Region : Hongkong
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Before my TL-WR702N was working fine as a reperter. After sometime it doesn't work any more, so I try to reset it again but now I couldn't see my SSID after I press the survey buttom in the quick setup - wireless repater page.
Region : Others
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Going to a hotel where they'll charge me (a lot) for WiFi in the room, for only 1 device. Will the TL-WR702N let me share this 1-device internet connection among several devices?
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Just got my new TP-Link device and intend to use it in client mode for my new audio receiver to connect to my home network.Trying to configure the device, and I cannot even access the online utility. I tried using the following address:
192.168.0.254
192.168.1.1
None of these seem to work. Tried on Chrome, then Internet Explorer and made sure that the web browser was not set to proxy (it was not set to this in the first place). The address just doesn't seem to connect, and I get a "This page cannot be displayed" note, as if I'm reaching a bad address.
Region : Italy
Model : TL-WR702N
Hardware Version : Not Clear
Firmware Version :
Android Tablets do not connect to Wifi Ad Hoc network (IBSS).My Nokia phone create an HotSpot WiFi network type AD HOC (IBSS).With TL-WR702N in Bridge or Repeter i connect it to Nokia Phone in "Ad Hoc" mode and creare an AP Wifi infrastructure network that my Android Tablet can connect to it.
Region : United-States
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
my Firmware Version is chinese i can't understand it.i go to tp-link.com go to support the last version is older with compare are old.
Region : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : India
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP : BSNL
702N runs as repeater mode to W8968. In 702N > Maintenance > Diagnostic the ping work for Internal network but fail for external IPs. Most devices connected to 702 can access Internet fine. I have also tried Bridge and Client mode.
Ping to W8968
Code:
Pinging 10.0.0.1 with 64 bytes of data:
Reply from 10.0.0.1: bytes=64 time=1 TTL=64 seq=1
Ping to Internet
Code:
Pinging 8.8.8.8 with 64 bytes of data:
Request timed out.
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Trying to use TL-WR702N in bridge mode at a hotel. For some reason, every time I set the DHCP parameters to enable DHCP, then save and reboot, upon reboot DHCP is disabled. Of course, without DHCP then bridge mode is useless because I cannot then share the hotel wifi connection with multiple devices.Am I missing something obvious, or is there a trick to getting DHCP to be accepted?
Region : United Kingdom
Model : TL-WR702N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.
Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?
In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
How to approach an overnight upgrade from autonomous AP1231/1242 deployment into a 2504 controller-based AP1602 deployment.I do not have access to the existing 1231/1242 deployment ==> I need to ask network manager for all necessary config info to be ported onto the 2504.Example: the 1231 show run output does not list the various SSID that are in use.Therefore the question is: which commands' output do I need to ask to have all possible config data from 1231/1242 to use when configuring the 2504/1602 deployment.
View 2 Replies View RelatedFind list of all the MAC address of the devices connected to the router?
View 2 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
When I click on to my wireless network list nothing shows up, but I use my work pc and about 20 networks show up. What is going on with my lap top.
View 1 Replies View Relatedi have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies View RelatedI have a ASUS PCE-N13 card I am trying to connect to my N network. It is a Netgear WNDR3700 v2 running DD-WRT. It does not even show up in my list of networks, yet I see a neighbor's N network. I updated the drivers and I still do not see it. .
View 2 Replies View RelatedI am having LMS 4.0 Software and taking the Inventory with it, but there is somewhat a strange problem .I CAN SEE THE LMS DISCOVERING MY DEVICES IN NETWORK BUT DOES NOT SHOW IN THE DEVICES LIST(where we see all the devices)
View 3 Replies View RelatedRegion : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
I'm having big problems with my Linksys WAG320N. I'm pretty clueless when it comes to networking.Without changing any of the settings, the other day my Macbook Pro couldn't connect and it kept saying 'Connection timeout'. From that point my iPhone also refused to connect, although accessing the internet on my MBP via Ethernet was fine.
I did a hard reset following instructions from this forum then re-configured with the installation CD. The wireless LED on the router was lit but my MBP couldn't see the network. Eventually I managed to connect after rebooting my laptop, and enjoyed all of 10 minutes of problem-free of wireless internet connectivity before the network just dropped out and now doesn't show up in my list of networks again, although the wireless LED is still on. Connecting via Ethernet still works, just not via wireless.I've rebooted my laptop and the router and tried switching channels on the router, all to no avail.
I created some acess-lists, and you can assign a logging level to this access-list. Now this ACL has a lot of hits, so i want to see whats happening. Only the log I then see is completely empty. I cannot figure out how to get some info in that log.
I think there is some global logging setting i probably need to enable in order to get anything logged at all, but i cannot figure out which.
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
Region : Hongkong
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?
Region : Argentina
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version : 3.12.4 Build 100910 Rel.57694n
I did a hard reset and after that, when i power on the router, it works for aprox. 15 seconds, so i can access the interface at 192.168.1.1, but after those 15 seconds it doesnt respond. The lights are on as if it was perfect, but cant go on admins interface and ping doesnt work either. I did several resets, did the 30/30/30, and clicked on reset to factory defaults on those 15 seconds but nothing happens.
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
wan led on my router is not illuminating. My internet connection is fine.I have pppoe connection. What may be the reason ?
Region : Australia
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
I am posting this in the wrong place but thats only because I cant find the forum for the TL-WR642G ver 3.6 device.Basically I am unable to see any QOS configuration and I wanted to know if this is available to this model ?I know the ver 4.0 firmware update states that QOS is added but can I update a 3.6 device using a ver 4.0 firmware ?
Region : Colombia
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 110915 Rel.40896n
ISP :
i have a TL-WR740N router.I need connect 2 networks.
network 1 => 192.168.1.x connected to WAN port.
network 2 => 10.0.0.0.x connected to LANS port.
Router
assigned address:
192.168.1.101 WAN
10.0.0.225 LAN
[code]....
i can't connect to 10.0.0X network (pcs connected to router lans ports)I need bidirectional connection to networks.
Region : China
Model : TL-WR741N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am American living in China. My Chinese reading is not so good, I am still learning. The interface for my router comes up in Chinese. Is there a way to change the language to English? So far, all I can do is get the set-up interface through IE, but I can not set it up!
Region : Australia
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I have TL-WR740N router. I dont know how to stop and start wifi signals.
Region : Romania
Model : TL-WR740N
Hardware Version : V3
Firmware Version : 3.8.2 Build 080628 Rel.37228n
ISP :
I have a problem with my tplink router. In first of all I can't find my model in this forum. I have TL-WR641G [108M] and I cant upgrade my firmware.
My current firmware is:
Firmware version: 3.8.2 Build 080628 Rel.37228n
Hardware Version: WR641G/642G v3 081520C2
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.
