i measured with Iperf over two Cisco 1811 router, that bandwidth speed is higher then is used IPsec+GRE tunnel between two routers, than just using a static routes.Bandwidth over GRE in average is about 91389Kbit/sec Over static routes is about 88474Kbit/sec.
View 1 RepliesI have a layer 3 switch with a bunch of SVIs all in the 192.168.x.0/24 range. I just want to advertise a 192.168.0.0/16 summary to the BGP neighbors. I can do this either by:
1) Redistributing connected into BGP and then using the 'aggregate-address' command to advertise the summary.
2) Specifying a network statement in the BGP config for every single SVI, then using the 'aggregate-address' command.
3) Create a static route to null0 (ip route 192.168.0.0 255.255.0.0 null0) and put 'network 192.168.0.0 mask 255.255.0.0' command in the BGP config.All three fulfill the same purpose of summarizing all the SVIs, but creating the static route is much cleaner in this case. It seems like the aggregate-address command is mostly intended for routers that are aggregating connections coming from other routers and all of them share a common prefix.
Got a problem routing trafic to my L2L tunnel...
Got an ASA5505 Sec+ with ip 10.45.10.1 on inside interface. Firmware 8.3(1). Got another Cisco router (From my ISP) with ip 10.45.10.254 - This one creates an L2L tunnel - To the 10.45.20.0/24 net.
On the 5505 ive got "route inside 10.45.20.0 255.255.255.0 10.45.10.254 1", and trafic is being directed to 10.45.10.254 as it should.
I know cause I can ping everything one the 10.45.20.0/24 net - But thats it... Cant RDP, connect to fileshare... Nothing.
When i test a PC and set it to gateway 10.45.10.254 I can access everything on the remote network. Do I need some NAT command or an access-list? I've setup AnyConnect VPN on the ASA and I can connect to both networks without any problems.
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies View RelatedWe have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
configuring some static NAT entries on a remote site 887 router which also has a IPSec tunnel configured back to our main office.
I have been asked to configure some mobile phone "boost" boxes, which will take a mobile phone and send the traffic over the Internet - this is required because of the poor signal at the branch. These boxes connect via Ethernet to the local network and need a direct connection to the Internet and also certain UDP and TCP ports opening up.
There is only one local subnet on site and the ACL for the crypto map dictates that all traffic from this network to our head office go over the tunnel. What I wanted to do was create another vlan, give this a different subnet. Assign these mobile boost boxes DHCP reservations (there is no interface to them so they cannot be configured) and then allow them to break out to the Internet locally rather than send the traffic back to our head office and have to open up ports on our main ASA firewall.
[URL]
So I went ahead and created a separate vlan and DHCP reservation and then also followed the guidelines outlined above about using a route-map to stop the traffic being sent down the tunnel and then configured static NAT statements for each of the four ports these boost boxes need to work. I configure the ip nat inside/outside on the relevant ports (vlan 3 for inside, dialer 1 for outside) The configuration can be seen below for the NAT part;
! Denies vpn interesting traffic but permits all otherip access-list extended NAT-Trafficdeny ip 172.19.191.0 0.0.0.255 172.16.0.0 0.3.255.255deny ip 172.19.191.0 0.0.0.255 10.0.0.0 0.255.255.255deny ip 172.19.191.0 0.0.0.255 192.168.128.0
[Code].....
Is it possible to re-route our Site 2 Site VPN over our Static Route (T1) if the WAN fails?
View 1 Replies View RelatedOn an ASA 5505 with the proper licenses running version 8.3, which would you consider the more resource intensive for the ASA, IPSec VPN or an SSL VPN with a portal?
The connections through the firewall would be the same so I am curious how adding the different types of VPN will affect the CPU and overall ability of the ASA to function.
we are running 8.4(2) on the asa with the below configuration we basically have a static for .7 on .25 and a nat for .7 for port direction with manual nat that takes precedense over auto nat within the object group am I correct that I dontneed the dynamic statement and that its redundant?
-object network obj-10.X.0.25-02host 10.X.0.25
-object network obj-10.X.0.25nat (any,INSIDE) static X.X.X.7 dns
-object network obj-10.X.0.25-01nat (INSIDE,OUTSIDE) static X.X.X.7 service tcp smtp smtp
-object network obj-10.X.0.25-02nat (INSIDE,OUTSIDE) dynamic X.X.X.7
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies View RelatedI am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
Basically I have a bunch of computers that are being routed through a specific gateway in order to access a web page that is hosted internally on a separate subnet. I set up static routes on all of the computers, and they all work... except one.Here's what a route print -4 looks like for a working computer (Windows 7):
Code:
===========================================================================
Interface List
14...xx xx xx xx xx xx ......Broadcom 802.11n Network Adapter
11...xx xx xx xx xx xx ......Realtek PCIe GBE Family Controller
1...........................Software Loopback Interface 1
[code]....
Both of these stations are running Windows 7.So essentially what I am trying to do here is route all traffic to the 10.zzz.zzz.0 subnet through the 10.xxx.xxx.147 gateway. Everything else should go through the 10.xxx.xxx.230 gateway. This is the intended behavior, and again it is working everywhere but that one station.
I have a Cisco 819 router and it's the first time I've configured any Cisco product. Starting from scratch, I have managed to get 3G working and the VPN to connect but so far no packets can route down the VPN tunnel (the other side is openswan/shorewall on CentOS5).I've been pawing over lots of guides and forum discussions but seem to be a bit lost. I suspect I'm missing some access-list definitions but don't really know how to go about it. I want the network behind the Cisco 819 (10.x.x.0/20) to be able to access the internet through the interface Cellular 0 but also the VPN remote network (192.y.y.0/24)When I ping from the other (non-cisco) end I see on the Cisco 819.
View 9 Replies View RelatedAdd static route for new exchange server?
View 1 Replies View RelatedVPN 1841, and static nat. I have to create VPN to connect to remote network, but problem is that they already use same subnet as mine. How to configure static nat on cisco 1841 so static nat will work and address will be translated in different IP when connection trough VPN.I have address 192.168.235.1 and I want to translate to 192.168.100.1,This 1841 is border router, and all VLNAs and VLANs routing is on 3650.
View 12 Replies View RelatedI config the routers with EIGRP and also write Static route between two PC before remove the link between router0 and router1 , destination is reachable , but when remove this connection , packet from pc1 to pc0 will drop in a loop and never reach to destination , is it possible to have a Link state routing protocol and static route at the same network like this scenario , how to prevent loop in this topology static route is configure as bellow :
router0 <==> router 1 <==> router2 <==> router3 <==> router <==>pc1
I have a new Cisco 819 router wtih Verizon 3G built in. I want to use this router to provide 3G backup Internet access for a customer kiosk. The 3G is perfectly stable when I use it as a primary, static routed connection. When I use a floating static route, the link goes up and down constantly. The 3G link works for a about 20- 30 seconds, then goes to reset, down, then dials up and reconnects.
View 2 Replies View RelatedI have a nat and vpn setup on my Cisco 2801 router.Everything is working as expected except the NAT. I have a single static nat translation but it only works for inbound and not outbound. Going outbound, it uses the default overload nat address of the outside interface. [code] I want to add another mailserver. But I fear if one mailserver were to get black-listed, they would both be reporting there ip address as the same address (the one on the ethernet interface) which would blacklist both mail servers.Again, inbound nat works ok, but outbound is just using the IP of the ethernet0/0 address.
View 2 Replies View RelatedIn my Lab environment in GNS I have connected two 7200 series router through fastethernet on router A I have given IP adress 192.168.10.54 and router B I have given IP address 192.168.10.53 and default route as 0.0.0.0 0.0.0.0 192.168.10.53 and when I run the command on router A it shows result as follows "C 192.168.10.52/24 is directly connected ,Fast ethernet 2/0".
So I need to know why it's showing the result of .52 at last why not .53 or .54 at last what is the reason it's showing .52 which I have not mentioned in my IP address.
We have a customer, who has the following setup:
ISP router with ip range: x.x.202.1/ 28
That is connected to a Cisco 2960 switch, that doesn't do much but:
Vlan5: x.x.202.14 /28
Port 1-12 is switchport mode access to vlan 5 There are 3 firewall's connected to the 2960
1: D-Link DSR-1000N with ip x.x.202.2 /28
gw: x.x.202.1
2: Uknown
3: Cisco ASA 5505 with ip: x.x202.7 /28
static route: x.x.202.1
Each FW have a LAN behind it. The D-Link and the unknown device are both working perfectly and clients on each subnet can connect to the internet?However when I connect the ASA 5505 to the 2960 SW with a configued static route: Route Outside 0.0.0.0 0.0.0.0 x.x.202.1 1 is says it has no route to host?
Sanitized Config for the ASA 5505 is:
hostname ciscoasa
domain-name network.local
names
!
interface Ethernet0/0
switchport access vlan 2
[code]....
If I connect the ASA5505 to the LAN of D-Link DSR-1000N and give it a static address and a static route match the D-Link LAN network, it works perfectly, however not when I connect it the the Cisco 2960 Switch
I have a Cisco 1841 with a DSL and 3G HWIC interface. I would like to setup the DSL as the primary link and then use the 3G as a backup interface. I am trying to accomplish this using the Floating Static routes with SLA object tracking.
I have tried various options, like having two tracked routes, one tracked route, changing administrative distances, multiple SLA's, etc etc.
My problem basically is that when the DSL (Dialer0) goes down and the 3G (Cellular0/1/0) takes over, that the SLA never changes back when the DSL is available again, so that the DSL can take over as the primary link again. [code]
Cisco device is neighbored up with a Brocade device via OSPF, and the desired routes are present.This Brocade device is neighbored up with another Brocade device via OSPF over a GRE tunnel. I am not seeing the desired routes present.What kinds of things can I look at to determine the issue? I think I've viewed the OSPF topology database (I'm not that familiar with Brocade) with the show ip ospf routes command and I'm not seeing the desired routes there either.There is no form of route filtering in place. I'll double check, but I do not believe there is any stub routing going on either.
View 12 Replies View RelatedI have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
I'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies View RelatedI am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
View 1 Replies View RelatedI have my internet connection connect to my main Linksys router WRT160NL (192.168.1.1) with 192.168.1.x.My 2nd Linksys router connect to the first one as Gateway as well.The 2nd router has its WAN ip of 192.168.1.100 and it's local subnet as 192.168.2.x.My machines at 192.168.2.x can get to the internet and connect to all machines in the 192.168.1.x network.However, the 1.x network can't access the machines on the 2's network. And because of that, i can not sharing or printing between two network.I try to add static routes on my main router (192.168.1.1) with the route: 192.168.2.0 mask 255.255.255.0 and defaute gateway 192.168.1.100However, the route not work still.anyway to make sure that the 1.x network able to access the 2.x network and from 2.x access 1.x for sharing files and printing.
View 1 Replies View Relatedstatic route on RV042?
View 1 Replies View RelatedI am setting up a remote site to provide a backup internet circuit for outbound traffic. Everything is working from the main site by redistributing a static route and using default-information originate within BGP to my MPLS provider.Now on the remote site I setup a static route with an AD of 250 which is higher than the AD of 20 we are getting from the main site over the MPLS network. When the route come up BGP uses the default route from the main site and everything works fine. When I clear the BGP routes at the main site the backup site installs the static route with a higher AD. The problem is when the BGP route comes back up the static route is not getting removed. From looking at some other posts it seems that the redistributed local route is still preferred by BGP. They mentioned setting the weight to 0 in a route map which I tried but I am not getting the results of removing the static route and using the BGP route.Remote site router config: router bgp 65011. [code]
View 24 Replies View RelatedMy 2811 is connected with two ISP,s as below and have VPN with Central branch.I want to set DSL as primary and WiMax as secondary but problem is that routes learned via BGP get precedence over default route as they are specific one.I think i may need to put all static specific routes of central branch over DSL along defautl but I want any idea if my default route stay active and when it down then BGP neighborship can be establish (like ip sla tracking.)
View 3 Replies View RelatedI have Cisco RV180. I can not set static route with destination to all IPs (0.0.0.0/0.0.0.0). It always shows errors. It asked me to input non zero number. I can do this on Cisco RV042 without any problem.
View 3 Replies View RelatedHave a solution with PFR with two master controller in hsrp mode and two active border controller, betwen the MC and the BR i'm running EIGRP. The two BR have BGP to the ISP but i have default router for the parent route. Same weeks ago i notice some problems in reaching to specific public ip addr. During the trobleshooting i found that the two border controller have dynamic-pbr applyed to the inside interfaces and one of the satement on the dynamic route-map is setting the next-hop for the destination public ip addr yhe inside interface on the two border routers. This way the traffic is looping betewn the two BR. It's possibel do disable the PIRO (PBR) and only to use static route injection betwen the MC and BR.
The routers are running 12.4.24T
We use ASDM 6.2 to manage our Cisco ASA 5520 running ASA Software Version 8.2 (1). I just noticed that some static routes have "A-" when you view the static routes with ASDM e.g. A-172.24.0.0 or A-192.168.176.0 (pls see attached print screen). I haven't seen this before and dont know what it means.
View 4 Replies View RelatedWe have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 Replies View Related