Cisco Routers :: RV042G Can't Forward SSL Port 443
Aug 26, 2012
Recently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
View 3 Replies
ADVERTISEMENT
Oct 12, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies
View Related
Apr 22, 2013
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
View 2 Replies
View Related
Oct 11, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
View 2 Replies
View Related
Mar 23, 2013
Each of the 2 WAN ports on my RV042G has its own dedicated public IP address. I would like to set up the router so that all incoming traffic on WAN1 is always routed to a specific server (=LAN IP), and vice versa, that particular server's outgoing. Internet traffic is always sent through WAN1.
It has to be controlled by IP address as the system in question is not directly connected to the router, there is a switch in between.
View 2 Replies
View Related
May 29, 2013
i go to setup/port forwarding and it has every port except port 22 available to forward. what's up with that?
View 1 Replies
View Related
Mar 6, 2013
I have two ports forwarded on my F7D4302 router, used for security cams, trying to add a third. The router does not open the third port. I've tried several different configuration without success. Since I've already been successful with the first two, I am puzzled.
View 2 Replies
View Related
Apr 2, 2011
Looking to remote access my CCTV DVR, need to port forward. Set up dyndns domain already.
View 1 Replies
View Related
Aug 28, 2011
I'm trying to setup a simple port forward in the RV 120W Router, but can't seem to get it to work.
I created a custom service called RDP for TCP port 3389-3389. I added a Port Forward to Always Allow the service RDP, from any source IP to destination IP 192.168.50.23. I have tried it with "same as incoming port" and also specified port 3389 for forward from and to.
Firewall access rule is enabled and set to Inbound, Always Allow, RDP service, Any source & destination IP, DNAT IP is 192.168.50.23.
View 7 Replies
View Related
Oct 9, 2012
I cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
View 1 Replies
View Related
Dec 20, 2012
I have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward. Everyone else is dropped. Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.
View 1 Replies
View Related
Sep 25, 2012
Until now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
View 3 Replies
View Related
Mar 11, 2013
I feel I'm having an issue, and I'm unsure why.We own a Cisco RV042 V03 with firmware 4.0.4.02-tm.
I have successfully demonstrated that I can open and forward ports 8001 & 8081 from the WAN side to a specific IP Address on the LAN side.I performed this by going to Setup --> Forwarding, then setup Port Range Forwarding & Port Triggering.
I also changed Setup --> UPnP, then UPnP Function is set to Yes.
My issue is that we would also like to forward 11101 through 11164 in the same maner. However, when I step through the same method described above, it does not seem to work.So now I am confused how I could open the 8001 & 8081 ports, but not the higher 11101 thru 11164 ports.
View 3 Replies
View Related
Dec 20, 2011
I attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies
View Related
Feb 20, 2012
I have a westell 7500 with fairpoint service hooked up to my DSL line. I have disabled woreless on the westell. I then have a linksys e-1000 connected to the westell 7500. I have one wired computer on that network, my imac/game server, my main PC, my wii and an ipod touch connected connected to the linksys e-1000 wirelessly. I want to forward port 25565 through these routers to my imac. How can I do this? I have tried portforward.com, and a million other things.
View 2 Replies
View Related
Jul 25, 2011
I'm having a problem forwarding port 1723. What i'm trying to do is to use VPN to access my server pc and I don't want to use the VPN software that is in the router. When I telnet the port it goes through but when i try to access it outside of the office I can't get through. I've been using [URL] to check port 1723 and I get this:
Error: I could not see your service on XX.XX.XX.XX on port (1723)
Reason: Connection refused
View 4 Replies
View Related
Jun 12, 2011
How do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 Replies
View Related
Dec 27, 2012
There is no support for Model F9J1005v1. How do I update its firmware and how do I port forward on the same
View 2 Replies
View Related
Nov 2, 2011
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies
View Related
Nov 7, 2011
I have one server 172.16.0.100 and i nat this server to a public ip X.X.X.5 and i open RDP for this public ip.Now when i access Remote desktop on this public ip x.x.x.5 it open perfectly.Now my senario is that i want to open a http url on port 5555,server ADMIN open port 80 for this URL on LOCAL lan(http://172.16.0.100:80)So how can i map port 5555 to port 80 on ASA 5520.so when i hit URL [URL]
View 5 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Nov 18, 2012
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
View 1 Replies
View Related
Sep 18, 2012
I have only recently noticed a HUGE decrease in my Utorrent speeds, so i thought i would have a gander and lo and behold.apparently the port Utorrent uses wasn't open. Now, i have tried about 10 different port numbers, made sure Utorrent is being accepted by Norton 360 Firewall,followed complicated directions to (i think) foward ports, and also follow directions to open a specific port.Nothing has worked so far, Utorrent still comes back with a port closed error.
View 1 Replies
View Related
Mar 3, 2013
my router (RV042G V01 Firmware Version : v4.2.1.02 ) get errors I can't understand.Lost connection, can't get a new IP, DNS does not work, total hangup.After a short time / reset everything works fine up to the next error.In the Log I found the following interest entries:undefined Kernel undefined Kernel failed (1).undefined Kernel Message from server.
View 1 Replies
View Related
Sep 24, 2012
I purchased RV042G and setup one-to-one NAT problem to several servers. ometimes the NAT servers lost the internet connection. My case as below
ISP provide two set Public IP Address , one modem
e.g.
set one) 100.100.1.2-6, gateway 100.100.1.1
set two) 200.200.2.2-6, gateway 200.200.2.1
[code]....
All computers and servers (one-to-one NAT) outbound and inbound all work fine. After several hours, only the servers (one-to-one NAT) alert internet connection broken, but the computers (non NAT) still have internet connection.
What's the problem occurs? Why only one-to-one NAT servers lost the connection? and Why only serveral hours later, the server lost the internet connection.
If I changed the WAN setting to same as subnet of the one-to-one NAT, it doesn't occur any problem.
View 3 Replies
View Related
May 20, 2013
I run my business network on the 192.168.x.x range with a server set as 192.168.2.4 statically. The router is currently connecetd to two DCHP wan connections from my ISP, I'm on a residential consumer plan. It has defaulted to loadblanacing with the second WAN however I want to have the second wan's public IP be used by my server and only the server however I wish for the server to still be on the lan so I can use HYPER-V's brided network connection feature to run VMs on the lan, and I would like their wan connection to be from wan 1... as for the entire lan except the server at 192.168.2.4 Is this possible, I can't seem to get the 1-to-1 NAT to do it?
View 4 Replies
View Related
Nov 8, 2012
I've setup the RV042G with one ISP connection for now.I have my main PC running fine, but I have another PC hard lined to the router that had a connection after I power cycled the modem and router but now it no longer does. disabled the network on that PC, now I can't get it back at all.I have a wireless e2000 in one of the ports that I disabled the DCHP on and it seems to be running nicely.before I disabled the PC in question, aka port 3, it was showing as connected in the "192...." but now only as enabled.
View 1 Replies
View Related
Sep 27, 2012
Is there anyway to monitor netflow on RV042G. We have a network at a small school that will get bogged down during the day.
View 1 Replies
View Related
Feb 6, 2013
I have an issue with routing public IPs on the RV042G. I have been able to route the IP's in a couple of different ways, but there is always a nagging problem.
I have a PPPoE Business Class account with 5 routable public IP's. I would like to route the IPs and manage the private network using the RV042G.
Here is what I have tried and the problem that arose: 1) I used 1:1 NAT and the servers responded with no issue. This would be a workable config however I use Kerberos for single sign-on for my clients. To use this security protocol and bind the clients to the server, I must use a public IP on the server machines. In this scenario however, everything else worked fine. 2) I then tried using the DMZ and putting the servers on the DMZ port with a public IP entered in the network config of the machine. That even worked fine and I was excited until I noticed that the servers were reporting the public IP assigned to the DMZ port as their IP when they sent mail. I then ran a test and that is the case. The servers - each with a public IP - are reporting the IP of the DMZ port. I can't have that because the mail servers need to announce a correct IP so the reverse lookup will match. Once again, a little gnat gets in the soup.
View 2 Replies
View Related
Apr 22, 2013
Have a rv042g, newest firmware, trying to setup one to one nat on the configs page, I select enable, enter private ip , enter public ip, enter the range, and click "add to list" and nothing.... no error message, doesn't add to the list below it
View 1 Replies
View Related
Jan 29, 2013
I have RV042G dual WAN VPN router as a gateway in my small office. My ISP requires from me to connect through PPTP VPN to have access to the network. I've configured my router with static IP and every time I connect a laptop or desktop pc I need to connect to the VPN with the Windows VPN client.
View 3 Replies
View Related
Oct 4, 2012
We have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
This issue happens when using any sort of VPN that's supported by the router.
View 1 Replies
View Related
Oct 17, 2012
I have created a protocol binding rule and even a bandwidth rule to make sure outgoing FTP needs to go through WAN2 interface. But it still goes through WAN1, it only works when I disconnect WAN1
View 13 Replies
View Related
