I have an ASa 5510 and setup remote dial in users.
I wanted to use the windows 7 built in client and also the draytek site to site VPN options however when they connect VPN traffic will not work however when i use the cisco VPN client then everything works fine.
All the VPN's connect pretty quickly.In the syslog I a getting errors when i try and ping something: [code]
i have a strange issue with an HSRP Setup. I have two (S1+S2) 3560 as Core/Distribution Layer. Inter-vlan routing are enabled on both Switches. S1 and S2 are connected with an ether channel over four fibre ports. S3 -S5 are the (L2) access layer.
Gi0/1 on S1 and S2 are L3 ports, connect to a Linux Firewall.
HSRP is enabled, S1 is the active router and the STP root bridge.
But, my monitoring via cacti show me, that the Gi0/1 on S2 is active, too! But it should not be active? Only if S1 fails, should S2 the active switch.A client from the access ports on S3 - 5 gets traffic from the Internet via Gi0/1 from S2. Gi0/1 on S1 is active too, but will send mostly traffic to the Internet. Why is S2 active and why route it traffic from the Internet to the client?
I am having touble with a NAT concept. What I have is a 3rd party software VPN product that basically tunnels encapsulated traffic to/from a server sitting inside the network. Right now this traffic utiluizes a physical interface on the ASA5510, but I need the interface for another project.
What I have is this:
Internet<----->ASA<-->router<-->4507(layer3)
| |
| |-Vlan1
[Code]......
I have ASA 5510 8.4 Firewall where more than 20 Site to Site VPN Clients are configured on it. how to see the traffic for one Specific Site to Site VPN.Actually this site to site vpn is always keep dropping for every minute. I'm sure its a problem at the other end.The remaining 19 VPNS are UP and working without any problem. How to see the traffic for specific vlan.More over we dont have any syslog server in our network. Is their any chance we can check the traffic on the firewall?
View 6 Replies View RelatedHaving an issue with the ipsec client being unable to add routes in Windows 7 while connecting to an asa 5510 running 8.3(2). Client connects, but the split-tunnel routes do not get installed on the OS. Vpn client versions used are 5.0.07.0290 and 5.0.07.0440 x64. The client status window shows that it received the split tunnel networks, but the log shows that the routes do not get installed with the following message:
Sev=Warning/2 CVPND/0xE3400013
AddRoute failed to add a route with metric of 100: code 87
Destiantion 192.168.100.0
Netmask 255.255.252.0
Gateway 0.30.1.1
Interface 10.30.1.201
[code].....
I'm having a wierd issue with the VPN client installed on Windows. Eventhough it connects and receive and IP address, I'm not able to access any of the servers on the remote network.
Is there any special configuration need it for it to work on Windows 7 proffesional?
The client works perfect with windows XP, we have a ASA 5510 Version 8.2(2) is in routed Mode
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
Configured cisco 881, WAN has static IP address and LAN is nothing fancy. I can ping out to url... or anywhere from the router but cannot from LAN client computers. [code]
View 4 Replies View RelatedI have a 2821 router with two T1 WICs and have the need to route FTP down one T1 and all other TCP traffic down another T1. All traffic is going to the same remote IP address. The remote sites are in different states, and I assume that the remote subnet is being bridged between the states. It's kind of a weird set up, but it's not my design.
Anyway, can I use a route map to split off FTP traffic to host A and send it down one T1 and have the rest of the IP traffic to host A go down the other T1? I also need to be able to have all traffic use one T1 in case the other T1 goes down.
My first thought was to static all IP down T1-1, then route map FTP traffic down T1-2, then have a floating static for all IP traffic down T1-2 with a higher metric. But something would have to track the T1 interfaces and I'm not sure if route maps or static routes can do that. Any thoughts on this?
I have a router that supports wireless network. I have 2 desktop computers that connect through LAN, 3 Laptops that connect using WiFi. Lot of them use utorrent. I want to block it. They use it to download movies. I have warned them of consequences but they simply dont listen. I dont know how to implement QoS in my router. Mine is UTStarCom.
View 1 Replies View RelatedWe are using a CISCO1921-SEC (ISR) with IOS 15.1 and we configured a "crypto isakmp client configuration group". We can connect with the "Cisco System VPN Client Version 5.0.07.0410" via IPSec/UDP.
1. Is it possible to push routing informations to the System running the VPN Client ? A the moment all traffic is routed to the tunnel but we like only one route to the network permitted with "pool ..." in the "crypto isakmp client configuration group NAME" section.
2. We searched for changing from upd connection to tcp connection via special port. Is it possible with IOS 15.1 on the CISCO1921-SEC ? Is there something possible like "iskamp ipsec-over-tcp port 10000" ?
I am having this problem trying to connect to my university network trough the vpn client from a pc running Windows 7 Ultimate 64-bit: the client connects but I have no Internet access. I first believed that the problem was related to the fact that I had ZoneAlarm Free Antivirus+Firewall installed, but I made several steps, including the complete removal of the ZoneAlarm product, and I still have the same problem.
Here's what I see in the log:
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
[code]....
Using the same client (32 bit version) in another pc of my lan which runs Windows XP and that had never ZoneAlarm installed on it, I have no problems.Also, using Shrew Soft Vpn Client 2.1.7 on the problematic pc I can connect to vpn without problems, so I am really stuck trying to understand what's wrong with Cisco Vpn Client.
I currently have a site to site VPN running connecting a branch office and the Main office using a ASA5510 and ASA 5505. currently PC's at the branch can access the network in the main office using interface 0/1, but we have added another ip range using interface 0/2 and I can't seem to route the traffic to both interfaces. I currently have 0/1 as inside 192.168.10.1 which works, and have added 0/2 as Inside2 192.168.20.1. I know I am forgetting something, any commands to route incoming VPN traffic so PC's at the branch office can connect to both IP ranges?
View 14 Replies View RelatedThe router passes the Interface test for the WAN port in CCP but it still we cannot access the internet. Here is my configuration:
Building configuration...
Current configuration : 3663 bytes
!
! Last configuration change at 09:29:52 Chicago Mon Feb 20 2012 by fbcpekin
version 15.1
[Code].......
I want to route gre traffic through an ACE20, but it doesn't seem to work. The only thing I configured was an ACL with gre enabled, but the ACE20 seems to drop the gre packtes. The gre traffic is entering via the vlan 561 interface and should be send out via the vlan 472 interface. Source 10.94.32.212, destination 10.94.132.39. The tunnel control traffic on port tcp/1723 is working fine. In the service-policies is nothing configured for the gre traffic.
Code...
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies View RelatedI'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies View RelatedI am trying to configure dual ISP on my ASA5505.I have everything configured and working when eth0/0 is connected, but when I disconnect it, it doesn't route any traffic.The static route for the primary isp is removed and the static route to the backup isp shows up, but no traffic goes in or out. I should note that I'm doing this as a proof of concept so eth0/0 is connected to a router and eth0/1 is connected to another router. [code]
View 7 Replies View RelatedWe have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
I am using OPEN VPN in order to connect to a Canadian VPN server.I want ALL internet traffic to ONLY use the VPN connection and no traffic shall pass through my local ISP under any circumstance.In the event the VPN disconnects, I DO NOT want any internet traffic automatically sent via my LOCAL ISP connection. Can I simply disable my LAN network adapter in windows AFTER the vpn is connected? (since vpn uses its own TAP adapter?)
View 2 Replies View RelatedI have a media player wired to my dir-655. I have a wrt300 on the same network to use for vpn. I live in Canada, and to use Netflix etc, from the US, I need to use the vpn.Is it possible to have the media player routed through the wrt300, rather than discovering all the IP addresses for Netflix etc and routing each one?
View 3 Replies View Relatedi want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies View RelatedI have a customer which has a main location office and a remote one. Recently we interconnect their facilities using a local ISP service called Virtual Connectivity, which basically is a private network which can be accessed over aDSL or any other data circuit. They are using Cisco 888 routers to interconnect both sites.At the main site the customer also has an Internet circuit (with a Cisco 857 router)and he wants to remove the Internet circtuit from the remote site and provide them access over their main location Internet circuit.At the primary offices, we installed Cisco 2811 router as a gateway to route the Internet and remote network traffic over the required data circuit. Everything is working fine, but we can not access Internet from the remote location over the circuit installed a the main site. I understand this is a routing issue, since the traffic hits the main office network it does not knows how to reach the Internet. I am assuming this routing must be set into the main office Cisco 888 router (installed by the ISP to interconnect to their private cloud) in order to properly route it over the Internet circuit.Since I already have access over the Internet router and the gateway router at the main site, but not into the ISP router, is there any other way I can make this configurtion over the routers I already have access?
View 3 Replies View RelatedI am working for a company based in Sydney Australia, the company recently open an office in London UK, therefore we are going to get leased lined based on MPLS.We were advised that Customer Edge router will be CISCO1941/K9. We want to our UK client to access our web-based applications via MPLS network instead of internet. The UK office is using BT Business ADSL with 5 Static IP address (please note the modem IP address is actually dynamic), we are going to get a Cisco 857/K9 router which will be used for the entry for the UK client to access the MPLS network. My question will be how do I configure the Cisco 857 router to allow one of the public ip to access the MPLS network. It appears that there are two options, and I am not sure if this is going to work or which one is working better. I have attached two diagrams for clarification of my case.
Option 1 Cisco WAN interface get Dynamic IP (PPPoA) from BT LAN Interface (4 Port) get the assigned 5 Static IP addresses One of the five IPs (217.xx.xx.169) will be assigned to the FE1 (Cisco 1941), any traffic to 217.xx.xx.169 will be routed to the WAN interface of Cisco 1941 to access Sydney service (located in Sydney LAN, mostly http and https traffic) One of the five IPs to 217.xx.xx.170 will be assigned to the WAN interface of Sonicwall Firewall Router which also serve as Internet Access Gateway for LAN users, All trafiic destined for Sydney LAN will be using FE0 (Cisco 1941) as gateway
Option 2Cisco WAN interface get Dynamic IP (PPPoA) from BT LAN Interface (4 Port) will get 192.168.0.1, Cisco 857 router will be the default gateway for LAN users, using one to many NAT, also one to one NAT, One of the five IPs (217.xx.xx.169) will be forwarded to the FE0 (Cisco 1941), any traffic to 217.xx.xx.169 will be routed to the WAN interface of Cisco 1941 to access Sydney service (located in Sydney LAN, mostly http and https traffic)
All of my remote sites use various routers to route all of their traffic via IPsec. However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel. My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway. When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.
View 3 Replies View RelatedJust picked up a ISA550 and have been playing around with it a bit but seem to be having some trouble. I have two LAN subnets in my small business with approx 10 hosts per subnet. I'd like to use the ISA550 to route between them (and to the internet) but can't seem to figure out how. Is it just as simple as creating two VLANS? Can the ISA550 route VLAN traffic?With my old RV042G, I had the option to setup multiple subnets inside the setup menu but I don't see any such area with the 550.
View 2 Replies View RelatedWe have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 Replies View RelatedWe have multiple vpn tunnels coming to our cisco asa 5520 , the problem is that when we create another tunnel with the same network as another network on the firewall , it does not know how to route the traffic to which interface or sub interface.
View 2 Replies View RelatedI have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
Is it possible with the DIR-601 to have one of the IP's on the LAN route all traffic through a proxy server? I would like to have my Roku device (which I've setup as a static on the LAN side) to always connect though a proxy, while all my other devices connect to the internet normally.
View 3 Replies View RelatedI have a new MPLS circuit being stood up for my site; it’s going to replace a site to site VPN connection to our "Headquarters." I want to test this without affecting my production networks. Without getting into alot of details, the admin at the remote site is not very cooperative and basically doesn't want to set this up and I don't have access to his switching/routing. He is prepared to do minimal tasks if necessary. Ultimately, I am looking to test the new Vlan, once successful, route the traffic away from the Site to Site VPN connection to the MPLS circuit. Here is what I plan on doing, I need to determine if it is going to work.
LAN in my office uses EIGRP for routing. MPLS (10.1.1.253) uses OSPF (area 0) and BGP. Currently, traffic destined to headquarters (10.10.1.1/24) uses the default route on a CAT3750 pointing to the firewall (ASA5520) (10.1.1.254).Create new VLAN/DHCP scope to use as a test Vlan to test the new MPLS circuit. 10.1.199.0/24Create static routes on 3750 destined for headquarters for L2L VPN traffic pointing to firewall so traffic to headquarters remains on the L2L connection. ip route 10.10.1.1 255.255.255.0 10.1.1.254 (once I share routes with OSPF, routes to Headquarters will be advertised over the MPLS)Create OSPF instance on the 3750 advertising only the new subnet so that the MPLS network knows to route this traffic over the MPLS for return traffic from headquarters. (this is where it is grey as I don’t know OSPF at all) The switch has a L3 interface which the MPLS router uses as its gateway, so there is direct communication.router-ospf 0 network 10.1.199.0 0.0.0.255 area 0 4. On 3750 create a PBR for the new subnet so that it is routed over the MPLS, (imagine test PC is 10.1.199.100), the remaining production subnets will use the static routes and ignore the OSPF routes because of the shorter administrative distance.Will the PBR route win over the static route for that one subnet? Is that all I need in the OSPF configuration? I see some configs that have neighbor statements with costs, authentication types etc..
this is my first time configuring a cisco router. For instance, a cisco router 1700 with 2 ethernet WICs and 1 LAN port. We have 2 ISPs one more stable than the other. We use an RDP session to an external host identified by lets say IP address 200.1.1.2 using ISP2 to get to this computer. We use ISP1 for all the internet usage, web pages, youtube etc. We are thinking of using this cisco router 1700 to make the packet filtering and routing of this RDP session to the correct ISP2 since we only have 1 NIC per computer on the LAN side.
The main idea would be:
| YES -----> ----------- then use ISP2
LAN---------> Are the packets RDP ?
| No--------> ----------- then use ISP1
Does this can be achieved using packet filtering using extended ACLs and to be router from the lan interface to route rdp (port 3389) packets to ISP2 WAN interface?