841 Can't Access Network Resources
Nov 26, 2012I'm working on setting up a couple of new WAN sites with 256K frame relay circuits back to our main building. Each new site has a new PVC, and both are pointing back to a PVC on a T1 at the main building. The main site has a 2801 with a single CSU/DSU WIC, and each new site has a 1841 with a 3560 connected to fa0/1. At both sites, I'm able to get the circuit up, and the serial interfaces at both new sites show up/up, and the subinterfaces at the main site also show up/up for both sites. Routing is being done by EIGRP, and both sites are able to establish the 2801 as an EIGRP neighbor, and I'm able to ping/tracert anywhere on our network by name or IP, so routing and DNS appear to be working. I can also ping both new routers from the main site. However, that's about all I can do. I'm not able to access any resources on our network (email/shares/internet/intranet/etc) from the two new sites. I can ping the new routers/switches from the main site, but can't ssh to them. I can ssh to them locally. There are no firewalls in the equation, and I don't think there are any ACL's in the picture either.
Can ping and tracert just fine anywhere on our network (from both the 1841, a PC plugged into the 3560, or a PC plugged directly into the fa0/1 port on the 1841), including out to the internet, by name or ip.Can ssh to local router, but not to anything that isn't localDNS is workingDHCP not working using ip helper pointing to DHCP scope on server at main site, have to use static IPCan't rdp to anythingCan't get emailCan't browse windows sharesCan't get to any websites, external or intranet. IE says "Website found, waiting for reply..." but eventually times out.
I did some testing for communication over certain port numbers using telnet and nmap, and found the following:
Can telnet to url.. and local intranet webserver on port 80 (http)Can telnet to two of our Exchange Servers on port 25 (SMTP)If I run an nmap scan on url...com, or our intranet webserver, it confirms that 80 and 443 are open, but the pages will not load. I am able to telnet (port 23) to a state mainframe via the internet that some of our employees use, and I do get the expected login screen. I tried erasing the config one of the new routers, and just added back the bare minimum config to get the circuits up (serial/ethernet interface configs, eigrp), but saw the same symptoms.
One other thing to note: the 2801 at the main site has three other frame relay sites connected to it on the same WIC as the new sites, all of which are working fine.
I just don't understand why I can ping everywhere I need to be able to ping, and port scans show that communication is open over needed ports, but the applications don't work.
Cisco VPN :: 2611XM Cannot Access Remote Resources
Feb 24, 2011I am having an issue with my Cisco VPN Client. I am new to VPN setup, so this is probably something easy I am missing. I have a 2611XM router acting as my internet gateway for my local lan, and my VPN Server. I am doing all my testing from a company laptop with a mobile broadband card. The VPN will connect, but anytime I ping anything within the inside network, it comes back with the public IP of the outside interface. I have NAT overload configured so everything on the inside network can access the internet, which it looks like might be causing my problem.
When i remove the nat overload on my fa0/1 interface, the vpn will connect to any resource on the inside.
Sharing Resources Between Two Networks (3800HGV-B)
Oct 13, 2012how to share printers and folders between two different networks. My Current set up is AT&T Uverse 2Wire 3800HGV-B with a Linksys WRT320N running WRT plugged into one of the 3800's lan ports. The WRT's WAN port is plugged into the 3800 LAN port. The Ip set up is as follows:
2Wire, Inc. 3800HGV-B (My Router / Internet Connection)
192.168.1.254/24
Linksys WRT320N (Kids Router)
192.168.1.63/24 WAN
192.168.0.1/24 LAN
I use the WRT to manage the kid's Internet usage and limit their bandwidth. Everything works great EXCEPT they (192.168.0.0/24) cannot reach resources on the 192.168.1.0/24 network and I (192.168.1.0/24) cannot reach resources on the 192.168.0.0/24 network. I imagine its because the 2wire router does not know how to get to the 192.168.0.0/24 network. The configuration of the 3800 isnt very intuitive. If I could, I would just put a route in the 3800's routing table so that it knows that 192.168.0.0/24 is behind 192.168.1.63.
how to configure that 3800 to do this
Cannot Access Shared Resources On New Network
Jan 24, 2012I have two places that I work out of. One is in Romania and one in Bulgaria. In Romania, I have a small office/home network set up. It has at least 8 computers (including the three that I have with me currently - some wireless and some towers) and a couple of android phones and Ipods. I have no trouble accessing any of the computers shared folders or them accessing mine. There are a varity of operating systems used there from XP, Windows 7 and Mac.Everything works great. All the computers can access each other shared resources. All the computers are set to get IP automatically from my DLink DIR - 600 router. I have brought my three computers to Bulgaria (tower and two laptops). They are all set the same- no changes in settings. However, in Bulgaria, All three computers CAN access the internet but NOT each other.
[code]...
Cisco Firewall :: ASA 5510 / Use Of Bookmarks Of Resources Which Are Located Behind A S-to-S VPN?
Apr 16, 2013I was wondering if i can create (a) bookmark(s) of resources which are located behind a particular Site-to-Site VPN?We are using a Cisco ASA 5510 (9.0.2) with SSL VPN configured. The tunnel is up but when i try the bookmark, i get the error "server unavailable".
View 2 Replies View RelatedCisco :: LMS 4.0 Takes Lots Of Resources And Also Stops Responding
Sep 10, 2011How to fix our LMS 4.0 high CPU issues?. It takes lots of resources and also some time stop responding.
View 7 Replies View RelatedCisco Application :: Monitoring And Allocating Resources On ACE20-MOD-K9
May 16, 2012We are currently running a ACE20 with 11 contexts. Recently we have seen that one of the contexts is being 'starved' of resources, especially Concurrent Connections, Bandwidth and Throughput.
Whilst we know how to address this situation by reallocating resources from less busy contexts, I was wondering if there was a more scientific way of looking at the resources being used and calculating the best way to allocate them across the ACE other than just looking at the 'show resource usage' and 'show resource allocated' commands?
Has Cisco or any other 3rd party developed a handy tool to monitor the the ACE resources which will possibly assist with calculating the optimum resource allocations across all contexts?