Cisco Routers :: RV042G - Dedicate WAN Port To Specific LAN IP?
Mar 23, 2013
Each of the 2 WAN ports on my RV042G has its own dedicated public IP address. I would like to set up the router so that all incoming traffic on WAN1 is always routed to a specific server (=LAN IP), and vice versa, that particular server's outgoing. Internet traffic is always sent through WAN1.
It has to be controlled by IP address as the system in question is not directly connected to the router, there is a switch in between.
View 2 Replies
ADVERTISEMENT
Jan 8, 2013
We are looking to possibly purchase 2 RV042G routers. The main goal is to tie 2 sites together (via the internet) utilizing the site-to-site VPN feature.
Here is where it gets a little tricky. Since this device has 2 WAN ports, is it possible to assign a seperate IP address for each from our ISP? Then, what we would like to do is assign a couple LAN ports to have the traffic flow through WAN1 and the other LAN ports to flow through WAN2. The LAN addressing can be on the same subnet or seperate.
View 6 Replies
View Related
Oct 25, 2011
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
View 2 Replies
View Related
Jul 1, 2012
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1
match ip 10.136.0.0/16 any
exit
policy qos port-a1-ratelimit
class servers-to-be-slowed action rate-limit kbps 1000
exit
interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
View 4 Replies
View Related
Apr 22, 2013
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
View 2 Replies
View Related
Oct 11, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
View 2 Replies
View Related
Aug 26, 2012
Recently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
View 3 Replies
View Related
Feb 18, 2013
I want to know if is possible to publish a port of an internal server to be accesible from internet but only from a specific IP.I know that in Setup menu exists Forwarding but it allows to publish ports to all internet no matter the source IP.
View 1 Replies
View Related
May 21, 2013
I have RV042 router which is connected to the internet by both the wan ports and I want to use it as a load balancer so that both of my internet connections can be utilized evenly. But now I have an issue in this scenario as my remote application gets logout whenever the communicating IP address changes. Is there any way out so that I can specify the wan port used for a particular public IP address/domain name?
View 1 Replies
View Related
Aug 1, 2012
I have an RV042. I understand and have created the services I need. The documentation is just not clear on how to direct traffic for these services to a specific wan port.
Can this even be done with this router? If so, the how? Use rate control or priority? Does checking a wan port mean that it will only go through that port?
View 4 Replies
View Related
Oct 12, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Oct 23, 2011
is it possible to shutdown a specific port on my 3750x and monitor this port at the same time .for example , im dealing with a mac authenticated network using port security , i want to shut down all the ports that are not used at the moment , however , if some one gets connected to the one of the shutdown ports i want to know the mac address of the user or atleast to know that i have someone who is just plugged in to the one of the shutdowned ports .
View 4 Replies
View Related
Dec 10, 2012
As per the image, is it possible to have dedicated nics between two PCs via a crossover for data transfer/remote access, while still having another nic to access a network for internet, and other systems?The reason I ask is that, it would be very convenient to be able to run backups without having my internet running for some reasons I would rather not go into detail about.
View 8 Replies
View Related
Mar 3, 2013
my router (RV042G V01 Firmware Version : v4.2.1.02 ) get errors I can't understand.Lost connection, can't get a new IP, DNS does not work, total hangup.After a short time / reset everything works fine up to the next error.In the Log I found the following interest entries:undefined Kernel undefined Kernel failed (1).undefined Kernel Message from server.
View 1 Replies
View Related
Sep 24, 2012
I purchased RV042G and setup one-to-one NAT problem to several servers. ometimes the NAT servers lost the internet connection. My case as below
ISP provide two set Public IP Address , one modem
e.g.
set one) 100.100.1.2-6, gateway 100.100.1.1
set two) 200.200.2.2-6, gateway 200.200.2.1
[code]....
All computers and servers (one-to-one NAT) outbound and inbound all work fine. After several hours, only the servers (one-to-one NAT) alert internet connection broken, but the computers (non NAT) still have internet connection.
What's the problem occurs? Why only one-to-one NAT servers lost the connection? and Why only serveral hours later, the server lost the internet connection.
If I changed the WAN setting to same as subnet of the one-to-one NAT, it doesn't occur any problem.
View 3 Replies
View Related
May 20, 2013
I run my business network on the 192.168.x.x range with a server set as 192.168.2.4 statically. The router is currently connecetd to two DCHP wan connections from my ISP, I'm on a residential consumer plan. It has defaulted to loadblanacing with the second WAN however I want to have the second wan's public IP be used by my server and only the server however I wish for the server to still be on the lan so I can use HYPER-V's brided network connection feature to run VMs on the lan, and I would like their wan connection to be from wan 1... as for the entire lan except the server at 192.168.2.4 Is this possible, I can't seem to get the 1-to-1 NAT to do it?
View 4 Replies
View Related
Jan 26, 2012
How can I dedicate a single VPN NAT ip to a single client VPN ? I dont want this ip used by another vpn client....
I got a ASA 5510 with a dhcp pool.cisco vpn client 5.0
View 9 Replies
View Related
Nov 8, 2012
I've setup the RV042G with one ISP connection for now.I have my main PC running fine, but I have another PC hard lined to the router that had a connection after I power cycled the modem and router but now it no longer does. disabled the network on that PC, now I can't get it back at all.I have a wireless e2000 in one of the ports that I disabled the DCHP on and it seems to be running nicely.before I disabled the PC in question, aka port 3, it was showing as connected in the "192...." but now only as enabled.
View 1 Replies
View Related
Sep 27, 2012
Is there anyway to monitor netflow on RV042G. We have a network at a small school that will get bogged down during the day.
View 1 Replies
View Related
Feb 6, 2013
I have an issue with routing public IPs on the RV042G. I have been able to route the IP's in a couple of different ways, but there is always a nagging problem.
I have a PPPoE Business Class account with 5 routable public IP's. I would like to route the IPs and manage the private network using the RV042G.
Here is what I have tried and the problem that arose: 1) I used 1:1 NAT and the servers responded with no issue. This would be a workable config however I use Kerberos for single sign-on for my clients. To use this security protocol and bind the clients to the server, I must use a public IP on the server machines. In this scenario however, everything else worked fine. 2) I then tried using the DMZ and putting the servers on the DMZ port with a public IP entered in the network config of the machine. That even worked fine and I was excited until I noticed that the servers were reporting the public IP assigned to the DMZ port as their IP when they sent mail. I then ran a test and that is the case. The servers - each with a public IP - are reporting the IP of the DMZ port. I can't have that because the mail servers need to announce a correct IP so the reverse lookup will match. Once again, a little gnat gets in the soup.
View 2 Replies
View Related
Apr 22, 2013
Have a rv042g, newest firmware, trying to setup one to one nat on the configs page, I select enable, enter private ip , enter public ip, enter the range, and click "add to list" and nothing.... no error message, doesn't add to the list below it
View 1 Replies
View Related
Jan 29, 2013
I have RV042G dual WAN VPN router as a gateway in my small office. My ISP requires from me to connect through PPTP VPN to have access to the network. I've configured my router with static IP and every time I connect a laptop or desktop pc I need to connect to the VPN with the Windows VPN client.
View 3 Replies
View Related
Oct 4, 2012
We have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
This issue happens when using any sort of VPN that's supported by the router.
View 1 Replies
View Related
Oct 17, 2012
I have created a protocol binding rule and even a bandwidth rule to make sure outgoing FTP needs to go through WAN2 interface. But it still goes through WAN1, it only works when I disconnect WAN1
View 13 Replies
View Related
Mar 16, 2013
I have a problem with the RV042G V01 router manufactured 12/2012.
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !
View 7 Replies
View Related
Jul 8, 2012
I just got the RV042G today. I found the router can only accept 100000 Kbit/sec as bandwith, which is 100Mps only. According to the specification, it should have 1000Mps WAN. I have a internet link of 1000Mps, which is now limited by this router.
View 30 Replies
View Related
Mar 24, 2013
I'm trying to make an attached topology. This router should be attached to 2 different ISPs on both WAN interfaces (ISP1 with IP address - A.B.C.D, and ISP2 with IP W.X.Y.Z) and I want to use DMZ, too. My idea is to make a L2/L3 segmentation with 2 VLANs - Vlan RED for DMZ (private network 192.168.1.0/24) and vlan BLUE for Internal network (network 192.168.2.0/24). I checked in the manual that vlans are supported, but I can't see anything about 802.1q, can I use one trunk port or I should use 2 physical cables?
There should be inter-vlan routing and basic stateful firewall, so PCs in Vlan Blue should be able to initiate connections to DMZ servers, but the opposite should be denied. Router should make a port forwarding on its both WAN interfaces and forward incomming traffic (from Internet) to DMZ servers (with NAT). Both DMZ servers and internal PCs should have an internet access with NAT over both WAN uplinks.
Can I use RV042G for this setup and if not at all - are there any cisco SMB device which can do this?
View 5 Replies
View Related
Nov 11, 2012
How to configure an IPSec VPN with router RV042G.I need to know how to configure an IPSec VPN. Cisco Router with RV042G.
I spend this client your VPN parameters. [code]
View 2 Replies
View Related
Nov 4, 2012
i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
View 4 Replies
View Related
Jun 5, 2013
We are connecting to a Cisco DPC3825 cable modem supplied by our ISP. It has been configured to act as a switch only. They have supplied us with 2 static IP addresses.
When each WAN port is connected individually, everything is fine. I see the IP addresses on the respective WAN port, and it is working fine.
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
How do I get the RV042G working with both WAN ports connected?
View 3 Replies
View Related
Mar 5, 2013
I'm about to upgrading our RV042 to RV042G since everything in the Network ist ready for Gigabit except the RV042
I think it's important to mention that another RV042, which is at a 2nd location, will remain for the VPN connection between the two locations. (Older Hardware are used at the 2nd location).
My Question is, are there any known issues, which should be cleared before changing the router.
Mainly issues with configuration migration and compatibility between RV042 and RV042G VPN connections.
View 3 Replies
View Related
May 11, 2013
I'm trying to set up a single web server in a DMZ using the RV042G and the docs seem woefully inadequate to explain how this is accomplished.
I've attach a picture of my setup..
I'm assigned a single Public IP.. in the example I've used 172.16.5.22 and so I've set the WAN interface for static IP.
The DMZ port is not obvious how to set up.. So I've chosen to define a private subnet and throw the web server in there. As I activate the DMZ, I specify a "subnet" and its address as 10.10.10.1, which I'm assuming goes to the DMZ/WAN port. I assign my webserver the address 10.10.10.3.
I leave the Access rules in their default condition.
I am a little unsure as to how to setup the static IP info for the web server.
Gateway: 10.10.10.1 ?
DNS: 10.10.10.1? or 172.16.5.1?
Problem #1
=========
My first problem is that the webserver cannot access the Internet. I get a timeout when I open the browser. I've tried every address there as the gateway and DNS..
Problem #2
========
If a person on the WAN side is attempting to connect to 172.16.5.22:80, how does the RV042G know to send it to the 10.10.10.3 device? It doesn't know what address the webserver is assigned; I just gave it a 10.10.10.1 address as the subnet address.
I think I'm missing something, conceptually here.
Can, in fact, you use the RV042G in this fashion with only a single public IP address? There is almost no information on how the router actually routes traffic when you choose either 'subnet' or 'range' (where the DMZ is in the same subnet as the WAN)
View 6 Replies
View Related
