How can I dedicate a single VPN NAT ip to a single client VPN ? I dont want this ip used by another vpn client....
I got a ASA 5510 with a dhcp pool.cisco vpn client 5.0
As per the image, is it possible to have dedicated nics between two PCs via a crossover for data transfer/remote access, while still having another nic to access a network for internet, and other systems?The reason I ask is that, it would be very convenient to be able to run backups without having my internet running for some reasons I would rather not go into detail about.
View 8 Replies View RelatedEach of the 2 WAN ports on my RV042G has its own dedicated public IP address. I would like to set up the router so that all incoming traffic on WAN1 is always routed to a specific server (=LAN IP), and vice versa, that particular server's outgoing. Internet traffic is always sent through WAN1.
It has to be controlled by IP address as the system in question is not directly connected to the router, there is a switch in between.
I am able to establish a single VPN session on an ASA 5510. The network is as follows:Cisco 2600 router----> ASA 5510---->non cisco UTM----> LAN.Once another session is connected (same profile different username) is connected the first one disconnected.
View 2 Replies View RelatedWe have an ASA5510 running version 8.25. This is in our central office in London. The London network has an ip address range of 10.110.128.0/22. Connected to this via a site-to-site VPN we have a satellite office that has an IP address range of 172.16.148.0/22.
We have now connected to our parent company via another site-to-site VPN connected to the same ASA5510. Their network has an internal range of 10.110.18.0/24. It was our parent company that issued us with our range of addresses a long while ago so that it all fits in with the rest of the company.
We have resources (web servers) on their network that we use which work just as it all should. We now want to allow our satellite office to view those same web servers. The problem is that only 10.110 addresses can flow to our parent company.
I have configured the firewall at our central office and our satellite office to route across to our parent company via our network network and the packets are flowing just fine except that obviously once they reach our firewall they cannot go to our parent company because the 172.16.148 range cannot be routed there.
My idea is to NAT traffic from our satellite office to one of our local addresses before it goes over to our parent company network.
For example: If someone in our satellite office with an IP address of 172.16.150.5 attempts to request a resource from 10.110.18.12 then the request would go via the VPN to our firewall and then get NATed to 10.110.131.200 before being passed on to our parent company network.
My question is what would the NAT configuration be to achieve this. I just cannot work out what type of NAT I would need or how to construct the command. It's probably PAT as it will be multiple addresses to a single address. Essentialy, all traffic from 172.16.148.0/22 destined for 10.110.18.0/24 should get NATed at our firewall to 10.110.131.200 before being passed on.
Just to add, we already have this working from our Cisco 3000 Concentrator which is now going to be phased out hence trying to get this to work on our ASA. The satellite office has now been moved to the ASA and as of today our parent company has been moved to the ASA.
I have a private network behind a configured Cisco ASA 5510. I need to send data back and forth between a server on the inside network and a device on the outside network on port 44818. No amount of configuration is allowing this to happen. The packet tracer always fails on of the implicity "deny" rules, even though my other rule should explicitly permit it. I also realize I need to set up routing from my outside network to the inside network, but I cannot see from the documentation how to do that on this particular port without simultaneously breaking my outside connection.
The inside IP for the ASA is 192.168.25.1
The outside IP for the ASA 192.168.11.54
Here is my current configuration:
: Saved
: Written by enable_15 at 08:49:25.956 UTC Thu Feb 2 2012
!
ASA Version 8.2(5)
[Code]....
I am working on a project to migrate a single Checkpoint firewall over to a single ASA 5510, no VPN, just firewall. The checkpoint firewall has 8 physical interface so the ASA 5510 also support physical 8 interfaces so thiw will be a one-to-one swap. At the moment, I don't have an ASA 5510 to test my theory so I am going to throw it out here. The checkpoint firewall is a SPLAT running on an powerfull IBM Server with 8 CPU dual cores with 32GB of RAM and it has 1200 rules with over 120,000 objects with some of the crazy NATs but it works so we will just leave it at that. There are not that much traffics going across the firewall so there are no need to put in an ASA 5585
I use the cisco conversion tool to do the policy conversion from Checkpoint to Cisco, I get about 1.5 million lines in the configuration. A lot of it has to do with Checkpoint having no concept of interface security level while ASA does. I am sure I can optimize it to cut down the number of lines in the configuration; however, that is not my main concern at the moment. The customer goal is that at the time when cutover from Checkpoint to Cisco ASA, they want everything to be perfect, meaning that it will work like magic.
My question is that can the ASA 5510 handle 1.5 million lines of configuration? Are there any limitations on this? I know there are limitations with FWSM but since I don't have an 5510 to test.
I would like to know if there is a way to apply in the Cisco asa 5510 traffic shaping not for a interface but a single IP address.For example i would like to limit the bandwith for the IP address of my FTP server.
View 4 Replies View RelatedI am working on an ASA 5510 on 8.4 IOS and need to know how to limit icmp to just a single host? What I would like to do is be able to PING from the Inside interface 10.X.X.X to host 4.2.2.2 on the Outside, but thats it no other host would be PINGable.I tried MANY different access-list statements but the only way I can get icmp out and working is using the "fixup protocol icmp" but then everything is PINGable and the ASA does not block anything.
View 3 Replies View RelatedI have an ASA 5510, one public IP address on my outside interface, an internal email server and a private network.I would like...
1: Users on my private network to be able to access the internet (PAT them to external outside address)
2: Email to be delivered to my MX (my single public IP address translated back to my internal email server.
i.e. can I share my single public IP address to serve translation in both directions (private users surfing the Internet (in-to-out) and an outside to inside NAT for email) ?
Email (MX) = 1.2.3.4
Public (outside) address = 1.2.3.4
Email server internal = 10.1.2.3
Internal private subnet for users = 10.0.0.0/8
I'm new to an ASA 5510 running 8.4(3) and am trying to figure out something regarding time ranges in ASDM. I simply want to allow a single port during business hours only (I'm not concerned about open sessions needing to be closed). So as an example I add a rule something like:
(RULE1 on the internal interface) SRC=INTERNAL DEST=ANY SERVICE=RDP ACTION=PERMIT with a time range set for weekdays 8:00-16:59. I did a test after 5pm on a weekday and was still allowed to do RDP to a server (from INTERNAL), and after using the packet trace tool saw it was still passing through due to a rule a couple lines down (rule 4) that allowed a port range that happened to include port 3389. So my question is if I specify an "allowed" time range and someone attempts access outside that time range, why doesn't it drop it right there? I guess I'm assuming that anything outside the "allowed" time range would be dropped but that doesn't seem to be the case. I'm also assuming the rule base is processed top to bottom.
i have a 5510 with a working VPN but discovered that anyone connecting from a public IP can connect to VPN but can't go anywhere.so if i have say a linksys wifi on my cable modem and a private IP i can connect no problem. but if i'm on like a verizon data card which gives me a public IP i can connect to VPN but receive the below errors in my asa logs and can not reach anything on the network.What do i need added to allow remote ends without a nat device to also work?
View 4 Replies View RelatedSince last week we are having problems with remote users working with VPN client on Windows XP.The connection is stablished but no data traffic occurs.
As we didn't do any change in vpn remote settings I did a test from Linux machine running VPNC client and it works well.It sounds so weird because it happens only on Windows client platform.We have CISCO ASA 5510 and PIX 515 running 8.0(4).
I have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
Secondly request also they need failover over the ISP link.
how we immplement the same on ASA 5510.
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
VLAN 1 - hosts 1.1.1.5 and 1.1.1.6VLAN 2 - hosts 1.1.1.7
Firewall DMZ Interface - 1.1.1.1VLAN 3 - hosts 1.1.1.8 and 1.1.1.9
This way, the hosts are isolated and can't talk to each other unless they're on the same VLAN.I'm working with an ASA 5510 running 8.2.4(4).
I have configured VPN client on my ASA 5510,
I am trying now to telnet my call manager on port 5060 and on port 2000.
When i am connected localy i am able to telnet both ports, but when i am trying to connect through cisco VPN client i am able to telnet the port 2000 and not able to telnet 5060. Both ports are on the same call manager.
When using windows VPN i am able to telnet both ports.
if i removed inspect SIP from: policy-map global_policy class inspection_default
I have a VPN client running on a laptop connected a DSL circuit. The VPN client is configured correctly for an external address on another firewall, this external firewall passes through ISAKMP / IPSEC to an ASA where it terminates. The client authenticates and gets an address from the client pool (VPNCLIENTS – 10.2.16.x / 24) and the tunnel completes with no problems. From the internal ASA I can ping any internal network behind the 10.0.3.240 interface (INSIDE) and I have a route on the inside network to get to the 10.2.16/0 clients to point to this address (10.0.3.240). All good so far.
Now the problems begin. I cant ping anything from the VPN clients (10.2.16.0) network to anywhere, I cant ping any interface on the ASA or any internal network. I also cant ping the client from the ASA and therefore not from the internal network either. This configuration is bare bones configuration so I don’t even have the NAT exception rules added. Network diagram attached too.
interface Ethernet0/0
nameif outside
security-level 0
[Code]......
I am having an ASA 5510 and have configured Clientless SSL VPN in it. Now I need to allow my SSL VPN user to access on a particular application(like mspaint.exe for example).When the user login to the SSL VPN, he should see only the particular aplication or must be able to access on the particular application.
View 2 Replies View RelatedI woudl like to ask all of you that i have ASA 5510 and i want to do VPN client authetication with LDAP, after verify username and password with AD and it use policy with ACS?
View 3 Replies View RelatedI've found that my clients can NOT access to my ASA 5510 with their Cisco VPN Client Ver 5.0 through IPsec over UDP.By comparing my new running config with the old one I found some strang following configuration: [code]
We have 3 diffrent IT expert who have access to our router and I think this configuration is cause of our VPN access problem.Is it really because of that or something else.Any way I want to know how can I get rid of these configuration?
I have a Cisco 2821 and ASA 5510 as a VPN Router in my network.Our remote users are using Cisco VPN Client 5.0.07 and I need to monitor them on a server and keep their Connection Info to generate some reports for my manager.
View 1 Replies View RelatedI have an ASA 5510 with the configuration below. I have configure the ASA as remote access vpn server with cisco vpn client, my problem now is I can connect but I can't ping.
Config
ciscoasa# sh run
: Saved
[Code].....
I've got random connection issue when I try to connect to a VPN gateway through an ASA 5510 (IPSEC client ->ASA 5510->VPN Gateway).
When the tunnel is coming up, those two lines appears in the captured traffic on the internal interface :
<private internal IP>.500 > <destination IP>.500: udp 541
<public external IP>.500 > <destination IP>.500: udp 541
When it's not coming up, the port nuimber for the public IP is not 500
(private internal IP).500 > (destination IP).500: udp 541
(public external IP).442 > (destination IP).500: udp 541
I don't understand why sometimes the port for the public external IP is 500 and sometimes not.
I have some remote locations that connect to my ASA 5510 cluster (Aktive/Passive) using the Cisco VPN Client, from which the connection gets disconnected at random intervals (could be 5 minutes, but sometimes after 15 minutes). However, some other remote locations do not have this problem. All locations have the same VPN client configuration (distrubited by pcf file).
I already disabled isakmp keepalive on the ASA but this did not work. If I read it correctly, the Cisco vpn client logging shows that the ASA initiates the ending of the connection.
Code...
I have a ASA 5510 that uses Radius for Authentication. What I am trying to do is assign each user that logs into VPN to have a specfic static IP based on userid. I have about 30 to 50 users. I don't want to complicate this by having them select a different profile when logging into the ASA. What is a clean and simply way to assign user static ip and not use local database for login?
View 1 Replies View RelatedWe just set up the AnyConnect SSL vpn on our ASA. I am able to establish a connection fine using the Cisco AnyConnect client. I would like to use the native Windows VPN client though if possible. What configuration changes on either the firewall or the client I would need to make for this to happen?
View 1 Replies View RelatedI have an issue witch Cisco VPN-Client V 5.0.06.0160 Remote VPV-Access to ASA 5510 8.2(3)
Evrything works fien but sometimes after about 4-5 Hours the Connection is dropped by the ASA. The Client still prtends to be connected, but there is no connection seen on teh ASA.
I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
View 7 Replies View RelatedNeed configuring Client to Site IP Sec VPN with Hairpin on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IP Sec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make traditional Hairpin model work in this scenario.
Following is the Running-Cong with Normal Client to Site IP Sec VPN configured with No internal Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel:
ASA Version 8.2(1)
!
hostname ciscoasa
[ code ].......
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
What needs to be done here, to hairpin all the traffic to internet coming from VPN Clients. That is I need clients connected via VPN tunnel, when connected to internet, should have their IP's Nattered against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16).
I have ASA 5510 8.4 Firewall where more than 20 Site to Site VPN Clients are configured on it. how to see the traffic for one Specific Site to Site VPN.Actually this site to site vpn is always keep dropping for every minute. I'm sure its a problem at the other end.The remaining 19 VPNS are UP and working without any problem. How to see the traffic for specific vlan.More over we dont have any syslog server in our network. Is their any chance we can check the traffic on the firewall?
View 6 Replies View RelatedI'm on a Mac connecting to a Cisco ASA 5510 with AnyConnect VPN client.
The connection is established and it works for 15-30 seconds, then the connection drops. AnyConnect will reconnect, and then it works fine.
I noticed in the logs that it reconnects with a smaller packet size.
I have an ASa 5510 and setup remote dial in users.
I wanted to use the windows 7 built in client and also the draytek site to site VPN options however when they connect VPN traffic will not work however when i use the cisco VPN client then everything works fine.
All the VPN's connect pretty quickly.In the syslog I a getting errors when i try and ping something: [code]
I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
View 1 Replies View Related