TP-Link ADSL2+ Wireless :: TD-W8151N - Can't Connect Between Wired LAN And Laptop Wirelessly
Mar 29, 2013
Region : Indonesia
Model : TD-W8151N
Hardware Version : V3
Firmware Version :
ISP :
Recently I bought TD-W8151N wireless adsl router, I have one desktop computer that connected to TD-W8151N via ethernet and wirelessly to one laptop, IP Addr: 192.168.1.4, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : desktop (LAN connection IP Addr: 192.168.1.3, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : laptop (wireless connection) but I can't ping each other and also can't access the share folders between them., both computers can access internet. Is there anything I missed the configuration setting of the router? Before I use wireless, I connected this 2 computers using cross-type utp cable, and working good.
Region : India Model : TD-W8901G Hardware Version : V6 Firmware Version : 6.0.0 Build 120418 Rel.34102 ISP :
Everytime, I turn on the ADSL2+ wireless modem router, it connects to the internet and my laptop gets paired with the wireless network but after 30 mins time, wireless ADSL2+ router restarts itself and goins in a loop for nearly 5 times and then it gets connected to internet but then I cannot connect my laptop to the the router using wireless with error DHCP failed to assign IP but DHCP is enabled in the router. This has started since a month and I had tried several network change settings but nothing has given me a solution. I do use Kaspersky IS through which the connection flows in. My internet setting is set to use Automatic DNS discovery and most time, I get RC 102 DHCP error.
I'm currently using an orange livebox which has been pretty reliable in the past. My set up is livebox > homeplug > homeplug > linksys wireless router > into 2 pcs.Its odd because my pcs have trouble detecting the wireless router, however my laptop can link up no problems.I have plugged my laptop directly into the livebox via ethernet and it works fine so I can rule out the livebox. I've also swapped the cables and they all work ok.Basically, it does link up intermittently and runs perfectly, but then after a day, or even 10 minutes it disconnects and I have a nightmare getting it to work again. I went through the entire cable system and got right to the end and hey presto it all worked...so I plugged my pcs back in. Then after about 10 mins it lost the network connection and I couldnt even link up to the livebox router by keying in 192.168.1.1. The laptop CAN connect wirelessy and access the config pages.
Region : UnitedStates Model : TD-W8960N Hardware Version : V3 Firmware Version : ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
I have a linksys WRT54GH wireless router running firmware v1.0.01 build 001.It's setup with DHCP.My desktop computer is connected to the router via cable.I also access the connection using my laptop, via wireless.The problem is that after I start using the desktop (wired connection), I can't connect from the laptop using wireless. It happens every time. I then turn the router off and back on again. After this procedure I can successfully connect from both the desktop (wired) and laptop (wireless).
A couple nights ago, my wireless router (Linksys BEFW11S4 ver4) just stopped letting me connect to the internet. All the lights were still flashing as they should, I could still go to the setup page, I just could not connect to the internet, both through wired and wireless. I could connect straight through the modem though.
So I decided that since the router was probably over a decade old that maybe it was just its time, and I bought a new one (E1000). I connected it, and still could not connect to the internet. I then did some internet searching and found this [URL] and I followed what was mentioned in post 10 (MAC address clone and changing local IP). Now I can connect through the wired connection and I rejoiced thinking I solved it.
Then I checked my laptop and it won't even connect to the router. It sees the router, but when I ask it to connect, it just says it can't. I decided I was too exhausted to try searching and fixing it on my own and if I tried I'd just end up breaking something out of frustration.
My friend's wireless internet just suddenly failed last night. She was watching Youtube videos, but had to do something, so she closed the window. When she came back, she couldn't connect, and was given an error, something about user connectivity.Her wired connection is still working.
Region : Italy Model : TD-W8970 Hardware Version : V1 Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
I'm connected to a wifi at home on my cellphone, says signal status is excellent, 54mbps, wpa psk security but I cannot connect to the network. My desktop pc is connected via ethernet and it is working. I tried connecting to a neighbor's wifi and it worked on the same cellphone. WLAN light is flashing, the rest are solid. I have a prolink adsl router.
Model : TD-W8951ND Hardware Version : Not Clear Firmware Version : ISP : Metronet BPL
I connect to the internet by BPL modem on electricity , for using my modem's wireless feature ı have to close DHCP and use modem in bridge mode, otherwise I can't use wireless, And my problem is connecting to the internet with my LG 42LM640S smart tv using wireless, When I talk with LG techinal service they came and try to connect tv to the internet with using their android phone's hotspot feature, my tv connect with phone's hotspot feature to the internet,So they said that "you have to change tp link modem's encoding system?Now it's encoding mode in WPA enconding system :S But whwen ı shut down encoding wireless tv didn't connect again?
Region : Others Model : TD-W8961ND Hardware Version : V2 Firmware Version : 2.0.0 Build 120427 Rel.09135 ISP : True
I just bought the wireless router as stated in the subject and I cant get 2 of our PC�s to connect wirelessly for some reason. 4 other PC's are fineAll machines running windows 7, but when the authentication type on WPA2-PSK the 2 computers ask for a password which we put in but keeps saying its wrong, but infact its right.I can connect them on WPA-PSK, but then all the computers drop out after 30 seconds.
Region : UnitedStates Model : TD-W8961ND Hardware Version : V2 Firmware Version : ISP : ATT
I want to add more users to my home network and I couldn't, at this moment I only can connect 8 devices (12 devices at least) when I try to connect the next one its impossible, but if I take off one of the connected devices then the router allows to connect the new one.How can I connect more than 8 devices to my router ? (wireless)Also, is there any limits with Wireless MAC Address Filter ? because I can't add more than 8 MAC addresses in my old router I could do that.
Region : India Model : TD-W8968 Hardware Version : V1 Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n ISP : BSNL
I Bought thisTD-W8968 a month back.. It was working alright till a few days back. From the past 3days i'm experiencing internet light and DSL light going off...The DSL light is not constant even for 5min...When the DSL light comes up, the internet light takes almost 5min to comeup or before internet light come up the DSL light goes off.There wasn't problem with my old UT star modem..I already checked,its running fine without disconnection..When i replace it with TD-W8968 router ,the problem continues.. When my internet connection was good...The SNR margin was like 25 for upstream and 31 for downstream...After 2 days it went mad. here are the images shows about current reading..Fluctuates between 0.2 - 100 upstream and 2-35 for downstream
I have a network that starts with a Linksys wireless router (DSL connected here) then it goes to a Netgear switch (computers connected here) and then a Netgear wireless router for an iMAC to connect to. I can't see the last router or the iMAC on my Win 7 machine? when I map network I get an error message about an incompatible device.
i want to simply see my desktop on my tv without cables is this possible without using apple tv or push2tv or whatever else that is out there like that, i have a wireless router a laptop with wifi and a a tv which can connect to both wirelessly, i have no problem sharing files, vids photos etc but how can i browse net on laptop on couch but can see it through my tv.
It will work when I connect it using an ethernet cable but it won't connect to the wireless.When I run the network diagnostics, it says The wireless network key does not match or something like that
I have a LG tv with wifi and want to connect rto my Dell lap top (o/s 7)the tv sees the laptop recongnise's its name but when asked to conect comes up with "unknown error"message the laptop shows nothing
Region : Ireland Model : TD-W8960N Hardware Version : V4 Firmware Version : TD-W8960N ISP : Vodafone Ireland
I am having a rather annoying problem. I run a small hotel (just 3 floors) and my modem gives a strong enough signal to provide wireless access to everybody in the house however I'm finding that a lot of people, whilst they can connect to the modem, cannot browse online. Connection just times out when they open their browsers.Recently a guest gave me his laptop and asked me if I could do anything with it. I'm by no means an expert when it comes to this kind of thing so I chanced my arm by putting his MAC address into the CP's Wireless/MAC Filter page. He connected immediately and was able to go online much to my relief.
Thing is, I don't want to have to do this for every guest that comes through my door! Is there any way everybody who has a laptop can connect without me manually entering their MAC addresses? MAC restrict mode is set to 'disabled' but I thought that would allow everybody unrestricted access?
Region : UnitedStates Model : TL-WR1043ND Hardware Version : V1 Firmwar Version : ISP : AT&T
I recently got a new modem from AT&T. I hooked it up and everything worked fine for a few days. Last night some friends came over with their wireless devices (iphone, ipad) and after a while, the internet got really slow. Then it was unresponsive but it said that we were still connected to the network. So I decided to restart the router. Once it was finished rebooting, we were not even able to connect to the network at all. Even on my computer downstairs I was not able to connect wirelessly. I am connected via ethernet from the router right now on my computer upstairs and that is working fine. I have tried rebooting the router to factory settings, unplugging the modem, rebooting the modem, unplugging the modem, changing the router settings, pretty much every practical solution for simple connectivity issues.
I received a new hard drive along with recovery discs from dell yesterday. They told me the new drive would be blank and I would have to run the discs. Not a problem. Installed the OS along with the drivers that had check marks next to them.
Today I plug in my home internet and it won't work. Unplug it and turn the wireless back on and it gets online just fine.
I'm having a big problem with my connectivity. I can connect to the internet (a BT Home Hub router) using my ethernet cable but not using wireless. My computer is searching and finding wireless networks, but when I try to connect to my router, it says limited access/connectivity.
I haven't used my computer in quite a long time (7 months) as it stopped working and is miraculously working again now (huzzah!) but the wireless does not, when it was perfect previously.
I have run IPCONFIG/ALL and the details are below. This is done with the ethernet cable attached.
---------------- Windows IP Configuration Host Name . . . . . . . . . . . . : Primary Dns Suffix . . . . . . . :
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
recently tried to connect a Samsung BD-EM57C blu-ray player to my wireless network. I have a D-Link WBR-1310. Have one desktop, Smart tv currently on network --no problems. Blu ray will find my network but cannot connect. "unable to connect enter ip address manually" which I did. Fail. "enter subnet mask" which I did. Fail. "Ip address taken enter different address" Now what?
I just got a TL- WR740N router and somehow managed to configure it using my girlfriends Acer Aspire One Happy netbook.The internet works fine when the netbook is connected to the router via cable but it can't connect wirelessly to the network I have created. At first some massege appeared saying that there are 2 identical IP's and there is a conflict or something like that. Now it just stops trying to connect to the network. I can connect with my own laptop tho.
