We have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 RepliesI have a Cisco 527w which we are wanting to deploy to our remote sites however i've found a bug. We use ADSL with an IPsec tunnel as primary and 3G APN for failover . When the ADSL goes down the route via the IPSec tunnel remains and i am unable to route the traffic via the APN backup without disabling the VPN tunnel .
View 0 Replies View RelatedI have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies View RelatedI'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies View RelatedWe have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
I have set-up a Linksys BEFVP41 VPN router at home (192.168.1.1 / 255.255.255.0)
View 7 Replies View RelatedI have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
I've a asa 5510 on the main site and different ASA 5505 on secundary sites for VPN tunneling between the sites. The problem is that the tunnels are acomplished but no traffic is going over them. What am i doing wrong? For the moment there is a ASA 5505 on the main site managing the tunnels but I want the 5510 to take over the job.
View 5 Replies View RelatedTwo 5505 ASA's for a customer main site and a local office. I have the tunnel up. But I'm unable to pass traffic across it.
Main Site:
ASA Version 7.2(4)
!
hostname Town
enable password iNbSyJZ1ffmb9kn1 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
I have a Site to Site IPSEC VPN Tunnel created with ASDM wizard.
Cisco ASA-5505
Peer A: x.x.x.x
Lan A: 192.168.0.0 255.255.255.0
Fortinet FortiGate-50b
Peer B: y.y.y.y
Lan B: 192.168.23.0 255.255.255.0
I start traffic from LAN B with a ping (or telnet it doesn't matter) that receive no reply but tunnel goes up fine.
"show isakmp sa" seems ok (says "State : MM_ACTIVE")
"show ipsec sa" seems ok but all #pkts are zero
try ftp, telnet from LAN B to LAN A systems but no one work. "show ipsec sa" all #pkts are zero As soon as I generate traffic from LAN A to LAN B these works (with tunnel already up) also traffic from LAN B to LAN A works.Obviously if I end VPN and start tunnel making traffic from LAN A all work fine bidirectionally, LAN A reach LAN B and LAN B reach LAN A.No msg logged in either two appliance.
Seems a very strange problem because seems not related to Phase1 or Phase2 already established.Traffic (routing ?) start works only after at least one packet goes from LAN A to LAN B.No msg logged in either two appliance.Problems begun in ASA version 8.0(4) ASDM version 6.1(3) and remain/continue after upgrade to ASA Version 8.4(1) ASDM version 6.4(1).
I currently have two Cisco ASA 5505. They are at different physical sites (SITE A, SITE B) and are configured with a site-to-site VPN which is active and working.
I can communicate with the subnets on either site from the other and both are connected to the internet, however I need to ensure that all the traffic at my site B goes through this VPN to my site A.
I changed this access-list : access-list outside_2_cryptomap extended permit ip network_siteB network_siteA to access-list outside_2_cryptomap extended permit ip network_siteB any
But this does not work. If I do [URL], site B IP address is not same that site A.
I am trying to set up a LAN-to-LAN VPN tunnel between two sites. One site has a 5505, and the other site has a 5510. It looks like the tunnel is being established fine (both ISAKMP and IPSEC SAs look OK), but traffic doesn't appear to be routing across the internet between the devices. [code]
View 15 Replies View RelatedI have an issue where I can get traffic to pass from HDQ to two branch offices over our ipsec/gre tunnels even though the tunnels appear to be UP. The HDQ is a 2811, branch is a home office using an 871W and branch runs a 2801 router. I initially had HDQ working fine with the 871W but when I configured branch2 (2801), they both broke. The tunnels appear to be up but traffic is not routing across them. The two 2801 routers run 12.4 (c2800nm-adventerprisek9-mz.124-24.T2.bin). These are gre over ipsec tunnels. Currently traffic flows over an exsting MPLS network that we are getting away from due to cost. As soon as I change the routes to point to the Tunnels, it breaks. Traffic doesn't appear to pass through the tunnel. I have attached my sanitized configs.
HDQ#sh crypto sessCrypto session current status
Interface: FastEthernet0/1Session status: UP-ACTIVEPeer: 205.205.205.21 port 500 IKE SA: local 204.204.204.66/500 remote 205.205.205.21/500 Active IPSEC FLOW: permit 47 0.0.0.0/0.0.0.0 0.0.0.0/0.0.0.0 Active SAs: 4, origin: crypto map IPSEC FLOW:
[Code]....
I'm trying to get IPSec VPN working onto a new Cisco ASA5505. Pretty standard configuration.Setup:
* Cisco VPN client on Windows 7 (v5.0.07.0290 x64 on Laptop1 and v5.0.07.0440 x64 on Laptop2)
* PPPoE/NAT and internal DHCP on the ASA were configured with the Startup Wizard in ASDM
NATting is working fine - internal PCs get an IP address in the 192.168.2.0/24 range and can all access the Internet.I wanted to be able to connect from anywhere to the ASA in order to reach one of the internal servers. Should be pretty basic.First I tried with the built-in ASDM IPSec Wizard, instructions found here.VPN clients can connect to the ASA, are connected (until they're manually disconnected), but cannot reach the internal network nor the Internet. Note VPN client can connect fine to a different VPN site (not administered by myself). [code]
Unfortunately I'm getting the same "AddRoute failed to add a route with metric of 0: code 160" error message.I'm very confused as this should be a pretty standard setup. I tried to follow the instructions on the Cisco site to the letter...The only "differences" in my setup are an internal network of 192.168.2.0 (with ASA IP address 192.168.2.254) and PPPoE with DHCP instead of no PPPoE at all.
we have two routers CISCO881-K9 and we have established l2tpv3 pesuduwire between two routers: attached the configuration file for both routers.
Although the l2tp established but we are unable to pass the DHCP or other traffic through l2tp tunnel from router A to router- B. [code]
I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
The networks concerned: name 10.0.0.0 Eventual (HQ Site behind Firewall)name 1.1.1.0 CFS (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0 T1 (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0 Local (Remote Network - internal interface of 5505: 10.20 9. 0.3) On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]
i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies View RelatedEnvironment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies View RelatedI have a Cisco 819 router and it's the first time I've configured any Cisco product. Starting from scratch, I have managed to get 3G working and the VPN to connect but so far no packets can route down the VPN tunnel (the other side is openswan/shorewall on CentOS5).I've been pawing over lots of guides and forum discussions but seem to be a bit lost. I suspect I'm missing some access-list definitions but don't really know how to go about it. I want the network behind the Cisco 819 (10.x.x.0/20) to be able to access the internet through the interface Cellular 0 but also the VPN remote network (192.y.y.0/24)When I ping from the other (non-cisco) end I see on the Cisco 819.
View 9 Replies View RelatedCisco device is neighbored up with a Brocade device via OSPF, and the desired routes are present.This Brocade device is neighbored up with another Brocade device via OSPF over a GRE tunnel. I am not seeing the desired routes present.What kinds of things can I look at to determine the issue? I think I've viewed the OSPF topology database (I'm not that familiar with Brocade) with the show ip ospf routes command and I'm not seeing the desired routes there either.There is no form of route filtering in place. I'll double check, but I do not believe there is any stub routing going on either.
View 12 Replies View RelatedGot a problem routing trafic to my L2L tunnel...
Got an ASA5505 Sec+ with ip 10.45.10.1 on inside interface. Firmware 8.3(1). Got another Cisco router (From my ISP) with ip 10.45.10.254 - This one creates an L2L tunnel - To the 10.45.20.0/24 net.
On the 5505 ive got "route inside 10.45.20.0 255.255.255.0 10.45.10.254 1", and trafic is being directed to 10.45.10.254 as it should.
I know cause I can ping everything one the 10.45.20.0/24 net - But thats it... Cant RDP, connect to fileshare... Nothing.
When i test a PC and set it to gateway 10.45.10.254 I can access everything on the remote network. Do I need some NAT command or an access-list? I've setup AnyConnect VPN on the ASA and I can connect to both networks without any problems.
i measured with Iperf over two Cisco 1811 router, that bandwidth speed is higher then is used IPsec+GRE tunnel between two routers, than just using a static routes.Bandwidth over GRE in average is about 91389Kbit/sec Over static routes is about 88474Kbit/sec.
View 1 Replies View RelatedConfigured cisco 881, WAN has static IP address and LAN is nothing fancy. I can ping out to url... or anywhere from the router but cannot from LAN client computers. [code]
View 4 Replies View RelatedI have a 2821 router with two T1 WICs and have the need to route FTP down one T1 and all other TCP traffic down another T1. All traffic is going to the same remote IP address. The remote sites are in different states, and I assume that the remote subnet is being bridged between the states. It's kind of a weird set up, but it's not my design.
Anyway, can I use a route map to split off FTP traffic to host A and send it down one T1 and have the rest of the IP traffic to host A go down the other T1? I also need to be able to have all traffic use one T1 in case the other T1 goes down.
My first thought was to static all IP down T1-1, then route map FTP traffic down T1-2, then have a floating static for all IP traffic down T1-2 with a higher metric. But something would have to track the T1 interfaces and I'm not sure if route maps or static routes can do that. Any thoughts on this?
I have a router that supports wireless network. I have 2 desktop computers that connect through LAN, 3 Laptops that connect using WiFi. Lot of them use utorrent. I want to block it. They use it to download movies. I have warned them of consequences but they simply dont listen. I dont know how to implement QoS in my router. Mine is UTStarCom.
View 1 Replies View RelatedI currently have a site to site VPN running connecting a branch office and the Main office using a ASA5510 and ASA 5505. currently PC's at the branch can access the network in the main office using interface 0/1, but we have added another ip range using interface 0/2 and I can't seem to route the traffic to both interfaces. I currently have 0/1 as inside 192.168.10.1 which works, and have added 0/2 as Inside2 192.168.20.1. I know I am forgetting something, any commands to route incoming VPN traffic so PC's at the branch office can connect to both IP ranges?
View 14 Replies View RelatedThe router passes the Interface test for the WAN port in CCP but it still we cannot access the internet. Here is my configuration:
Building configuration...
Current configuration : 3663 bytes
!
! Last configuration change at 09:29:52 Chicago Mon Feb 20 2012 by fbcpekin
version 15.1
[Code].......
I want to route gre traffic through an ACE20, but it doesn't seem to work. The only thing I configured was an ACL with gre enabled, but the ACE20 seems to drop the gre packtes. The gre traffic is entering via the vlan 561 interface and should be send out via the vlan 472 interface. Source 10.94.32.212, destination 10.94.132.39. The tunnel control traffic on port tcp/1723 is working fine. In the service-policies is nothing configured for the gre traffic.
Code...
I am trying to configure dual ISP on my ASA5505.I have everything configured and working when eth0/0 is connected, but when I disconnect it, it doesn't route any traffic.The static route for the primary isp is removed and the static route to the backup isp shows up, but no traffic goes in or out. I should note that I'm doing this as a proof of concept so eth0/0 is connected to a router and eth0/1 is connected to another router. [code]
View 7 Replies View RelatedI am using OPEN VPN in order to connect to a Canadian VPN server.I want ALL internet traffic to ONLY use the VPN connection and no traffic shall pass through my local ISP under any circumstance.In the event the VPN disconnects, I DO NOT want any internet traffic automatically sent via my LOCAL ISP connection. Can I simply disable my LAN network adapter in windows AFTER the vpn is connected? (since vpn uses its own TAP adapter?)
View 2 Replies View RelatedI have a media player wired to my dir-655. I have a wrt300 on the same network to use for vpn. I live in Canada, and to use Netflix etc, from the US, I need to use the vpn.Is it possible to have the media player routed through the wrt300, rather than discovering all the IP addresses for Netflix etc and routing each one?
View 3 Replies View Relatedi want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies View Related