Cisco WAN :: 12.4.24T / Disable The PIRO (PBR) And Only To Use Static Route Injection Between The MC And BR?
Feb 23, 2010
Have a solution with PFR with two master controller in hsrp mode and two active border controller, betwen the MC and the BR i'm running EIGRP. The two BR have BGP to the ISP but i have default router for the parent route. Same weeks ago i notice some problems in reaching to specific public ip addr. During the trobleshooting i found that the two border controller have dynamic-pbr applyed to the inside interfaces and one of the satement on the dynamic route-map is setting the next-hop for the destination public ip addr yhe inside interface on the two border routers. This way the traffic is looping betewn the two BR. It's possibel do disable the PIRO (PBR) and only to use static route injection betwen the MC and BR.
My network consists of a router and a ASA5505. The router has a serial connection back ot HQ. The ASA has a VPN connection back to HQ. I want the network traffic destined for HQ to travel over the VPN connection until that connection is no longer valid (down). I've been told that RRI is the way to go but cannot get it to work. I get one of my routes to show up in the router but that's it (and not as a static route). Also I don't want the routes to be injected if the VPN connection is down. But I do want the VPN connection to be the preferred connection.
We have two ASA5510's connected to two different ISP's and both able to initiate a site-site IPsec connection to a remote site. Depending on the state of the ISP's either ASA may initiate this VPN.We use Reverse Route Injection into OSPF for VPN clients and it works fine with the route being distributed when a client connects and disappearing when there are no clients.So we thought we'd try it for our site-site VPN's. Unfortunately when we enable Reverse Route Injection the routes are distributed regardless of whether the VPN is up or not, so if one ASA has initiated a VPN it's reverse route is distributed (which is what we want) but the other ASA also distributes a route for it's non-existent VPN. The result is that our gateway routers see two OSPF routes and can't ascertain which route is actually up.
Is there any way to distribute the route using Reverse Route Injection (or any other method) only when a site-site VPN is actually up? For various reasons we can't use BGP or other gateway routing protocols.Our ASA5510 are currently running IOS 8.2(1)
VPN 1841, and static nat. I have to create VPN to connect to remote network, but problem is that they already use same subnet as mine. How to configure static nat on cisco 1841 so static nat will work and address will be translated in different IP when connection trough VPN.I have address 192.168.235.1 and I want to translate to 192.168.100.1,This 1841 is border router, and all VLNAs and VLANs routing is on 3650.
Basically I have a bunch of computers that are being routed through a specific gateway in order to access a web page that is hosted internally on a separate subnet. I set up static routes on all of the computers, and they all work... except one.Here's what a route print -4 looks like for a working computer (Windows 7):
Code: =========================================================================== Interface List 14...xx xx xx xx xx xx ......Broadcom 802.11n Network Adapter 11...xx xx xx xx xx xx ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1
[code]....
Both of these stations are running Windows 7.So essentially what I am trying to do here is route all traffic to the 10.zzz.zzz.0 subnet through the 10.xxx.xxx.147 gateway. Everything else should go through the 10.xxx.xxx.230 gateway. This is the intended behavior, and again it is working everywhere but that one station.
I config the routers with EIGRP and also write Static route between two PC before remove the link between router0 and router1 , destination is reachable , but when remove this connection , packet from pc1 to pc0 will drop in a loop and never reach to destination , is it possible to have a Link state routing protocol and static route at the same network like this scenario , how to prevent loop in this topology static route is configure as bellow :
I have a new Cisco 819 router wtih Verizon 3G built in. I want to use this router to provide 3G backup Internet access for a customer kiosk. The 3G is perfectly stable when I use it as a primary, static routed connection. When I use a floating static route, the link goes up and down constantly. The 3G link works for a about 20- 30 seconds, then goes to reset, down, then dials up and reconnects.
I have a nat and vpn setup on my Cisco 2801 router.Everything is working as expected except the NAT. I have a single static nat translation but it only works for inbound and not outbound. Going outbound, it uses the default overload nat address of the outside interface. [code] I want to add another mailserver. But I fear if one mailserver were to get black-listed, they would both be reporting there ip address as the same address (the one on the ethernet interface) which would blacklist both mail servers.Again, inbound nat works ok, but outbound is just using the IP of the ethernet0/0 address.
Got an ASA5505 Sec+ with ip 10.45.10.1 on inside interface. Firmware 8.3(1). Got another Cisco router (From my ISP) with ip 10.45.10.254 - This one creates an L2L tunnel - To the 10.45.20.0/24 net.
On the 5505 ive got "route inside 10.45.20.0 255.255.255.0 10.45.10.254 1", and trafic is being directed to 10.45.10.254 as it should.
I know cause I can ping everything one the 10.45.20.0/24 net - But thats it... Cant RDP, connect to fileshare... Nothing.
When i test a PC and set it to gateway 10.45.10.254 I can access everything on the remote network. Do I need some NAT command or an access-list? I've setup AnyConnect VPN on the ASA and I can connect to both networks without any problems.
In my Lab environment in GNS I have connected two 7200 series router through fastethernet on router A I have given IP adress 192.168.10.54 and router B I have given IP address 192.168.10.53 and default route as 0.0.0.0 0.0.0.0 192.168.10.53 and when I run the command on router A it shows result as follows "C 192.168.10.52/24 is directly connected ,Fast ethernet 2/0".
So I need to know why it's showing the result of .52 at last why not .53 or .54 at last what is the reason it's showing .52 which I have not mentioned in my IP address.
Each FW have a LAN behind it. The D-Link and the unknown device are both working perfectly and clients on each subnet can connect to the internet?However when I connect the ASA 5505 to the 2960 SW with a configued static route: Route Outside 0.0.0.0 0.0.0.0 x.x.202.1 1 is says it has no route to host?
If I connect the ASA5505 to the LAN of D-Link DSR-1000N and give it a static address and a static route match the D-Link LAN network, it works perfectly, however not when I connect it the the Cisco 2960 Switch
I have a Cisco 1841 with a DSL and 3G HWIC interface. I would like to setup the DSL as the primary link and then use the 3G as a backup interface. I am trying to accomplish this using the Floating Static routes with SLA object tracking.
I have tried various options, like having two tracked routes, one tracked route, changing administrative distances, multiple SLA's, etc etc.
My problem basically is that when the DSL (Dialer0) goes down and the 3G (Cellular0/1/0) takes over, that the SLA never changes back when the DSL is available again, so that the DSL can take over as the primary link again. [code]
I am setting up a remote site to provide a backup internet circuit for outbound traffic. Everything is working from the main site by redistributing a static route and using default-information originate within BGP to my MPLS provider.Now on the remote site I setup a static route with an AD of 250 which is higher than the AD of 20 we are getting from the main site over the MPLS network. When the route come up BGP uses the default route from the main site and everything works fine. When I clear the BGP routes at the main site the backup site installs the static route with a higher AD. The problem is when the BGP route comes back up the static route is not getting removed. From looking at some other posts it seems that the redistributed local route is still preferred by BGP. They mentioned setting the weight to 0 in a route map which I tried but I am not getting the results of removing the static route and using the BGP route.Remote site router config: router bgp 65011. [code]
My 2811 is connected with two ISP,s as below and have VPN with Central branch.I want to set DSL as primary and WiMax as secondary but problem is that routes learned via BGP get precedence over default route as they are specific one.I think i may need to put all static specific routes of central branch over DSL along defautl but I want any idea if my default route stay active and when it down then BGP neighborship can be establish (like ip sla tracking.)
I have Cisco RV180. I can not set static route with destination to all IPs (0.0.0.0/0.0.0.0). It always shows errors. It asked me to input non zero number. I can do this on Cisco RV042 without any problem.
We use ASDM 6.2 to manage our Cisco ASA 5520 running ASA Software Version 8.2 (1). I just noticed that some static routes have "A-" when you view the static routes with ASDM e.g. A-172.24.0.0 or A-192.168.176.0 (pls see attached print screen). I haven't seen this before and dont know what it means.
i measured with Iperf over two Cisco 1811 router, that bandwidth speed is higher then is used IPsec+GRE tunnel between two routers, than just using a static routes.Bandwidth over GRE in average is about 91389Kbit/sec Over static routes is about 88474Kbit/sec.
I have a layer 3 switch with a bunch of SVIs all in the 192.168.x.0/24 range. I just want to advertise a 192.168.0.0/16 summary to the BGP neighbors. I can do this either by:
1) Redistributing connected into BGP and then using the 'aggregate-address' command to advertise the summary.
2) Specifying a network statement in the BGP config for every single SVI, then using the 'aggregate-address' command.
3) Create a static route to null0 (ip route 192.168.0.0 255.255.0.0 null0) and put 'network 192.168.0.0 mask 255.255.0.0' command in the BGP config.All three fulfill the same purpose of summarizing all the SVIs, but creating the static route is much cleaner in this case. It seems like the aggregate-address command is mostly intended for routers that are aggregating connections coming from other routers and all of them share a common prefix.
I have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route: Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
I have a new MPLS circuit being stood up for my site; it’s going to replace a site to site VPN connection to our "Headquarters." I want to test this without affecting my production networks. Without getting into alot of details, the admin at the remote site is not very cooperative and basically doesn't want to set this up and I don't have access to his switching/routing. He is prepared to do minimal tasks if necessary. Ultimately, I am looking to test the new Vlan, once successful, route the traffic away from the Site to Site VPN connection to the MPLS circuit. Here is what I plan on doing, I need to determine if it is going to work.
LAN in my office uses EIGRP for routing. MPLS (10.1.1.253) uses OSPF (area 0) and BGP. Currently, traffic destined to headquarters (10.10.1.1/24) uses the default route on a CAT3750 pointing to the firewall (ASA5520) (10.1.1.254).Create new VLAN/DHCP scope to use as a test Vlan to test the new MPLS circuit. 10.1.199.0/24Create static routes on 3750 destined for headquarters for L2L VPN traffic pointing to firewall so traffic to headquarters remains on the L2L connection. ip route 10.10.1.1 255.255.255.0 10.1.1.254 (once I share routes with OSPF, routes to Headquarters will be advertised over the MPLS)Create OSPF instance on the 3750 advertising only the new subnet so that the MPLS network knows to route this traffic over the MPLS for return traffic from headquarters. (this is where it is grey as I don’t know OSPF at all) The switch has a L3 interface which the MPLS router uses as its gateway, so there is direct communication.router-ospf 0 network 10.1.199.0 0.0.0.255 area 0 4. On 3750 create a PBR for the new subnet so that it is routed over the MPLS, (imagine test PC is 10.1.199.100), the remaining production subnets will use the static routes and ignore the OSPF routes because of the shorter administrative distance.Will the PBR route win over the static route for that one subnet? Is that all I need in the OSPF configuration? I see some configs that have neighbor statements with costs, authentication types etc..
I defined a static route: 192.168.0.0 / 255.255.255.0 / 192.168.1.201 (gateway), I can connect from 192.168.1.0 to 192.168.0.0 but we cannot ping in this local network. We have a CISCO 18000 as a VPN IP configured between this two local network.
We have two sites: 192.168.100.x and 192.168.101.x currently connected via IPsec VPN. On each end we have a Cisco ASA 5505. However, each site also has an MPLS VPN with intentions to move all traffic to this link. Will this work on the ASA? We need to make sure traffic can hit the ASA @ site A on the inside interface and trafiic will forward to the MPLS VPN router which then handles the traffic. Too, will it cause any problems in bi-directional flow between the two sites?
I plan to configure Static route load-balancing, which just assign different administraive distance to static routes.The route with lower distance is preferred. For example, if ISP A is our primary Internet provider the default route may be configured with a distance of 1 (all static routes are assigned this administrative distance) and the default route through ISP B may be configured with a distance of 100. In that case the default route through ISP B will be used if only the route through ISP A becomes unavailable.
But when I trying to configureWith Enhanced Object Tracking to do the route failover (a generic track object can monitor presence of an ip route, state of an SLA), I found my IOS not support such Track command. [code]
If we have catos 6509 and MSFC and we need to connect new building with L3 I want to Do static route between two network i need to but ip in interface of switch should I but this ip on catos or MSFC,
Switch(config)# interface fastethernet 2/1 Switch(config-if)# ip address x.x.x.x x.x.x.x
In catos if want want do like above command what is the command .
At the moment if I try and access data from VLAN 1 to VLAN 4 it gets to the destination ok going through the static route and over the vInterOffice connection but the problem is VLAN 4 returning the traffic. This fails because there is no static route back to VLAN 1. If I create a static route from Office 2 to VLAN 1 then it will route all my data traffic over it as well.
Basically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
I am trying to set up my ASA5510 the fail over of ISP when it can't ping three different IP. I create three different tracking to three different IP using sla monitor & track rtr. But when I do
the last route will replace the previous two and only the last route command takes effect.Is there anyway I can set up the fail over to ISP2 only when it can't ping three different IP from ISP1?
I am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
I have my internet connection connect to my main Linksys router WRT160NL (192.168.1.1) with 192.168.1.x.My 2nd Linksys router connect to the first one as Gateway as well.The 2nd router has its WAN ip of 192.168.1.100 and it's local subnet as 192.168.2.x.My machines at 192.168.2.x can get to the internet and connect to all machines in the 192.168.1.x network.However, the 1.x network can't access the machines on the 2's network. And because of that, i can not sharing or printing between two network.I try to add static routes on my main router (192.168.1.1) with the route: 192.168.2.0 mask 255.255.255.0 and defaute gateway 192.168.1.100However, the route not work still.anyway to make sure that the 1.x network able to access the 2.x network and from 2.x access 1.x for sharing files and printing.
I am attempting to access the service port from a client pc on another network.
Service port = 10.100.2.1/16 Client IP = 10.1.1.10/16
I know you cannot put a default gateway on the service port, but the documentation says you can add a static route for remote management. So I tried...