Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I have an unused TD-W8151N. I also have a smart TV that requires a wired connection, with no way of getting a wire to it.
Can I configure my spare TD-W8151N as a client of the existing WiFi network and connect the TV in to the TD-W8151N with a cable?
Region : India
Model : TD-W8151N
Hardware Version : V3
Firmware Version : 120530
ISP : BSNL
Net is working smoothly from LAN, but no success on wifi. Over wi-fi, I can connect to router but cannot access net.
Region : Vietnam
Model : TD-W8151N
Hardware Version : V1
Firmware Version :
ISP :
I'm using a Tp-Link's Product (TD-W8151N). But now, i want to using TL-Wr740N repeat the Wifi from TD-W8151N. How can i do that?
Region : Indonesia
Model : TD-W8151N
Hardware Version : V3
Firmware Version :
ISP :
Recently I bought TD-W8151N wireless adsl router, I have one desktop computer that connected to TD-W8151N via ethernet and wirelessly to one laptop, IP Addr: 192.168.1.4, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : desktop (LAN connection IP Addr: 192.168.1.3, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : laptop (wireless connection) but I can't ping each other and also can't access the share folders between them., both computers can access internet. Is there anything I missed the configuration setting of the router? Before I use wireless, I connected this 2 computers using cross-type utp cable, and working good.
Region : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment. But I don't see any way to configure the device to join an existing wireless network. Am I wasting my time?
View 7 Replies View RelatedRegion : Italy
Model : TL-WR702N
Hardware Version : Not Clear
Firmware Version :
Android Tablets do not connect to Wifi Ad Hoc network (IBSS).My Nokia phone create an HotSpot WiFi network type AD HOC (IBSS).With TL-WR702N in Bridge or Repeter i connect it to Nokia Phone in "Ad Hoc" mode and creare an AP Wifi infrastructure network that my Android Tablet can connect to it.
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
Region : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
Find list of all the MAC address of the devices connected to the router?
View 2 Replies View RelatedModel : TD-W8951ND
Hardware Version : V3
Firmware Version :
ISP : BSNL DATAONE
my tablet show wifi status connected ... signal quality... but cant access internet ...
Region : UnitedStates
Model : TD-W8968
Hardware Version : Not Clear
Firmware Version : eranet
ISP : eranet
I don't know how to set my mobilephone wifi.It's made by HUAWEI.Then it cost me a lot.Who can tell me how to set it?
Region : India
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 4.0
ISP : BSNL
i have bought TP-Link W895IND and frequently the WIFI is not working. Everytime i have to active and deactive. Now since last one day it totaly stoped working . WIFE icon is glowing continously without flickering.
I need to know what to look at to get wi-fi connection to my existing linksys wrt54gs2 v1 network
View 1 Replies View RelatedRegion : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
Region : Canada
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 120608
ISP : Distributel
I've just installed this router today, connected physically 2 PCs, a PS3 and a VoIP and everything works fine !
The problem is with the WIFI connection ! my devices see the WIFI network, they connect, but I cannot connect to the internet ...
What settings Should I turn on/off or any config I should tweak ?
Region : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : talk talk
All working well except Net Radio on my Yamaha AV amp. When attempting to listen message receive 'access error' never had this with Linksys router. The amp has been setup with the internal lan gateway address and used dns from talk talk detail. IP has a static IP address . I have tried placing amp in dmz address which didn't work also tried port forwarding 8000 - 8001 which someone said was the port used for yam net radio. none of this works. Never had to do any of this before simply used local gateway address and local internal dns from the old router and always worked with tp - link just cannot get it to go.
Tried lots of variation gateway and dns addresses none which worked...
Region : Vietnam
Model : TD-W8101G
Hardware Version : V3
Firmware Version :
ISP :
I have a TP-Link modem/wireless routerTD-W8101G, from the internet provider. The wireless function has been switched off.
An Apple Airport Extreme router is connected to this modem to provide the network.
I have a spare TP-Link TD-WR740N modem/wireless router. Can I configure this as a network extender?
Region : India
Model : TD-W8901G
Hardware Version : V6
Firmware Version : 6.0.0 Build 120418 Rel.34102
ISP :
Everytime, I turn on the ADSL2+ wireless modem router, it connects to the internet and my laptop gets paired with the wireless network but after 30 mins time, wireless ADSL2+ router restarts itself and goins in a loop for nearly 5 times and then it gets connected to internet but then I cannot connect my laptop to the the router using wireless with error DHCP failed to assign IP but DHCP is enabled in the router. This has started since a month and I had tried several network change settings but nothing has given me a solution. I do use Kaspersky IS through which the connection flows in. My internet setting is set to use Automatic DNS discovery and most time, I get RC 102 DHCP error.
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies View RelatedRegion : India
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.13.27 Build 121101 Rel.38183n
I have bought TP-Link TL-WR841N 300 mbps router. I have 20-25 wireless clients but only 15 wireless clients are able to connect to the router. Is there the limitation on numbers of wireless clients can connect to the router?
Region : Poland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I have some linksys router that I used as wireless client bridge. I have main router that is connected to Internet and linksys router which is connected to main router's WiFi. Linksys router acts as client bridge connecting LAN devices to main router. Now I own TL-WDR3600 and I would like to replace linksys router. How can I achieve the same on TP-Link router? I don't see any option for setting wireless operation mode.
A dlink 615 router so im trying to set up a new network. So downstairs i have a netgear g router, this is then hardwired to a switch, from there i have another cable running upstairs and into my d link router.I am using snow Leopard OS, and using VMWare was able to use the quick setup on the associated disc but could only reach the stage where i connect my ethernet to router before it would display an error message stating it was unable to find a router.I then tried manually setting up the router online using
192.168.0.1
but was unable to get a working connection running over the wireless and i was only able to give this page when hardwired to the d link router.
how to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.
View 1 Replies View RelatedNetwork set up; wireless router (D-link DIR825) to Cisco switch (SD208p) and have Wap200 hooked to cisco switch to extend range up one floor. Can see it as wireless network, but cannot configure it with web browser. Address 192.168.1.245 just times out via pings as well. Have done all resets, power on reset, etc nothing.
View 3 Replies View RelatedRegion : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
I had a Airtel connection with me for which i was provided Beetel 450 BXI ADSL2 + Router to connect to net using wi-fi on my laptop.How ever now i have changed my isp to ortel cable net providers.i access net on my laptop using lan cable connected from cable modem to my laptophow to configure Beetel 450 BXI ADSL2 + Router so that i connect my cable modem to Beetel 450 BXI ADSL2 + Router and access net wi-fi on my laptop. my os is vista.
View 1 Replies View RelatedRegion : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
cofigure a ADSL2+ Conexion in an 1941 router.line protocol are up but didn't have ip adresse in my interface.[code] i don't know how i can find the probleme, and debug's comandes no show me anything.
View 3 Replies View RelatedOur Motel has a new CenturyLink DSL Wifi Modem at the office desk, and I'm trying to get wifi to all customers via (3) Linksys WRT110 wfi routers that are in the attic. How do you configure the routers so all put a wifi signal out with the same network name ? I keep getting limited connections & etc...
View 1 Replies View Related
