Home Network :: How To Route All Traffic Only Via VPN
Aug 21, 2011
I am using OPEN VPN in order to connect to a Canadian VPN server.I want ALL internet traffic to ONLY use the VPN connection and no traffic shall pass through my local ISP under any circumstance.In the event the VPN disconnects, I DO NOT want any internet traffic automatically sent via my LOCAL ISP connection. Can I simply disable my LAN network adapter in windows AFTER the vpn is connected? (since vpn uses its own TAP adapter?)
View 2 Replies
ADVERTISEMENT
Jun 6, 2012
My laptop have 2 NIC attach it, the cable NIC and Wireless NIC, the cable one connect to my lab network environment and the Wireless connect to office network environment (connect to internet) which both have differen segments [code] when my Wireless was turn off my pc can ping to all segment on my lab network environment, but if the wireless was turn on, i cant ping to others segment but only my laptop segment and i still could surfing to the internet without any problem.then i tried to add a new route from my laptop using "route add x.x.x.x mask x.x.x.x (gateway)" in command line and after that i can ping back to all segment in my lab network environment eventhough my wireless was onwhy i have to create a manual route into my laptop so that i can have connection between my laptop and my lab environment in the condition my wireless turn on ??
View 8 Replies
View Related
Oct 11, 2012
I work in a small village in Africa and Interent access is often very unreliableTherefore I have 3 different ways of accessing the Interent from my home.The cheapest is Wifi from a local provider, but that doesn't always work. More expensive and still often unreliable is a 3G access. Then, when WiFi and 3G don't work I still can access the Internet via a Inmarsat BGAN satellite terminal, but that is very expensive.What I'd like do is to connect several computers to the same WiFi, 3G, BGAN Satellite Interent (all Ethernet) access via a home WiFi network.Now the questions I have:- can I just connect everything to a switch and then to the Wan-port of a wireless router?- how do the prioritisation works? When there is 3G available, I dont want to access the Internet via the BGAN, bacause that's too expensive?
View 2 Replies
View Related
Mar 22, 2011
I have the above router on 10.10.10.1 which I'm quite familiar with but I need reaching a VM residing on one of my internal MAC's. My cisco route table is as follows:
Gateway of last resort is 93.97.20.1 to network 0.0.0.0
93.0.0.0/21 is subnetted, 1 subnets
C 93.97.16.0 is directly connected, ATM0.1
10.0.0.0/24 is subnetted, 1 subnets
C 10.10.10.0 is directly connected, BVI1
S* 0.0.0.0/0 [1/0] via 93.97.20.1
The internal physical machine that contains the VM is 10.10.10.9 whose routing table is:
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 10.10.10.1 UGSc 6 8 en0
10.10.10/24 link#4 UCS 5 0 en0
10.10.10.1 0:1b:2b:cc:7:8a UHLWI 7 1248 en0 284
10.10.10.9 127.0.0.1 UHS 0 86171 lo0
10.10.10.11 0:23:54:2a:6:d3 UHLWI 0 234 en0 150
10.10.10.30 0:9:34:28:60:2e UHLWI 0 25 en0 857
10.10.10.111 0:1d:ec:2:2d:2d UHLWI 1 1599 en0 721
10.10.10.255 link#4 UHLWbI 2 18609 en0
10.37.129/24 link#8 UC 2 0 vnic1
10.37.129.2 0:1c:42:0:0:9 UHLWI 1 2 lo0
10.37.129.255 link#8 UHLWbI 2 14046 vnic1
10.211.55/24 link#7 UC 2 0 vnic0
10.211.55.2 0:1c:42:0:0:8 UHLWI 0 2 lo0
10.211.55.255 link#7 UHLWbI 2 14046 vnic0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 5 214223 lo0
169.254 link#4 UCS 0 0 en0
The VM has a static IP of 10.211.55.5 and can obviously ping out to the rest of my lan but as of yet my router and other machines on the 10.10.10/24 subnet cannot reach the VM. I sort of presume this is a simple task of adding some kind of static route on my router and then all other machine will know how to get to the VM. So what do I need to do as I have about 40 or so customers already connected of whom I do not wish to suddenly halt their access due to my inexperienced attempts to create this route or new link(s)
View 1 Replies
View Related
Jun 21, 2012
is it possible for a client to choose a WAN to use when being routed through a Multi-WAN router? Something that could be configured as default route in linux or default gateway in winxp ?Or is this decision totally up to the router itself ? [code] Could now a client on the subnet 192.168.0.0/24 choose 1.1.1.1 as a default route for example? And if not, could this be possible if the router hat some secondary internal IPs for both WAN interfaces.
View 3 Replies
View Related
Aug 22, 2012
i have a vpn and want to test the way traffic goes when i connect and disconnect vpn try some stuf, how can i see where my info is transiting , i want to test my vpn reactions to changes ill do.
View 1 Replies
View Related
May 12, 2011
So a BT home hub is a very cheap router, so it seems. And - if you connect a quite a lot of eq to this router, it starts crashing. "It can't handle the traffic.". But what does that mean? Why can it handle the traffic for a while and after a few days it can't anymore. And lets say - some of the eq doesn't really work on the external network, it works on the internal network, and it doesn't need the internet to work for proper functionality. So - what is important then? Which specifications are the important ones?
View 2 Replies
View Related
Jun 6, 2011
We have a small download limit every month and keep ramming into only days into our billing period. I am trying to identify the culprit but need to find a way to log the traffic of individual IP address (which are all static) on the network to figure out where all the bandwidth is going. Any (preferably free) application that will allow me to monitor this?
Network Infrastructure:
Modem connected to NetGear N2000 (older model) Router 192.168.0.1
Family Desktop - 0.2 (Ethernet)
My Desktop - 0.3 (Powerline Ethernet)
Brothers Laptop - 0.5 (Wireless)
My PS3 - .0.30 (Wireless)
iPods - (Wireless)
Router only tells me when someone is on and can track total network traffic usage not individual hardware.
View 2 Replies
View Related
Sep 5, 2012
wondering if redirection or conversion port 8080 into port 80 is possible? if so how and what cisco equipment can do that?
View 11 Replies
View Related
Feb 23, 2011
I have a router that supports wireless network. I have 2 desktop computers that connect through LAN, 3 Laptops that connect using WiFi. Lot of them use utorrent. I want to block it. They use it to download movies. I have warned them of consequences but they simply dont listen. I dont know how to implement QoS in my router. Mine is UTStarCom.
View 1 Replies
View Related
Nov 15, 2012
Configured cisco 881, WAN has static IP address and LAN is nothing fancy. I can ping out to url... or anywhere from the router but cannot from LAN client computers. [code]
View 4 Replies
View Related
Apr 5, 2012
I have a media player wired to my dir-655. I have a wrt300 on the same network to use for vpn. I live in Canada, and to use Netflix etc, from the US, I need to use the vpn.Is it possible to have the media player routed through the wrt300, rather than discovering all the IP addresses for Netflix etc and routing each one?
View 3 Replies
View Related
Apr 19, 2010
I have a 2821 router with two T1 WICs and have the need to route FTP down one T1 and all other TCP traffic down another T1. All traffic is going to the same remote IP address. The remote sites are in different states, and I assume that the remote subnet is being bridged between the states. It's kind of a weird set up, but it's not my design.
Anyway, can I use a route map to split off FTP traffic to host A and send it down one T1 and have the rest of the IP traffic to host A go down the other T1? I also need to be able to have all traffic use one T1 in case the other T1 goes down.
My first thought was to static all IP down T1-1, then route map FTP traffic down T1-2, then have a floating static for all IP traffic down T1-2 with a higher metric. But something would have to track the T1 interfaces and I'm not sure if route maps or static routes can do that. Any thoughts on this?
View 2 Replies
View Related
Dec 3, 2012
Is it possible with the DIR-601 to have one of the IP's on the LAN route all traffic through a proxy server? I would like to have my Roku device (which I've setup as a static on the LAN side) to always connect though a proxy, while all my other devices connect to the internet normally.
View 3 Replies
View Related
Sep 12, 2012
I currently have a site to site VPN running connecting a branch office and the Main office using a ASA5510 and ASA 5505. currently PC's at the branch can access the network in the main office using interface 0/1, but we have added another ip range using interface 0/2 and I can't seem to route the traffic to both interfaces. I currently have 0/1 as inside 192.168.10.1 which works, and have added 0/2 as Inside2 192.168.20.1. I know I am forgetting something, any commands to route incoming VPN traffic so PC's at the branch office can connect to both IP ranges?
View 14 Replies
View Related
Feb 18, 2012
The router passes the Interface test for the WAN port in CCP but it still we cannot access the internet. Here is my configuration:
Building configuration...
Current configuration : 3663 bytes
!
! Last configuration change at 09:29:52 Chicago Mon Feb 20 2012 by fbcpekin
version 15.1
[Code].......
View 5 Replies
View Related
Jun 27, 2012
I want to route gre traffic through an ACE20, but it doesn't seem to work. The only thing I configured was an ACL with gre enabled, but the ACE20 seems to drop the gre packtes. The gre traffic is entering via the vlan 561 interface and should be send out via the vlan 472 interface. Source 10.94.32.212, destination 10.94.132.39. The tunnel control traffic on port tcp/1723 is working fine. In the service-policies is nothing configured for the gre traffic.
Code...
View 1 Replies
View Related
Jun 6, 2011
I have a two RV042 VPN Router, I successfully connected the IPSEC tunnel. I cannot route Traffic in the tunnel. See the diagram.
MAIN Network
10.252.x.x
-------------->
FIREWALL
a.a.a.1
INTERNET
RV042a WANa <<------------------------------->> WANb RV042b
a.a.a.2 b.b.b.b
In this manner the network of b.b.b.b wil connect to the Main Network 10.252.x.x, unfortunately I can't pass traffic to RV042b going to RV042a. Everytime I trace the route, the traffic goes outside the Internet not to RV042a.
View 1 Replies
View Related
Jun 29, 2011
I need to route traffic to DMZ (and internal) from the branch office thru the IPSec tunnel. How do I manage that with my Cisco 881?
View 1 Replies
View Related
Jun 15, 2012
I'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies
View Related
Apr 23, 2012
I am trying to configure dual ISP on my ASA5505.I have everything configured and working when eth0/0 is connected, but when I disconnect it, it doesn't route any traffic.The static route for the primary isp is removed and the static route to the backup isp shows up, but no traffic goes in or out. I should note that I'm doing this as a proof of concept so eth0/0 is connected to a router and eth0/1 is connected to another router. [code]
View 7 Replies
View Related
Jan 30, 2012
We have 7 remote offices and 10 tower locations that utilize IPsec tunnels back to our HQ. We now want to force all traffic including web surfing through the tunnels. What would be the easiest way to acomplish this? I have tried utilizing the crypto map policy to do this, but was unable to acomplish this.
Each of our office locationss utilize a Cisco 2811 router and the tower locations utilize a Cisco 881.
View 21 Replies
View Related
Oct 5, 2011
i want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies
View Related
Nov 18, 2011
I have a customer which has a main location office and a remote one. Recently we interconnect their facilities using a local ISP service called Virtual Connectivity, which basically is a private network which can be accessed over aDSL or any other data circuit. They are using Cisco 888 routers to interconnect both sites.At the main site the customer also has an Internet circuit (with a Cisco 857 router)and he wants to remove the Internet circtuit from the remote site and provide them access over their main location Internet circuit.At the primary offices, we installed Cisco 2811 router as a gateway to route the Internet and remote network traffic over the required data circuit. Everything is working fine, but we can not access Internet from the remote location over the circuit installed a the main site. I understand this is a routing issue, since the traffic hits the main office network it does not knows how to reach the Internet. I am assuming this routing must be set into the main office Cisco 888 router (installed by the ISP to interconnect to their private cloud) in order to properly route it over the Internet circuit.Since I already have access over the Internet router and the gateway router at the main site, but not into the ISP router, is there any other way I can make this configurtion over the routers I already have access?
View 3 Replies
View Related
Nov 22, 2011
I am working for a company based in Sydney Australia, the company recently open an office in London UK, therefore we are going to get leased lined based on MPLS.We were advised that Customer Edge router will be CISCO1941/K9. We want to our UK client to access our web-based applications via MPLS network instead of internet. The UK office is using BT Business ADSL with 5 Static IP address (please note the modem IP address is actually dynamic), we are going to get a Cisco 857/K9 router which will be used for the entry for the UK client to access the MPLS network. My question will be how do I configure the Cisco 857 router to allow one of the public ip to access the MPLS network. It appears that there are two options, and I am not sure if this is going to work or which one is working better. I have attached two diagrams for clarification of my case.
Option 1 Cisco WAN interface get Dynamic IP (PPPoA) from BT LAN Interface (4 Port) get the assigned 5 Static IP addresses One of the five IPs (217.xx.xx.169) will be assigned to the FE1 (Cisco 1941), any traffic to 217.xx.xx.169 will be routed to the WAN interface of Cisco 1941 to access Sydney service (located in Sydney LAN, mostly http and https traffic) One of the five IPs to 217.xx.xx.170 will be assigned to the WAN interface of Sonicwall Firewall Router which also serve as Internet Access Gateway for LAN users, All trafiic destined for Sydney LAN will be using FE0 (Cisco 1941) as gateway
Option 2Cisco WAN interface get Dynamic IP (PPPoA) from BT LAN Interface (4 Port) will get 192.168.0.1, Cisco 857 router will be the default gateway for LAN users, using one to many NAT, also one to one NAT, One of the five IPs (217.xx.xx.169) will be forwarded to the FE0 (Cisco 1941), any traffic to 217.xx.xx.169 will be routed to the WAN interface of Cisco 1941 to access Sydney service (located in Sydney LAN, mostly http and https traffic)
View 4 Replies
View Related
Dec 15, 2011
All of my remote sites use various routers to route all of their traffic via IPsec. However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel. My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway. When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.
View 3 Replies
View Related
Mar 24, 2013
Just picked up a ISA550 and have been playing around with it a bit but seem to be having some trouble. I have two LAN subnets in my small business with approx 10 hosts per subnet. I'd like to use the ISA550 to route between them (and to the internet) but can't seem to figure out how. Is it just as simple as creating two VLANS? Can the ISA550 route VLAN traffic?With my old RV042G, I had the option to setup multiple subnets inside the setup menu but I don't see any such area with the 550.
View 2 Replies
View Related
Mar 17, 2011
We have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 Replies
View Related
Nov 13, 2011
We have multiple vpn tunnels coming to our cisco asa 5520 , the problem is that when we create another tunnel with the same network as another network on the firewall , it does not know how to route the traffic to which interface or sub interface.
View 2 Replies
View Related
Jul 31, 2012
I have an ASa 5510 and setup remote dial in users.
I wanted to use the windows 7 built in client and also the draytek site to site VPN options however when they connect VPN traffic will not work however when i use the cisco VPN client then everything works fine.
All the VPN's connect pretty quickly.In the syslog I a getting errors when i try and ping something: [code]
View 2 Replies
View Related
May 30, 2011
I have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
View 10 Replies
View Related
Jan 31, 2013
The X3000 functions as a router/gateway between the ADSL network, its wireless network (WPA2) and its wired network. After a cold start, factory reset and restore of the config file everything works fine. I have interconnection between all three parts of my network. However after ± 24 hour there is no connection possible anymore from the wired to the wireless network and vice versa. A normal power off - power on will not work. The only thing that works is running the factory reset procedure as discribed above. I changed the MTU to manual 1400 as was suggested on this forum, but that does not work. Apart from this issue, ADSL is hicks sometimes. From my ISP I heard that at certain times my router issues ten's of DHCP requests within one minute, while the connection (modem) remains perfect. I have the impression that after such a DHCP request storm to my ISP, the interconnection between my X3000 wireless network and my X3000 wired network is lost.
View 4 Replies
View Related
Nov 10, 2007
I have set-up a Linksys BEFVP41 VPN router at home (192.168.1.1 / 255.255.255.0)
View 7 Replies
View Related
