Home Network :: Cisco 877W - Create Route Or New Link(s)?
Mar 22, 2011
I have the above router on 10.10.10.1 which I'm quite familiar with but I need reaching a VM residing on one of my internal MAC's. My cisco route table is as follows:
Gateway of last resort is 93.97.20.1 to network 0.0.0.0
93.0.0.0/21 is subnetted, 1 subnets
C 93.97.16.0 is directly connected, ATM0.1
10.0.0.0/24 is subnetted, 1 subnets
C 10.10.10.0 is directly connected, BVI1
S* 0.0.0.0/0 [1/0] via 93.97.20.1
The internal physical machine that contains the VM is 10.10.10.9 whose routing table is:
The VM has a static IP of 10.211.55.5 and can obviously ping out to the rest of my lan but as of yet my router and other machines on the 10.10.10/24 subnet cannot reach the VM. I sort of presume this is a simple task of adding some kind of static route on my router and then all other machine will know how to get to the VM. So what do I need to do as I have about 40 or so customers already connected of whom I do not wish to suddenly halt their access due to my inexperienced attempts to create this route or new link(s)
My laptop have 2 NIC attach it, the cable NIC and Wireless NIC, the cable one connect to my lab network environment and the Wireless connect to office network environment (connect to internet) which both have differen segments [code] when my Wireless was turn off my pc can ping to all segment on my lab network environment, but if the wireless was turn on, i cant ping to others segment but only my laptop segment and i still could surfing to the internet without any problem.then i tried to add a new route from my laptop using "route add x.x.x.x mask x.x.x.x (gateway)" in command line and after that i can ping back to all segment in my lab network environment eventhough my wireless was onwhy i have to create a manual route into my laptop so that i can have connection between my laptop and my lab environment in the condition my wireless turn on ??
I'm trying to create a route from a VPN ip to the VPN server in my LAN. Anyhow, the DIR-655 does not let me create routing within the LAN (since only the WAN interface option is available).I have tried with the following firmwares: 1.11, 1.21, 1.30.
I am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
I am trying to create a VPN on my Mac that I can access from my iPad in a remote location (work.) I have been using "iVPN" on the Mac to "distribute" the home Mac's Internet connection to the iPad. I have everything set up right and the VPN works fine and the iPad connects fine, just not when I am work, where I want it to work. The iPad tells me that it cannot connect to the VPN. I believe my work blocks VPN ports (1701, 1723 etc) I can do a google search from the iPad on the work WiFi so the connection is ok, but I believe those ports are blocked. If I connect the iPad to a restaurant's wifi for example, the VPN connects fine. What client can I use to create my own VPN at home where I can use a standard port like port 80 or something that is not blocked at work so that I can connect to the VPN from work?
I am using OPEN VPN in order to connect to a Canadian VPN server.I want ALL internet traffic to ONLY use the VPN connection and no traffic shall pass through my local ISP under any circumstance.In the event the VPN disconnects, I DO NOT want any internet traffic automatically sent via my LOCAL ISP connection. Can I simply disable my LAN network adapter in windows AFTER the vpn is connected? (since vpn uses its own TAP adapter?)
I have a home network using a 2600 and PIX515E, and unfortunetly I don't know how to set up ACLs. I read a few Cisco documentation but unfortunetly I am unable to grasp the concept of how to define them. Would anyone be able to give me a crash course on setting up ACLs?
I work in a small village in Africa and Interent access is often very unreliableTherefore I have 3 different ways of accessing the Interent from my home.The cheapest is Wifi from a local provider, but that doesn't always work. More expensive and still often unreliable is a 3G access. Then, when WiFi and 3G don't work I still can access the Internet via a Inmarsat BGAN satellite terminal, but that is very expensive.What I'd like do is to connect several computers to the same WiFi, 3G, BGAN Satellite Interent (all Ethernet) access via a home WiFi network.Now the questions I have:- can I just connect everything to a switch and then to the Wan-port of a wireless router?- how do the prioritisation works? When there is 3G available, I dont want to access the Internet via the BGAN, bacause that's too expensive?
is it possible for a client to choose a WAN to use when being routed through a Multi-WAN router? Something that could be configured as default route in linux or default gateway in winxp ?Or is this decision totally up to the router itself ? [code] Could now a client on the subnet 192.168.0.0/24 choose 1.1.1.1 as a default route for example? And if not, could this be possible if the router hat some secondary internal IPs for both WAN interfaces.
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
I have a working wired network and really all I want to do is set up my DIR-655 on it so that it provides internet only for wireless users, but doesn't allow access to the rest of the local network. I though that's what the Guest network would do, but when I connect to that I can still type in local IP addresses and get to those devices.
"Enable Routing Between Zones" is unchecked in the Guest Zone settings.
I'm trying to create a route-map for an EIGRP Distribute list on a N7K, the goal is to not advertise a 10.0.0.0/8 and 172.31.30.20/32 networks out a link to a remote site while permitting all other traffic to the internet (default). I configured the ACL/route-maps below and applied them outbound on the N7K interface but no subnets at all are being received on the remote site router.
ip access-list DENY_10.0.0.0 10 permit ip any 10.244.244.20/30 <<--WAN interface network 20 deny ip any 10.0.0.0/8 25 deny ip any 172.31.30.20/32 30 permit ip any any
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
I want to create a link between two homes about 10/15 miles away from each other. I was thinking about using microwave technology to achieve this. I would like to be able to use this connection for linking two home networks/internet and possibly running iptv and voip over the link. I was hoping to operate in the unlicensed frequency.
I have 2 internet services with separate ISPs. My local telephone exchange is somewhat dated so the maximum speed per ISP/connection is about 1 Gbps. I have streaming radio services, I do quite a bit of file downloading and there multiple devices currently trying to share a single connection. I haven't been able to utilise the second connection because my NAS and print serving is all configured on the first connection and therefore unavailable to users/services on the second connection.My goal is to utilise the available capacity of both connections but at the same time allowing all network resources (file and printer sharing, NAS drives, etc.) to be available jointly to all network clients.
My first router is a Netgear RangeMax ADSL modem/wireless router (DG834PN). This connects directly to one ISP and has the NAS and printers attached. The second router is a Netgear N600 wireless dual band router (WNDR3400) which attaches to a Linksys ADSL 2 Gateway with 4-port switch (AG241 v2) and then to the second ISP.As an aside, I also have a number of Devolo devices for utilising the electrical circuit for networking purposes. I have a dLAN 200 AVmini adapter connected to the RangeMax router with 2 further dLAN 200 AVmini adapters and a dLAN 200 AV wireless N adapter distributed through my house.
I recently purchased a HP PHOTOSMART D110 wireless/eprint all in one. I have the dir-615 router and cannot get the printer to show up on my home network.Printer works fine hard wired to pc but wireless not at all. The ip address of the printer is 169.254.147.xx while everything on my network is 192.168.0.xx. Printer says connected for a few seconds then disconnected....I have tried to configure it on a vista and a win 7 machine.Everything else shows up fine on my network, as a matter of fact a friend brought his laptop over and it connected great..
I have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
What device would be necessary to link two networks of identical type? What devices would be necessary to link two networks of dissimilar types?I would say a network card and HUB for identical type but I do not know if this is correct?Describe the parameters governing the choice of cable type for a given network. What are the three main types of cables used in computer networks?
I have a TP-Link TL-WR720N wireless router, and I am trying to set it up so that it limits the times that my kids can access the internet. I have included screenshots of all of the programming pages, so you can see exactly what I am looking at. Here is what I have done so far:
Schedule: I created several schedules for different days, weekdays, weekends, start at 1900, end at 2100, etc.
Host: I created a host name titled "All", and set it for 192.168.0.3 ~ 192.168.0.199. The router assigns from 192.168.0.2 thru 192.168.0.199. I assigned my computer's MAC address as the "Parent PC", and bound it to 192.168.0.2, through the "IP and MAC Binding" function. In this manner, I hope to limit the kids access, while allowing the parent PC to access it at any time.
Rules: I selected the option to "Allow" passing of packets during these hours. I then created rules, assigning the host "All" to the different schedules that I created. I set the target as any, and did not set up any targets in the target section, because I do not want to control what sites they visit (yet, anyway). I generally don't worry about the sites they visit, I just think they spend too much time on the internet.
Here is what happens. I use my laptop (not the parent PC) as a test machine. When trying to access the wireless, i have verified that the router does give me an IP address within the specified range I created in the schedule. If I set the Access Rule to "Allow" the packets to pass through the router, and try to connect during the time it is set for, it will not allow my laptop to even connect. The weird thing is, if I set it for "deny", I can connect, but I have no internet access. Either way, if I have any of the rules enabled, I cannot access the internet at all. Thinking maybe there was some sort of conflict with schedules, I tried enabling only one of the rules instead of all of them, with no change.
What am I doing wrong? Do I need to set targets? If so, does this mean I have to set one for every site I want them to be able to visit? Can I set a target as the IP address of the router? If so, what ports do I use?
I've been trying to set-up DMZ for my DSL-2542B-SE_1.00_06112008.
But the problem is when I access my IP from WAN, It connects to Router Control Panel, I have set DMZ IP as 192.168.1.2 which is the my computer where I have the Server set-up.
Now I've disabled DMZ but still I can access to my router from WAN through my IP.
i have a little network knowledge but the tp-link wa-500g is proving quite a challenge to set up.i am trying to set it up in client mode to use with the xbox 360.thhe problem is i seem to set everything up correctly but it doesnt actually seem to work or to connect to the main router..which is a sky sagemfast router...(could this maybe be the problem? and if so how could i sort this? i have set a static ip on the tp.link and set up in client mode and "supposedly" connected to the main router in which is hard to figure out if it has or hasnt...also my sky router has wpa security and i am wondering if something has to be configured in my tp-link wa-500g to connect? but i can find no information on this needing to be done.
I accidentally created a home network and want to remove it, as it blocks all my wireless devices.
I have a dir655 with 2.o firmware
Os on computer I set it up on is win 7 64 bit
How to make other wireless devices easily recognize it? when I try to access it the wireless computers ask me for code that I entered on setup that was printed on bottom of router but system doesn't recognize it.
I recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
I have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports) 2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports) 3. Test Bench AMD PC 4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
1. Green Packet DX-230 WiMAX modem with router 2. D-Link DIR-615 ver G2 (from my ISP) 3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address - The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address - The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
