Cisco WAN :: 819 Not Able To Route Through VPN Tunnel
Jan 20, 2013
I have a Cisco 819 router and it's the first time I've configured any Cisco product. Starting from scratch, I have managed to get 3G working and the VPN to connect but so far no packets can route down the VPN tunnel (the other side is openswan/shorewall on CentOS5).I've been pawing over lots of guides and forum discussions but seem to be a bit lost. I suspect I'm missing some access-list definitions but don't really know how to go about it. I want the network behind the Cisco 819 (10.x.x.0/20) to be able to access the internet through the interface Cellular 0 but also the VPN remote network (192.y.y.0/24)When I ping from the other (non-cisco) end I see on the Cisco 819.
View 9 Replies
ADVERTISEMENT
Oct 16, 2012
Cisco device is neighbored up with a Brocade device via OSPF, and the desired routes are present.This Brocade device is neighbored up with another Brocade device via OSPF over a GRE tunnel. I am not seeing the desired routes present.What kinds of things can I look at to determine the issue? I think I've viewed the OSPF topology database (I'm not that familiar with Brocade) with the show ip ospf routes command and I'm not seeing the desired routes there either.There is no form of route filtering in place. I'll double check, but I do not believe there is any stub routing going on either.
View 12 Replies
View Related
Feb 14, 2011
Got a problem routing trafic to my L2L tunnel...
Got an ASA5505 Sec+ with ip 10.45.10.1 on inside interface. Firmware 8.3(1). Got another Cisco router (From my ISP) with ip 10.45.10.254 - This one creates an L2L tunnel - To the 10.45.20.0/24 net.
On the 5505 ive got "route inside 10.45.20.0 255.255.255.0 10.45.10.254 1", and trafic is being directed to 10.45.10.254 as it should.
I know cause I can ping everything one the 10.45.20.0/24 net - But thats it... Cant RDP, connect to fileshare... Nothing.
When i test a PC and set it to gateway 10.45.10.254 I can access everything on the remote network. Do I need some NAT command or an access-list? I've setup AnyConnect VPN on the ASA and I can connect to both networks without any problems.
View 2 Replies
View Related
Jun 6, 2011
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
View 1 Replies
View Related
Jun 29, 2011
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies
View Related
Jun 15, 2012
I'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies
View Related
Jan 30, 2012
We have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
View 21 Replies
View Related
Mar 17, 2011
We have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 Replies
View Related
Aug 14, 2012
i measured with Iperf over two Cisco 1811 router, that bandwidth speed is higher then is used IPsec+GRE tunnel between two routers, than just using a static routes.Bandwidth over GRE in average is about 91389Kbit/sec Over static routes is about 88474Kbit/sec.
View 1 Replies
View Related
Nov 10, 2007
I have set-up a Linksys BEFVP41 VPN router at home (192.168.1.1 / 255.255.255.0)
View 7 Replies
View Related
Oct 9, 2012
I have a Cisco 527w which we are wanting to deploy to our remote sites however i've found a bug. We use ADSL with an IPsec tunnel as primary and 3G APN for failover . When the ADSL goes down the route via the IPSec tunnel remains and i am unable to route the traffic via the APN backup without disabling the VPN tunnel .
View 0 Replies
View Related
Jun 24, 2011
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
View 1 Replies
View Related
Jan 9, 2011
i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies
View Related
Sep 23, 2012
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
Jan 23, 2012
There are a few situations were I'd like to be able to use the locally configured account on a device but still have ACS in place.I want to complete this WITHOUT adding the locally configured account into ACS.I have tried setting the advanced option under Identity for if an account is not found to "Continue" however this causes the account to be allowed as long as a password is typed (any password, as long as its not blank).
View 2 Replies
View Related
Aug 6, 2012
I have a NAT/Port Forwarding going on for which I need to deny all traffic except the one mentioned in my ACL/route-map, So, port forwarding from host A to host B, all else, deny. The port forwarding works, but for some reason.
View 2 Replies
View Related
Dec 8, 2011
I'm trying to setup an 877 to sit in front of a firewall. As the firewall has a public IP I do not want to use NAT. The problem I'm having is I can't seem to route through the 877. From the 877 i can ping 8.8.8.8 From the internal network I can ping the dialer0 interface of the 877 but cannot ping 8.8.8.8
View 2 Replies
View Related
Aug 29, 2012
why a subnet wouldn't be passed on to just one participating OSPF device?
I have two routers and an ASA, all of which are in area 0, it's a pretty simple config. The two routers are connected to some other devices (also in area 0) that pass of an external route to a particular subnet, let's call it 192.168.4.0. The routers are getting it just fine, but the ASA is not:
View 8 Replies
View Related
Jan 4, 2013
I am a bit green with IOS and have exhausted everything I can think of with this. The router passes the WAN test in CCP?Undoubtedly there are probably a few things in the config that are either redundant or totally unnecessary, but I have been trying a few things to solve this with very little success.I have no security stuff in here because I have triewd to keep the config as simple as possible to start with. I will add that after I get the routing working.
Here is my most recent config:
Cisco871W#show config
Using 2631 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[codde].....
View 4 Replies
View Related
Nov 15, 2012
Configured cisco 881, WAN has static IP address and LAN is nothing fancy. I can ping out to url... or anywhere from the router but cannot from LAN client computers. [code]
View 4 Replies
View Related
Mar 2, 2011
I am attaching my current network topology, My problem is that i am having mpls & p2p link terminated on the 7206 router left side of diagram. now my problem is if i apply PBR on this 7206 router & tracer any host which are on right side of the diagram, it drops on IP 10.1.1.1..ideally it should go to my Core switch on right of the diagram.
View 8 Replies
View Related
Feb 27, 2013
I configured dns on the router on this command ip name-server 4.2.2.2when i tried to ping www.google.com showing no valid routeTranslating "www.google.com"...domain server (4.2.2.2) [OK]Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 2800:3F0:4001:807::1013, timeout is 2 seconds:
View 9 Replies
View Related
May 7, 2012
I am trying to track down a device that's blocking a certain port I know there are programs out there than will do a trace-route that's on TCP but is there any programs that allow you to specify a port?
View 6 Replies
View Related
Jul 3, 2012
Is there any way to route inject with RRI only when the VPN is formed on an ASA ?
View 5 Replies
View Related
Jul 1, 2012
I want to leak default internet route to CE VRF as common service.Since we having two ASBR, can I point next hop to PE itself instead of either of the ASBR?I tried to point NH to loopback of the PE itself but it failed.
View 6 Replies
View Related
Aug 2, 2012
a) one router with two ethernet interfaces (LANs) and a serial interface. The serial interface is connected to the internet, dynamic nat is used for hosts in the two lans. A web server has a private address of 172.168.50.10 and it is being translated to the internet with serial's interface 68.32.x.x (public ip) with static nat. Clients in the internet type the public address to access the web server.
b)Problem: clients inside the LANs cannot access the web server by typing the public address, they use the server's private address instead, this create a problem with DNS static entries in the HOSTS file in the OS. It is a test server and is only available to authenticated users (lock and key ACLs), so no need to make a real DNS record. The entry in the HOSTS file points to the public address.
c)Question: how can a create a route map to change the public address in the HOST file to the private address of the test web server everytime a user in the LANs type the domain name.
View 6 Replies
View Related
Mar 4, 2013
I am advertising the 172.16.10.0 network from R5 to R1 via EBGP. The problem is that on the Router R1 I see the route 172.16.10.0 whith show ip bgp command but in the show ip route don't appear.I thinked that the problem was SYNCHRONIZATION,so that will activated synchronization on the routers R1 and R4 but don't work. Furthermore the routers R2 and R3 neither receive the route via OSPF.
View 11 Replies
View Related
Nov 6, 2012
I know RD is used to make an IPv4 address unique in an MPLS VPN system.I don't understand why a PE sends the RD when advertises a route via BGP.I thought RD were only local significant. But I made a packet capture and the RD is actually sended inside the MP_REACH_NRLI attribute:
(from packet capture)
Label Stack=19 (bottom) RD=12:1, IPv4=172.16.22.0/24
MP Reach NLRI Route Distinguisher: 12:1
Why the RD is sent? I suppose that the PE receiving the update checks the Route Target Extended Community to know to which VRF associate the update and not the RD.I made a test between PE1 with RD 12:1 and PE2 with RD 13:1 and there was full routes exchanges, the same when both PEs were using the same RD(all this configured in the correct VRFs). The only difference is that PE2 now shows in their corresponding VRF BPG table "Route Distinguisher 13:1".
View 19 Replies
View Related
Dec 13, 2010
We have a Cisco 1841 router and checked something an unnusual (never seen before) routing table having L - local routes. if this an IOS bug or same as C - connected local routes.
1841#sh verCisco IOS Software,
1841 Software (C1841-IPBASE-M),
Version 15.0(1)M3, RELEASE SOFTWARE (fc2)Technical Support: [URL] ... Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Sun 18-Jul-10 01:16 by prod_rel_team
[Code] .....
View 6 Replies
View Related
Dec 23, 2011
I have a 2801 with dual ISP connections, and I have configured route-maps to direct voice traffic over ISP1 (working just fine), and I'm attempting send all other traffic over ISP2 (traffic is load-balancing instead). The connection to ISP2 is DHCP, and I have configured a route-map to route this traffic using the 'ip next-hop dynamic dhcp' command, but when I look at the route-map, it states the following: ip next-hop dynamic dhcp - current value is UNKNOWN..Is there something that I need to enable in order to see the next-hop, and properly send traffic over the ISP2 connection? [code]
View 9 Replies
View Related
Nov 1, 2012
I have pix firewall 525, configured with ospf process. We are also performing route filetering in ospf process using route-map. Now we want to remove this route-map from ospf process. Any step-by-step process for removing route map as per below list. How to remove route-map without having any impact as per above configuration.
View 1 Replies
View Related
