Home Network :: How To Set Up Tp Link Wa500g As Client With Xbox 360
Aug 12, 2011
i have a little network knowledge but the tp-link wa-500g is proving quite a challenge to set up.i am trying to set it up in client mode to use with the xbox 360.thhe problem is i seem to set everything up correctly but it doesnt actually seem to work or to connect to the main router..which is a sky sagemfast router...(could this maybe be the problem? and if so how could i sort this? i have set a static ip on the tp.link and set up in client mode and "supposedly" connected to the main router in which is hard to figure out if it has or hasnt...also my sky router has wpa security and i am wondering if something has to be configured in my tp-link wa-500g to connect? but i can find no information on this needing to be done.
View 3 Replies
ADVERTISEMENT
Aug 21, 2011
I'm attempting to connect an Xbox 360 console to a Linksys WRT54GL router (wirelessly), using a TP-Link TL-WA500G wireless access point. I've had this working in the past, but I didn't make a note of the configuration unfortunately. The Internet connection is connected to the router. The device hasn't been used for several months. During this time, I installed Tomato firmware onto the WRT54GL router, however I have since completely restored the router to factory defaults, by reinstalling the default firmware and performing a hard reset. Having reset the device, I was surprised to see that the Tomato favicon is still displayed when accessing the router's admin webapp.
View 1 Replies
View Related
Feb 28, 2011
I'm trying to connect a non-wireless enabled pc to my virginmedia network by using a tp-link ta-wa500g router in client mode. The pc connects to the router via ethernet fine, and i can access the router admin page etc., but the router doesn't seem talk wirelessly to the virgin box. it finds it and everything, but i can't access the internet at all. i've tried removing the password, resetting everything, I've upgraded to the latest firmware, but have come to a bit of a dead end.
View 1 Replies
View Related
Mar 25, 2011
I have a Tp-link wa500g and it won't send Internet across the network, ive recently bought it and I want to connect it to a segam router (sky issues). I've tried putting it in all connection modes but none work. It wont even connect me to the Network. I'm trying to use it as a repeater to extend my network throughout my house without cables
View 2 Replies
View Related
Dec 31, 2011
My setup consists of the following: TP-LINK Router Model No. TL-WR541G and TP-LINK Wireless Repeater Model No. TL-WA500G.I've set the Wireless Mode Settings to Universal Repeater and turned on MAC filtering. My problem is that when I connect to the wireless repeater with a phone or tablet (both working on android) it just wont connect. It gets stuck on "obtaining ip address". The wireless repeater works fine with any laptop, pc, netbook etc. I made sure that all the MAC Addresses are entered correctly. Also the phone and tablet connect fine to the router, but when the router is out of range and it tries to connect to the repeater it doesnt work. I tried all the basic troubleshooting techniques i.e. turning off wifi, turning off repeater & router.
View 6 Replies
View Related
Jul 14, 2011
My PC is wireless connected to my modem, My X-Box is wired to my modem, PC detects x-box in home network, X-Box doesn't see PC when running connection test, X-Box however does connect to web. When I plug in an Ethernet Cable from my Modem to my PC the X-Box instantly detects my PC. I can't figure out how to make my x-box communicate with my PC when it's it's half wireless / half wired.
View 1 Replies
View Related
Jan 21, 2012
recently I've connected to my OpenVPN and everything works fine on my PC I'm getting okay speeds and the VPN IP appears on [URL]The problem is I wanna use internet connection sharing to play Xbox Live while connected through my VPN and I'm having issues.My Xbox isn't even recognizing my wired connection.This is the setup:Wireless Connection > Desktop > OpenVPN > Wired connection from desktop to XboxWhat I think I'm doing wrong is not specifying the correct home networking connection for my LAN 3 (Tap-Win32 Adapter OAS)I tried sharing the LAN 3 connection and set the home networking connection to my Wireless and it disconnects me from my wireless network.
View 1 Replies
View Related
Nov 29, 2007
I have a xbox 360 that I want to connect to xbox live with, using my home network. Every time I try to connect to xbox live the only part that fails is the connecting to xbox live part. This is how my network is set up. I have Cox Cable as my ISP, a Linksys WCG200 gateway(v2), and WRT54GS(v7). The cable wire is connected to the WCG200 gateway, then an Ethernet cable connects the gateway to the WRT54GS router, and finally an Ethernet cable connects the router to my xbox 360. I have contacted Cox, Linksys, and Microsoft about the situation and they all say the problem is the version of the router. Someone told me that I may just need to change the firmware, but I don't know how to do that.
View 9 Replies
View Related
Nov 15, 2012
Ive been trying to work this out on XBL forum for a while. all my settings seem to be correct ( UPnP, NAT type: open, no port forwarding or triggering, IP settings on Xbox's are auto).
The two Xbox can play online separately, when either one of them attempts to join the others party it disconnects from Xbox live.
According to the microsoft website, Xbox live only supports the Hardware version 1A and Firmware: 1.00NA.
My router has B1 and 2.00NA. is there a way to downgrade?
View 4 Replies
View Related
Sep 24, 2012
I've installed Fortigate 60B and now need to provide access to our guests. Guests must be isolated from office infrastructure. For this configuration I've set up DMZ interface with DHCP server. Client connected to DMZ port gets DHCP configuration but can't go out to the Internet.
Internal interface:
Addressing mode: manual (10.0.0.250/24)
DMZ interface config:
Addressing mode: manual (192.168.16.1/24)
[Code].....
View 5 Replies
View Related
Jan 29, 2011
I just upgraded my wireless router to a D-Link DIR-655. I have 2 PCs and a network storage device (D-Link DNS 321) connected via ethernet to the router. I also have an xBox 360 connected wirelessly to the router. The xBox is able to connect to the internet via the router, but it cannot connect to (see) the PC's or the network storage device. It was able to do so with my old wireless router (a Belkin), but it stopped with the DIR-655.
View 4 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Nov 11, 2011
i was able to network my window xp pcs with easy. I control my cyber cafe with handy cafe and it wporks on my xp pc using a switch.(Dlink) My challenge is now how to network window 7 OS pcs that are directly connected to a wireless router for internet. All the systems browse wirelessly via the router but i can't share filesMy major problem is our to use handy cafe to control the systems(15pcs)
View 3 Replies
View Related
Jul 5, 2012
I use vmware workstation, and doing small networking project.i use 1 windows server 2008 x64 sp1 as DC, DNS and DHCP with 2 nic(1 nic for local(vmnet2) and 1 for internet(NAT)) and i use 1 windows 7 client machine.in server local nic settings are ip 200.200.200.1 sm 255.255.255.0 gw: empty dns 200.200.200.1
and internet nic settings all set automatic.and in DNS i added forwarder as my company's actual DNS server name.My requirement is client should browse internet by resolving through my dns server.but the problem is my server is having internet but my client windows 7 does not have internet
View 6 Replies
View Related
Jun 21, 2012
is it possible for a client to choose a WAN to use when being routed through a Multi-WAN router? Something that could be configured as default route in linux or default gateway in winxp ?Or is this decision totally up to the router itself ? [code] Could now a client on the subnet 192.168.0.0/24 choose 1.1.1.1 as a default route for example? And if not, could this be possible if the router hat some secondary internal IPs for both WAN interfaces.
View 3 Replies
View Related
Dec 11, 2012
i use cisco vpn client software to connect my laptop to my company's network when i at home. using dsl modem.
i wonder if it is technically possible to connect my local printer to dsl router and in such a way establish connection between my laptop and printer?
View 5 Replies
View Related
Nov 27, 2012
is it possible to setup 3 x xbox 360's in a home network, 1 is mine, connected to live, the other 2 are for the kids but i just want to setup local network gaming with the kids but also so they cannot connect to live account as they still young. i'm looking to run game on mine and stream / share a multiplayer game with the kids but restrict their internet access?
View 2 Replies
View Related
Apr 7, 2011
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
View 1 Replies
View Related
Jan 23, 2013
Region : Italy
Model : TL-WR702N
Hardware Version : Not Clear
Firmware Version :
Android Tablets do not connect to Wifi Ad Hoc network (IBSS).My Nokia phone create an HotSpot WiFi network type AD HOC (IBSS).With TL-WR702N in Bridge or Repeter i connect it to Nokia Phone in "Ad Hoc" mode and creare an AP Wifi infrastructure network that my Android Tablet can connect to it.
View 3 Replies
View Related
Sep 25, 2011
I want to create a link between two homes about 10/15 miles away from each other. I was thinking about using microwave technology to achieve this. I would like to be able to use this connection for linking two home networks/internet and possibly running iptv and voip over the link. I was hoping to operate in the unlicensed frequency.
View 2 Replies
View Related
Jul 3, 2011
I have 2 internet services with separate ISPs. My local telephone exchange is somewhat dated so the maximum speed per ISP/connection is about 1 Gbps. I have streaming radio services, I do quite a bit of file downloading and there multiple devices currently trying to share a single connection. I haven't been able to utilise the second connection because my NAS and print serving is all configured on the first connection and therefore unavailable to users/services on the second connection.My goal is to utilise the available capacity of both connections but at the same time allowing all network resources (file and printer sharing, NAS drives, etc.) to be available jointly to all network clients.
My first router is a Netgear RangeMax ADSL modem/wireless router (DG834PN). This connects directly to one ISP and has the NAS and printers attached. The second router is a Netgear N600 wireless dual band router (WNDR3400) which attaches to a Linksys ADSL 2 Gateway with 4-port switch (AG241 v2) and then to the second ISP.As an aside, I also have a number of Devolo devices for utilising the electrical circuit for networking purposes. I have a dLAN 200 AVmini adapter connected to the RangeMax router with 2 further dLAN 200 AVmini adapters and a dLAN 200 AV wireless N adapter distributed through my house.
View 2 Replies
View Related
Mar 3, 2011
I recently purchased a HP PHOTOSMART D110 wireless/eprint all in one. I have the dir-615 router and cannot get the printer to show up on my home network.Printer works fine hard wired to pc but wireless not at all. The ip address of the printer is 169.254.147.xx while everything on my network is 192.168.0.xx. Printer says connected for a few seconds then disconnected....I have tried to configure it on a vista and a win 7 machine.Everything else shows up fine on my network, as a matter of fact a friend brought his laptop over and it connected great..
View 14 Replies
View Related
Feb 4, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I have an unused TD-W8151N. I also have a smart TV that requires a wired connection, with no way of getting a wire to it.
Can I configure my spare TD-W8151N as a client of the existing WiFi network and connect the TV in to the TD-W8151N with a cable?
View 2 Replies
View Related
Jul 23, 2011
I have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
View 13 Replies
View Related
Nov 20, 2011
What device would be necessary to link two networks of identical type? What devices would be necessary to link two networks of dissimilar types?I would say a network card and HUB for identical type but I do not know if this is correct?Describe the parameters governing the choice of cable type for a given network. What are the three main types of cables used in computer networks?
View 3 Replies
View Related
Jan 8, 2013
I have a TP-Link TL-WR720N wireless router, and I am trying to set it up so that it limits the times that my kids can access the internet. I have included screenshots of all of the programming pages, so you can see exactly what I am looking at. Here is what I have done so far:
Schedule: I created several schedules for different days, weekdays, weekends, start at 1900, end at 2100, etc.
Host: I created a host name titled "All", and set it for 192.168.0.3 ~ 192.168.0.199. The router assigns from 192.168.0.2 thru 192.168.0.199. I assigned my computer's MAC address as the "Parent PC", and bound it to 192.168.0.2, through the "IP and MAC Binding" function. In this manner, I hope to limit the kids access, while allowing the parent PC to access it at any time.
Rules: I selected the option to "Allow" passing of packets during these hours. I then created rules, assigning the host "All" to the different schedules that I created. I set the target as any, and did not set up any targets in the target section, because I do not want to control what sites they visit (yet, anyway). I generally don't worry about the sites they visit, I just think they spend too much time on the internet.
Here is what happens. I use my laptop (not the parent PC) as a test machine. When trying to access the wireless, i have verified that the router does give me an IP address within the specified range I created in the schedule. If I set the Access Rule to "Allow" the packets to pass through the router, and try to connect during the time it is set for, it will not allow my laptop to even connect. The weird thing is, if I set it for "deny", I can connect, but I have no internet access. Either way, if I have any of the rules enabled, I cannot access the internet at all. Thinking maybe there was some sort of conflict with schedules, I tried enabling only one of the rules instead of all of them, with no change.
What am I doing wrong? Do I need to set targets? If so, does this mean I have to set one for every site I want them to be able to visit? Can I set a target as the IP address of the router? If so, what ports do I use?
View 1 Replies
View Related
Feb 23, 2011
I've been trying to set-up DMZ for my DSL-2542B-SE_1.00_06112008.
But the problem is when I access my IP from WAN, It connects to Router Control Panel, I have set DMZ IP as 192.168.1.2 which is the my computer where I have the Server set-up.
Now I've disabled DMZ but still I can access to my router from WAN through my IP.
View 2 Replies
View Related
Jan 25, 2012
I accidentally created a home network and want to remove it, as it blocks all my wireless devices.
I have a dir655 with 2.o firmware
Os on computer I set it up on is win 7 64 bit
How to make other wireless devices easily recognize it? when I try to access it the wireless computers ask me for code that I entered on setup that was printed on bottom of router but system doesn't recognize it.
View 1 Replies
View Related
Jun 19, 2011
I recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
View 3 Replies
View Related
Dec 4, 2012
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies
View Related
Mar 22, 2011
I have the above router on 10.10.10.1 which I'm quite familiar with but I need reaching a VM residing on one of my internal MAC's. My cisco route table is as follows:
Gateway of last resort is 93.97.20.1 to network 0.0.0.0
93.0.0.0/21 is subnetted, 1 subnets
C 93.97.16.0 is directly connected, ATM0.1
10.0.0.0/24 is subnetted, 1 subnets
C 10.10.10.0 is directly connected, BVI1
S* 0.0.0.0/0 [1/0] via 93.97.20.1
The internal physical machine that contains the VM is 10.10.10.9 whose routing table is:
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 10.10.10.1 UGSc 6 8 en0
10.10.10/24 link#4 UCS 5 0 en0
10.10.10.1 0:1b:2b:cc:7:8a UHLWI 7 1248 en0 284
10.10.10.9 127.0.0.1 UHS 0 86171 lo0
10.10.10.11 0:23:54:2a:6:d3 UHLWI 0 234 en0 150
10.10.10.30 0:9:34:28:60:2e UHLWI 0 25 en0 857
10.10.10.111 0:1d:ec:2:2d:2d UHLWI 1 1599 en0 721
10.10.10.255 link#4 UHLWbI 2 18609 en0
10.37.129/24 link#8 UC 2 0 vnic1
10.37.129.2 0:1c:42:0:0:9 UHLWI 1 2 lo0
10.37.129.255 link#8 UHLWbI 2 14046 vnic1
10.211.55/24 link#7 UC 2 0 vnic0
10.211.55.2 0:1c:42:0:0:8 UHLWI 0 2 lo0
10.211.55.255 link#7 UHLWbI 2 14046 vnic0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 5 214223 lo0
169.254 link#4 UCS 0 0 en0
The VM has a static IP of 10.211.55.5 and can obviously ping out to the rest of my lan but as of yet my router and other machines on the 10.10.10/24 subnet cannot reach the VM. I sort of presume this is a simple task of adding some kind of static route on my router and then all other machine will know how to get to the VM. So what do I need to do as I have about 40 or so customers already connected of whom I do not wish to suddenly halt their access due to my inexperienced attempts to create this route or new link(s)
View 1 Replies
View Related
Mar 28, 2012
I have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
View 1 Replies
View Related
Jul 21, 2011
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
View 2 Replies
View Related
