Routers / Switches :: Port Forward On A SAGEMCOM SE567 Router To Be Able To View DVR?
Jun 12, 2011How do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 RepliesHow do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 RepliesI attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies View RelatedLooking to remote access my CCTV DVR, need to port forward. Set up dyndns domain already.
View 1 Replies View RelatedI cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
View 1 Replies View RelatedI recently installed a First Alert Security System and assigned IP address to the DVR but within the DHCP (After reading many threads, I will asssign, ping and create a static IP outside of the DHCP, maybe this will resolve the issue). I am able to view the cameras on my iPhone and HP Laptop but only internally on my network. I am trying to port forward my DVR IP address to be able to view the cameras on a public website. Although I am going to chcek and see if assigning an IP to my DVR outside of the DHCP and hopefully this will be it, I am afraid that my CradelPoint CRT 500 Modem will not support it. I read on one thread that this is a common issue after you have exhausted all the options. How can I be sure that my modem supports that my router port forwards? I want to avoid configuring to run in bridged or pass-through mode.
View 3 Replies View Relatedhow can i view the port G27 and G28 in GUI? As based on the GUI Adminstrator - > Port Management - > Port Setting i only can view from port G1 to G26. Or it will only appear when the port is active for stacking.
View 3 Replies View Relatedi have a public ip and private still my cameras are not working i can't view them on the web.
View 1 Replies View Relatedhow to forward ports using routers
View 2 Replies View RelatedI have two ports forwarded on my F7D4302 router, used for security cams, trying to add a third. The router does not open the third port. I've tried several different configuration without success. Since I've already been successful with the first two, I am puzzled.
View 2 Replies View RelatedRecently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
i go to setup/port forwarding and it has every port except port 22 available to forward. what's up with that?
View 1 Replies View RelatedI volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
I'm trying to setup a simple port forward in the RV 120W Router, but can't seem to get it to work.
I created a custom service called RDP for TCP port 3389-3389. I added a Port Forward to Always Allow the service RDP, from any source IP to destination IP 192.168.50.23. I have tried it with "same as incoming port" and also specified port 3389 for forward from and to.
Firewall access rule is enabled and set to Inbound, Always Allow, RDP service, Any source & destination IP, DNAT IP is 192.168.50.23.
I have a westell 7500 with fairpoint service hooked up to my DSL line. I have disabled woreless on the westell. I then have a linksys e-1000 connected to the westell 7500. I have one wired computer on that network, my imac/game server, my main PC, my wii and an ipod touch connected connected to the linksys e-1000 wirelessly. I want to forward port 25565 through these routers to my imac. How can I do this? I have tried portforward.com, and a million other things.
View 2 Replies View RelatedI have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward. Everyone else is dropped. Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.
View 1 Replies View RelatedUntil now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
View 3 Replies View RelatedI feel I'm having an issue, and I'm unsure why.We own a Cisco RV042 V03 with firmware 4.0.4.02-tm.
I have successfully demonstrated that I can open and forward ports 8001 & 8081 from the WAN side to a specific IP Address on the LAN side.I performed this by going to Setup --> Forwarding, then setup Port Range Forwarding & Port Triggering.
I also changed Setup --> UPnP, then UPnP Function is set to Yes.
My issue is that we would also like to forward 11101 through 11164 in the same maner. However, when I step through the same method described above, it does not seem to work.So now I am confused how I could open the 8001 & 8081 ports, but not the higher 11101 thru 11164 ports.
There is no support for Model F9J1005v1. How do I update its firmware and how do I port forward on the same
View 2 Replies View RelatedI'm having a problem forwarding port 1723. What i'm trying to do is to use VPN to access my server pc and I don't want to use the VPN software that is in the router. When I telnet the port it goes through but when i try to access it outside of the office I can't get through. I've been using [URL] to check port 1723 and I get this:
Error: I could not see your service on XX.XX.XX.XX on port (1723)
Reason: Connection refused
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View RelatedI have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies View RelatedI am trying to open port 12000 on my sky dlink router, been trying for a few days now and i just can't nail it. When i log into router, it brings up the sky router page, any one ever setup port 12000 on the sky router page.
View 1 Replies View RelatedISP Cable in Smart box. 4 cat 5 cables from various rooms in house to feed cable ready TV's and one from my computer room. Can I connect all cat 5's to switch that is connected to cable modem located in Smart box and connect Wireless Router to cat 5 in the computer room and expect router to work properly?
View 4 Replies View Relatedhow do I get my hard drive to work thru my belkin router usb port?
View 1 Replies View RelatedSo, brand new Inspiron n7110 lappy running Windows 7 Home Premium (64 bit). Got it home, fired it up and found that it could see the network, but refused to actually do anything with it, or even cough up a specific error message other than 'Windows was unable to connect to (networkname)'.Fiddled with it for a while, entered and re-entered the passkey, mucked about with settings, made sure that the network name and whatnot were all entered correctly, and eventually got annoyed and simply disabled security. Lo and behold, it worked beautifully... sometimes. Connectability was still badly erratic (didn't get any unplanned disconnects, but when it booted up, it was pretty much even odds as to whether or not it would connect). But as soon as I re-enabled security (WEP, in this case.I suppose I really should figure out how to get WPA to work, but one problem at a time >.<)The router is a Siemens SE567.
View 1 Replies View RelatedI have a Cisco 1841 router with the followingSerial T1 connection Fastethernet 1 with network address 192.168.0.1 Fastethernet 2 with network address 198.168.0.1I want to isolate Fastethernet 2 so that it cannot access the internet or the 192.168.0.1 network. Only incoming request is available.
View 5 Replies View RelatedCan switch do a port forward without a router just plane switch to port forward to another network crossing the internet.
View 1 Replies View Related[URL]I want to port forward so my family (not in my home) can play Minecraft on my server. What values should I type?
View 1 Replies View RelatedI have a Huawei 523a Router at the moment and I'm trying to setup a IP camera.The Router doesnt allow port forwarding, so my question is can I add another Router onto the Huawei router to allow the second one to work my camera
View 10 Replies View RelatedI have a belkin f7d4302 v1 and I can't get it to forward my ports.
View 6 Replies View RelatedI have unchecked 'Block Anonymous Internet Requests” but then also I am not able to forward ports like 80 and port 443.
View 1 Replies View RelatedI'm trying to forward ports for game connections. For this particular game, I'm trying to forward port 7777My ports aren't forwarding according to: Open Port Check Tool - Test Port Forwarding on Your Router and Open Port Check Tool[CODE]
View 13 Replies View RelatedI have my router set up and life was good. i now want to forward a port. i go into apllications/gaming put the application name, the port i want to forward and click enable. Save changes and i get a changes save message. When the browser goes back to the applications/gaming screen no port shows as being forwarded. If i go to canyouseemenow.org the port shows as being closed.
View 3 Replies View Related