Cisco VPN :: ASA5505 - Static Route To L2L Tunnel
Feb 14, 2011
Got a problem routing trafic to my L2L tunnel...
Got an ASA5505 Sec+ with ip 10.45.10.1 on inside interface. Firmware 8.3(1). Got another Cisco router (From my ISP) with ip 10.45.10.254 - This one creates an L2L tunnel - To the 10.45.20.0/24 net.
On the 5505 ive got "route inside 10.45.20.0 255.255.255.0 10.45.10.254 1", and trafic is being directed to 10.45.10.254 as it should.
I know cause I can ping everything one the 10.45.20.0/24 net - But thats it... Cant RDP, connect to fileshare... Nothing.
When i test a PC and set it to gateway 10.45.10.254 I can access everything on the remote network. Do I need some NAT command or an access-list? I've setup AnyConnect VPN on the ASA and I can connect to both networks without any problems.
View 2 Replies
ADVERTISEMENT
May 9, 2013
We have a HUB ASA5505 SEC+ with a few other ASA's connected to it via L2L VPN. We have 1 active Static L2L, 1 Active Dynamic L2L, and I'm currently trying to add a Second Static L2L Tunnel.I verified that each WAN Interface can ping each other, and both devices have full internet connectivity. There is no double nat or content filtering going on either. I did notice that my Cisco Remote Access VPN Client won't connect properly through the ASA despite full internet connectivity, but when I connect directly to the modem I was able to connect properly. So apparently the ISP isn't blocking IPSEC traffic AFAIK.
Static2 is currently using a Temporary TAC License since our license is currently awaiting arrival, but a show version output shows that all VPN/3des features are enabled. [code]
View 1 Replies
View Related
Aug 14, 2012
i measured with Iperf over two Cisco 1811 router, that bandwidth speed is higher then is used IPsec+GRE tunnel between two routers, than just using a static routes.Bandwidth over GRE in average is about 91389Kbit/sec Over static routes is about 88474Kbit/sec.
View 1 Replies
View Related
Nov 14, 2012
customer's WAN solution, instead of buying routers, purchasing department bought ASA's (don't even get me started!). So I have 5 ASA 5505's for the branch offices and one 5510 for the Head Office. I am trying to get them to behave like routers and pass the traffic across. I set up a lab with a 5505 and the 5510 using an ethernet cable for both Outside interfaces since the WAN links are going to be MetroEthernet Layer 2 anyway.
I tried static routes, dynamic routing, I followed examples from other persons who did it and it doesn't work. I attached the configs here to show I have the default routes, specific static routes pointing the traffic out, any any rules configured as well. I cannot ping from the internal lan of the 5505 to the internal lan of the 5510.
View 1 Replies
View Related
Nov 29, 2011
i have cisco asa 5505 Security adaptive firewall. my inside network is 192.168.1.0 255.255.255.0 . i want to add static route another network i have that network id is 192.168.2.0 . 255.255.255.0.how i can add the route.
View 9 Replies
View Related
May 25, 2011
My network consists of a router and a ASA5505. The router has a serial connection back ot HQ. The ASA has a VPN connection back to HQ. I want the network traffic destined for HQ to travel over the VPN connection until that connection is no longer valid (down). I've been told that RRI is the way to go but cannot get it to work. I get one of my routes to show up in the router but that's it (and not as a static route). Also I don't want the routes to be injected if the VPN connection is down. But I do want the VPN connection to be the preferred connection.
View 2 Replies
View Related
Apr 23, 2012
I am trying to configure dual ISP on my ASA5505.I have everything configured and working when eth0/0 is connected, but when I disconnect it, it doesn't route any traffic.The static route for the primary isp is removed and the static route to the backup isp shows up, but no traffic goes in or out. I should note that I'm doing this as a proof of concept so eth0/0 is connected to a router and eth0/1 is connected to another router. [code]
View 7 Replies
View Related
Jan 20, 2013
I have a Cisco 819 router and it's the first time I've configured any Cisco product. Starting from scratch, I have managed to get 3G working and the VPN to connect but so far no packets can route down the VPN tunnel (the other side is openswan/shorewall on CentOS5).I've been pawing over lots of guides and forum discussions but seem to be a bit lost. I suspect I'm missing some access-list definitions but don't really know how to go about it. I want the network behind the Cisco 819 (10.x.x.0/20) to be able to access the internet through the interface Cellular 0 but also the VPN remote network (192.y.y.0/24)When I ping from the other (non-cisco) end I see on the Cisco 819.
View 9 Replies
View Related
Feb 6, 2013
I would hereby like to inform if it is possible to configure the Cisco ASA5505 firewall to route internet via an external VPN, while a laptop and smartphone connect to the firewall via Cisco AnyConnect VPN.
The configuration would result into: Laptop on public internet -> Cisco ASA5505 VPN -> External VPN (Unix server) -> internet.
View 4 Replies
View Related
Feb 21, 2012
VPN 1841, and static nat. I have to create VPN to connect to remote network, but problem is that they already use same subnet as mine. How to configure static nat on cisco 1841 so static nat will work and address will be translated in different IP when connection trough VPN.I have address 192.168.235.1 and I want to translate to 192.168.100.1,This 1841 is border router, and all VLNAs and VLANs routing is on 3650.
View 12 Replies
View Related
Sep 19, 2012
Basically I have a bunch of computers that are being routed through a specific gateway in order to access a web page that is hosted internally on a separate subnet. I set up static routes on all of the computers, and they all work... except one.Here's what a route print -4 looks like for a working computer (Windows 7):
Code:
===========================================================================
Interface List
14...xx xx xx xx xx xx ......Broadcom 802.11n Network Adapter
11...xx xx xx xx xx xx ......Realtek PCIe GBE Family Controller
1...........................Software Loopback Interface 1
[code]....
Both of these stations are running Windows 7.So essentially what I am trying to do here is route all traffic to the 10.zzz.zzz.0 subnet through the 10.xxx.xxx.147 gateway. Everything else should go through the 10.xxx.xxx.230 gateway. This is the intended behavior, and again it is working everywhere but that one station.
View 4 Replies
View Related
Jan 2, 2012
I need to be able to redirect some HTTP traffic to an Ironport WSA (for now) on a DMZ interface, the initial config I'm trying to test is along the lines of the following (don't have access to the ASA at the moment to cut-and-paste):
access-list 101 deny any any neq www
access-list 101 deny tcp host 10.0.2.2 any
access-list 101 permit tcp any any
route-map proxy-redirect permit 101
match ip address 101
set ip next-hop 10.0.2.2
Unfortunately the ASA does not take the "set ip next-hop" command, I get an invalid input error message and if I at the route map config prompt type "?" only the "metric" and "metric-type" commands are listed as available.
This happens both on 8.2 (ASA5510) and 8.4(2) (ASA5505). Since others are able to make this work, I assume there's something else on the ASA that I have to set to enable this command?
View 2 Replies
View Related
Mar 20, 2013
I have an internal DVR system that I am trying to share to the outside world. We recently put in an ASA5505 and I am having trouble getting the settings correct.I want to use an external IP to access the DVR system from anywhere and have my ASA5505 redirect the traffic to the internal IP address. I assume I need to use a NAT and a route policy however can not figure out how it would be.
View 11 Replies
View Related
Nov 10, 2011
I have two ASA 5505 on two different locations(main office and remote office) and I need the remote office to be in the same subnet as the main office since they move computers betweend the offices and they have fixed IP addresses on those computers and they have no right to cahnge to dhcp mode when they move to remore office. Is it possible to create like a bridge over the VPN tunnel so it extens the LAN ?
View 18 Replies
View Related
Oct 13, 2012
I config the routers with EIGRP and also write Static route between two PC before remove the link between router0 and router1 , destination is reachable , but when remove this connection , packet from pc1 to pc0 will drop in a loop and never reach to destination , is it possible to have a Link state routing protocol and static route at the same network like this scenario , how to prevent loop in this topology static route is configure as bellow :
router0 <==> router 1 <==> router2 <==> router3 <==> router <==>pc1
View 6 Replies
View Related
Dec 7, 2011
I have a new Cisco 819 router wtih Verizon 3G built in. I want to use this router to provide 3G backup Internet access for a customer kiosk. The 3G is perfectly stable when I use it as a primary, static routed connection. When I use a floating static route, the link goes up and down constantly. The 3G link works for a about 20- 30 seconds, then goes to reset, down, then dials up and reconnects.
View 2 Replies
View Related
Dec 6, 2010
I have a nat and vpn setup on my Cisco 2801 router.Everything is working as expected except the NAT. I have a single static nat translation but it only works for inbound and not outbound. Going outbound, it uses the default overload nat address of the outside interface. [code] I want to add another mailserver. But I fear if one mailserver were to get black-listed, they would both be reporting there ip address as the same address (the one on the ethernet interface) which would blacklist both mail servers.Again, inbound nat works ok, but outbound is just using the IP of the ethernet0/0 address.
View 2 Replies
View Related
Mar 12, 2013
In my Lab environment in GNS I have connected two 7200 series router through fastethernet on router A I have given IP adress 192.168.10.54 and router B I have given IP address 192.168.10.53 and default route as 0.0.0.0 0.0.0.0 192.168.10.53 and when I run the command on router A it shows result as follows "C 192.168.10.52/24 is directly connected ,Fast ethernet 2/0".
So I need to know why it's showing the result of .52 at last why not .53 or .54 at last what is the reason it's showing .52 which I have not mentioned in my IP address.
View 5 Replies
View Related
Jan 13, 2013
We have a customer, who has the following setup:
ISP router with ip range: x.x.202.1/ 28
That is connected to a Cisco 2960 switch, that doesn't do much but:
Vlan5: x.x.202.14 /28
Port 1-12 is switchport mode access to vlan 5 There are 3 firewall's connected to the 2960
1: D-Link DSR-1000N with ip x.x.202.2 /28
gw: x.x.202.1
2: Uknown
3: Cisco ASA 5505 with ip: x.x202.7 /28
static route: x.x.202.1
Each FW have a LAN behind it. The D-Link and the unknown device are both working perfectly and clients on each subnet can connect to the internet?However when I connect the ASA 5505 to the 2960 SW with a configued static route: Route Outside 0.0.0.0 0.0.0.0 x.x.202.1 1 is says it has no route to host?
Sanitized Config for the ASA 5505 is:
hostname ciscoasa
domain-name network.local
names
!
interface Ethernet0/0
switchport access vlan 2
[code]....
If I connect the ASA5505 to the LAN of D-Link DSR-1000N and give it a static address and a static route match the D-Link LAN network, it works perfectly, however not when I connect it the the Cisco 2960 Switch
View 2 Replies
View Related
Feb 20, 2012
I have a Cisco 1841 with a DSL and 3G HWIC interface. I would like to setup the DSL as the primary link and then use the 3G as a backup interface. I am trying to accomplish this using the Floating Static routes with SLA object tracking.
I have tried various options, like having two tracked routes, one tracked route, changing administrative distances, multiple SLA's, etc etc.
My problem basically is that when the DSL (Dialer0) goes down and the 3G (Cellular0/1/0) takes over, that the SLA never changes back when the DSL is available again, so that the DSL can take over as the primary link again. [code]
View 3 Replies
View Related
Sep 11, 2012
Add static route for new exchange server?
View 1 Replies
View Related
Oct 16, 2012
Cisco device is neighbored up with a Brocade device via OSPF, and the desired routes are present.This Brocade device is neighbored up with another Brocade device via OSPF over a GRE tunnel. I am not seeing the desired routes present.What kinds of things can I look at to determine the issue? I think I've viewed the OSPF topology database (I'm not that familiar with Brocade) with the show ip ospf routes command and I'm not seeing the desired routes there either.There is no form of route filtering in place. I'll double check, but I do not believe there is any stub routing going on either.
View 12 Replies
View Related
Jun 6, 2011
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
View 1 Replies
View Related
Jun 29, 2011
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies
View Related
Jun 15, 2012
I'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies
View Related
Jan 30, 2012
We have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
View 21 Replies
View Related
Nov 27, 2011
I have set up an ipsec tunnel between a Cisco ASA 5505 and a Fortigate 80c. The tunnel is set up as I execute pings from inside behind ASA to inside behind FG, however I cannot get connectivity to hosts behind the Fortigate (traffic is allowed through policies configured on the FG). What I noticed in packet tracer is that traffic is dropped at the step 'Vpn lookup' To troubleshoot I have configured a test ('fake') vpn connection through the vpn wizard and get the same result in packet tracer. I run 8.4 software on the ASA and this is part of the relevant config.
View 1 Replies
View Related
Aug 9, 2012
I'm having trouble configuring an ASA5505 on version 8.31 code for an IPSec tunnel. I've done this multiple times on 8.2.5 but can't seem to get my tunnel to even attempt to come up on this ASA. Not sure if it's relevent or not, but this remote ASA has never been used for another VPN tunnel before. When I attempt to ping a host on the other side of my tunnel, I just see the following: 8108# sho crypto isa sa
There are no isakmp sas
My local network is 10.1.1.X/24 and my remote peer network contains 66.37.227.X/24. I've been working on this for the better part of the day and would love to get it resolved.
View 8 Replies
View Related
May 20, 2012
I have a number of sites in China, they have decent inter-country connectivity but poor connectivity when going overseas.
We have a single site in China witha dedicated 1:1 leased line that has good conectivity both inside and outside of China.
All the sites in China have ASA5505 firewalls
One of our Citrix farms is hosted in the UK and although the main site with the leased line is fine accessing the farm the other sites are not. I would like to try and tunnel just the citrix connectivity via a VPN to the China head office then use their connection to get out to the farm.
how to tunnel all traffic but not just specific traffic over the VPN.
View 3 Replies
View Related
Feb 13, 2011
I am setting up a remote site to provide a backup internet circuit for outbound traffic. Everything is working from the main site by redistributing a static route and using default-information originate within BGP to my MPLS provider.Now on the remote site I setup a static route with an AD of 250 which is higher than the AD of 20 we are getting from the main site over the MPLS network. When the route come up BGP uses the default route from the main site and everything works fine. When I clear the BGP routes at the main site the backup site installs the static route with a higher AD. The problem is when the BGP route comes back up the static route is not getting removed. From looking at some other posts it seems that the redistributed local route is still preferred by BGP. They mentioned setting the weight to 0 in a route map which I tried but I am not getting the results of removing the static route and using the BGP route.Remote site router config: router bgp 65011. [code]
View 24 Replies
View Related
May 8, 2011
My 2811 is connected with two ISP,s as below and have VPN with Central branch.I want to set DSL as primary and WiMax as secondary but problem is that routes learned via BGP get precedence over default route as they are specific one.I think i may need to put all static specific routes of central branch over DSL along defautl but I want any idea if my default route stay active and when it down then BGP neighborship can be establish (like ip sla tracking.)
View 3 Replies
View Related
Apr 2, 2013
I have Cisco RV180. I can not set static route with destination to all IPs (0.0.0.0/0.0.0.0). It always shows errors. It asked me to input non zero number. I can do this on Cisco RV042 without any problem.
View 3 Replies
View Related
Feb 23, 2010
Have a solution with PFR with two master controller in hsrp mode and two active border controller, betwen the MC and the BR i'm running EIGRP. The two BR have BGP to the ISP but i have default router for the parent route. Same weeks ago i notice some problems in reaching to specific public ip addr. During the trobleshooting i found that the two border controller have dynamic-pbr applyed to the inside interfaces and one of the satement on the dynamic route-map is setting the next-hop for the destination public ip addr yhe inside interface on the two border routers. This way the traffic is looping betewn the two BR. It's possibel do disable the PIRO (PBR) and only to use static route injection betwen the MC and BR.
The routers are running 12.4.24T
View 1 Replies
View Related
