Region : Hongkong Model : TL-WR702N Hardware Version : V1 Firmware Version : ISP :
Before my TL-WR702N was working fine as a reperter. After sometime it doesn't work any more, so I try to reset it again but now I couldn't see my SSID after I press the survey buttom in the quick setup - wireless repater page.
Region : UnitedKingdom Model : TL-WR740N Hardware Version : V4.23 Firmware Version : TL-WR740N_V4_130104 ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
Region : Indonesia Model : TD-W8151N Hardware Version : V3 Firmware Version : ISP :
Recently I bought TD-W8151N wireless adsl router, I have one desktop computer that connected to TD-W8151N via ethernet and wirelessly to one laptop, IP Addr: 192.168.1.4, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : desktop (LAN connection IP Addr: 192.168.1.3, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : laptop (wireless connection) but I can't ping each other and also can't access the share folders between them., both computers can access internet. Is there anything I missed the configuration setting of the router? Before I use wireless, I connected this 2 computers using cross-type utp cable, and working good.
i had the dir-655 with desktops and laptops running with xp and win 7, also some other devices such as ipod, iphone, ps3, xbox, problem occura with conflict of network ip address, i think xp and win 7 both login with the same network ip address. So I start to disconnect every device and try to connect each desktop and laptops, one by one, enabled the DHCP and reserve the network ip to avoid conflict. But here's the problem, when I connect the first computer with wired to the dir-655, can't find the computer in the DHCP list so I cannot do the reserve, I'm able to surf internet even I can see info with ipconfig. So I connected 1 wired and 2 wifi to the network, only 1 wifi network ip showing on the list, so I reserve that one, but after I refresh, the DHCP list is empty.
My boss would like to know if there is a way to find out the ip address of a person VPN ing into our network. Let's say Joe Smith is VPNed in from home and his carrier is cox communications. How would I go about finding out what his ip address (the ip issued to him by cox) is? Is that even possible? If it is possible, is there a way to create a list of ip addresses of everyone that has ever VPN ed into our network? We are using a Cisco ASA 5520 and Cisco VPN Client.
Region : UnitedStates Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.1 ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : India Model : TL-WR740N Hardware Version : Not Clear ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
I need to know the maximum number of MAC addresses that can be entered in to the MAC security filter list on the AP541N.I know it has a maximum number of 200 concurrent users, however the documentation does not specifiy whether this also applies to the MAC filter.
I have used wireless acces points in the past that allow hundreds of users but only allow 64 MAC addresses, so this is very important.
I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
Region : UnitedKingdom Model : TL-WR740N Hardware Version : V3 Firmware Version : not sure ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
Region : Argentina Model : TL-WR741ND Hardware Version : Not Clear Firmware Version : 3.12.4 Build 100910 Rel.57694n
I did a hard reset and after that, when i power on the router, it works for aprox. 15 seconds, so i can access the interface at 192.168.1.1, but after those 15 seconds it doesnt respond. The lights are on as if it was perfect, but cant go on admins interface and ping doesnt work either. I did several resets, did the 30/30/30, and clicked on reset to factory defaults on those 15 seconds but nothing happens.
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : Australia Model : TL-WR702N Hardware Version : V1 Firmware Version : ISP :
I am posting this in the wrong place but thats only because I cant find the forum for the TL-WR642G ver 3.6 device.Basically I am unable to see any QOS configuration and I wanted to know if this is available to this model ?I know the ver 4.0 firmware update states that QOS is added but can I update a 3.6 device using a ver 4.0 firmware ?
Region : China Model : TL-WR741N Hardware Version : V4.20.0 Firmware Version : ISP :
I am American living in China. My Chinese reading is not so good, I am still learning. The interface for my router comes up in Chinese. Is there a way to change the language to English? So far, all I can do is get the set-up interface through IE, but I can not set it up!
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.
Region : Bangladesh Model : TL-WR720N Hardware Version : V1 Firmware Version : ISP : Is pros
After i bought the router it was working perfectly. But after using 1 week it freezes now and then. Happens around 10-30 times a day. The one or two led lights stops flashing and no device can connect to the router or asses internet. Another issue is that sometimes i cant connect any device through wifi (tried with android phone and ipod) and and but works perfectly on my pc. If i restart my router is works perfectly but after 1 min-3 hours sames problem happens either router freezes or cant connect though wifi
Region : Canada Model : TL-WR700N Hardware Version : V1 Firmware Version : latest ISP : Cogeco
I have a WR700N set up in bridge mode so as to provide a wifi signal in far end of our home. I used Bridge so we can tell which router we are connecting to. So we have two SSIDs (MySSID1 and MySSID2) Both with secure log-in. This works fine for about a day, and then disconnects. I then have to mess with the WR700N by plugging it in and out, maybe logging into it and changing something. Then it will work again - for a day
I updated the firmware with no change. Main router is a Dlink 615 with IP of 192.168.0.1. connected to cable modem. TP-LINK is set at default of 192.168.0.254 and gets a wireless signal from dlink.In an attempt to improve situation, I now have both units set to channel 11 and with fixed 20Mhz channel width. b/g/n on TP and g/n on dlink.
Region : Philippines Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version : ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
Region : UnitedStates Model : TL-WR720N Hardware Version : V1 Firmware Version : ISP :
Just bought a new TP-Link TL-WR720N router. Hooked it up and got internet access just fine. However, when I go to [URL] or http://126.96.36.199 to try and login to setup the router, I just get the standard message:
Username or Password is incorrect. Please refer to the troubleshooting below:
Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". Note: The settings will be restored to factory default after the resetting.How to restore the device to the factory default settings? Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings. I am using a Cat 5e ethernet cable, I don't have NOD32 or any other antivirus or firewall blocking access, I even changed the settings and disabled IPv6 via ethernet since that was also suggested in the FAQ, but I still don't get a login screen.
I reset the router, rebooted my computer, unplugged the modem/router, reset everything again, double checked the IP address and pinged the router with excellent results, but nothing makes it so the login screen appears.I then hooked up the router to a PC running Windows XP with Internet Explorer 8 and the login screen works fine like you would expect. Went in, adjusted settings, everything works ok. This router is very new, it should support Windows 7 and Internet Explorer 9, shouldn't it? I don't want to have to keep old computers around just to login and change settings on my router.There must be some default setting in Windows 7 or in IE9 that causes this issue with the TL-WR720N router. I've tried everything that seems to cause the same issue on other routers, both TP-Link and other brands, and none of those seem to be what's causing this. TP-Link might want to address this ASAP and fix whatever causes it, otherwise this router is not going to do very well in the marketplace if setting it up with Windows 7 PCs with IE9 is a problem. It should work with default settings, same as it seems to with Windows XP and IE8.