I have two ports forwarded on my F7D4302 router, used for security cams, trying to add a third. The router does not open the third port. I've tried several different configuration without success. Since I've already been successful with the first two, I am puzzled.
View 2 RepliesI have a belkin f7d4302 v1 and I can't get it to forward my ports.
View 6 Replies View RelatedBelkin F7D4302 will not connect to ISP if I try to manually set DNS entry. Once I attempt this I have to reset the router back to factory defaults before the router will connect with ISP
View 4 Replies View RelatedFor some reason, wireless connections from my moms Belkin Play router #F7D4302 v1 disconnect everytime the landline phone is used! There is no phone line connected to my moms computer, modem or router
View 3 Replies View RelatedThere is no support for Model F9J1005v1. How do I update its firmware and how do I port forward on the same
View 2 Replies View RelatedI can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems
attempted to fix problems via belkin software
changed channels on modem
updated firmware
etc, etc
I have a Belkin Play N300 (part number = F7D4302) wireless router, and I want to connect my (soon-to-be-pole-mounted) 12DBI omnidirectional antenna to it, the goal is better wireless access in one area of a church camp. I have a couple of U.lf - RP-SMA pigtails on the way, because of course the router doesn't have an external antenna connection.
I opened up the router case, and below is a shot of the board. There's plenty of room inside the case. The router is dual-band (2.4 and 5ghz), and uses 2 internal antennae, apparently it senses the better one and uses it as needed.
My plan is to disconnect one antenna, and connect/solder my external antenna pigtail in its place. I'm a fair hand at soldering, but very little practice de-soldering...
1. Is disconnecting / replacing one antenna the way to go, and if so, which one? Or should I leave them both connected and piggyback my external onto one of them (soldering the leads on top of existing connections), or disconnect both antennae, or does it matter?
2. Which set of wires, white or black, are used for which band - and should I connect to? I assume I'd want to hook up to the 2.4ghz, correct?
The white wires come out from the tiny Broadcom chip, I think it's marked BCM43224KMLG (dang, that's some tiny print!). This page leads me to think that these are the 5ghz antenna leads, but I'd llike to be positive before I start cutting.
The black wires appear to feed from the larger Broadcom chip marked BCM4718A1KFBG. Again, this page leads me to think that this is the 2.4ghz antenna.
3. Assuming that the black wires are the ones I want, would it be ok to cut one really close to the board end, cut the U.fl connector off of my pigtail, prep the wire / shielding, and solder the wire / shielding on top of the existing solder connection?
I am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.
How do I forward ports on the N600 DB F9K1102v3? I have looked through everything. When I go to port forward, I enter the info and have it all down correctly, I click save and once it reloads it isn't there and the port isn't forward.
View 1 Replies View RelatedRecently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
i go to setup/port forwarding and it has every port except port 22 available to forward. what's up with that?
View 1 Replies View RelatedHow do I setup my Belkin F7D1301 with a 16 port 10/100 switch so I can use the wireless on the Belkin and have the 16 port switch for my hard wires?
View 1 Replies View RelatedLooking to remote access my CCTV DVR, need to port forward. Set up dyndns domain already.
View 1 Replies View RelatedI cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
View 1 Replies View RelatedI'm trying to setup a simple port forward in the RV 120W Router, but can't seem to get it to work.
I created a custom service called RDP for TCP port 3389-3389. I added a Port Forward to Always Allow the service RDP, from any source IP to destination IP 192.168.50.23. I have tried it with "same as incoming port" and also specified port 3389 for forward from and to.
Firewall access rule is enabled and set to Inbound, Always Allow, RDP service, Any source & destination IP, DNAT IP is 192.168.50.23.
I attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies View RelatedI have a westell 7500 with fairpoint service hooked up to my DSL line. I have disabled woreless on the westell. I then have a linksys e-1000 connected to the westell 7500. I have one wired computer on that network, my imac/game server, my main PC, my wii and an ipod touch connected connected to the linksys e-1000 wirelessly. I want to forward port 25565 through these routers to my imac. How can I do this? I have tried portforward.com, and a million other things.
View 2 Replies View RelatedI have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward. Everyone else is dropped. Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.
View 1 Replies View RelatedUntil now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
View 3 Replies View RelatedI feel I'm having an issue, and I'm unsure why.We own a Cisco RV042 V03 with firmware 4.0.4.02-tm.
I have successfully demonstrated that I can open and forward ports 8001 & 8081 from the WAN side to a specific IP Address on the LAN side.I performed this by going to Setup --> Forwarding, then setup Port Range Forwarding & Port Triggering.
I also changed Setup --> UPnP, then UPnP Function is set to Yes.
My issue is that we would also like to forward 11101 through 11164 in the same maner. However, when I step through the same method described above, it does not seem to work.So now I am confused how I could open the 8001 & 8081 ports, but not the higher 11101 thru 11164 ports.
How do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 Replies View RelatedI'm having a problem forwarding port 1723. What i'm trying to do is to use VPN to access my server pc and I don't want to use the VPN software that is in the router. When I telnet the port it goes through but when i try to access it outside of the office I can't get through. I've been using [URL] to check port 1723 and I get this:
Error: I could not see your service on XX.XX.XX.XX on port (1723)
Reason: Connection refused
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies View RelatedI need to set up port forwarding to access a security camera from my home computer. I can't get it to work on my F5D8230-4.
View 8 Replies View Relatedhow do i do port forwarding on my belkin n750 db i want to view my cams when not home i can view on my network not tmobile?
View 3 Replies View RelatedAccessing my hdd on the usbport is very slow. Have a n600 router. Can I boost this in any way?
View 2 Replies View RelatedCan any of the wired/wireless routers like the n-150 be sub-netted with each wired port being its own subnet?
View 1 Replies View RelatedRegion : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
I have one server 172.16.0.100 and i nat this server to a public ip X.X.X.5 and i open RDP for this public ip.Now when i access Remote desktop on this public ip x.x.x.5 it open perfectly.Now my senario is that i want to open a http url on port 5555,server ADMIN open port 80 for this URL on LOCAL lan(http://172.16.0.100:80)So how can i map port 5555 to port 80 on ASA 5520.so when i hit URL [URL]
View 5 Replies View RelatedI have a Belkin AC1200 Router. It seems working properly re Internet/Wireless connections. When I connect a printer (Canon Pixma MP500) through the USB port the (USB) light doesn't turn on, nor the printer is appearing on the "available devices" (Belkin USB Print and Storage Center).
View 2 Replies View RelatedIs it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View RelatedI have only recently noticed a HUGE decrease in my Utorrent speeds, so i thought i would have a gander and lo and behold.apparently the port Utorrent uses wasn't open. Now, i have tried about 10 different port numbers, made sure Utorrent is being accepted by Norton 360 Firewall,followed complicated directions to (i think) foward ports, and also follow directions to open a specific port.Nothing has worked so far, Utorrent still comes back with a port closed error.
View 1 Replies View RelatedI have just purchased a nas drive. I want to be able to access my files from anywhere. I believe if i setup FTP i can view the files over the web. from what i have been told i need to forward port 21 to the ip address of the nas drive.
View 6 Replies View Related