Linksys Cable / DSL :: WAG320N Network Just Dropped Out / Now Doesn't Show Up In List
Feb 5, 2011
I'm having big problems with my Linksys WAG320N. I'm pretty clueless when it comes to networking.Without changing any of the settings, the other day my Macbook Pro couldn't connect and it kept saying 'Connection timeout'. From that point my iPhone also refused to connect, although accessing the internet on my MBP via Ethernet was fine.
I did a hard reset following instructions from this forum then re-configured with the installation CD. The wireless LED on the router was lit but my MBP couldn't see the network. Eventually I managed to connect after rebooting my laptop, and enjoyed all of 10 minutes of problem-free of wireless internet connectivity before the network just dropped out and now doesn't show up in my list of networks again, although the wireless LED is still on. Connecting via Ethernet still works, just not via wireless.I've rebooted my laptop and the router and tried switching channels on the router, all to no avail.
View 9 Replies
ADVERTISEMENT
Mar 7, 2013
How to approach an overnight upgrade from autonomous AP1231/1242 deployment into a 2504 controller-based AP1602 deployment.I do not have access to the existing 1231/1242 deployment ==> I need to ask network manager for all necessary config info to be ported onto the 2504.Example: the 1231 show run output does not list the various SSID that are in use.Therefore the question is: which commands' output do I need to ask to have all possible config data from 1231/1242 to use when configuring the 2504/1602 deployment.
View 2 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Feb 24, 2011
my device can connect to the wireless network. When i tried to setup the network again it says that no WLAN network found. I have not change any of the setting in the modem it just can't find any WLAN network. I have tried reseting the modem but still no network found.
View 4 Replies
View Related
Jan 11, 2012
I have a little problem with this modem / router WAG320NFrom 6 months now no problem, perfect.For a week now appears that wifi losing signal every 4 / 5 hours:Internet has no problem and the PC connected via Ethernet goes smoothly, while the wi-fi stuff (iphone,ipad,notebook) no longer see the network, but the lights on the modem (including wi-fi) are all green as they should be.To resolve this problem I turn off and on again and the wi-fi again be recognized and work fine for other 4 / 5 hours.i have the latest available firmware and settings areBand 2.4Ghz Mode B / G / N MixedLarge 40-MHz channel width,Wide channel 9 2452 GhzStandard.
View 2 Replies
View Related
Apr 8, 2010
I recently purchased a WAG320N, primarily for the faster networking speeds and the ability to attach a USB hard drive to my network.The only problem is that I have little idea how I get this network storage thing to work. Cisco haven't really supplied any documentation on how to work this.So far I've plugged in a hard drive and formatted it through the router's web interface, with no trouble at all.But, after doing this I have no idea how to access my hard drive on the network.I would assume that it would appear automatically on my network for me to access freely.
View 9 Replies
View Related
Apr 18, 2011
I am having a problem with copying files onto my Storage device Connected to my WAG320N, the router is up to date with the latest updates and has been reset in an attempt to overcome this problem. I currently have attached a 2TB Seagate External Hard drive plugged directly into the router formatted in NTFS, and using Windows 7 Bit to access the Routers Webpage and the External Drive.
I am able to set up permissions and access control all okay, so some users can see some folders or have access in Read only or Read and Write Permissions, however I have been using the Admin account when accessing the drive which has Read and Write permissions to all Folders on the Drive. I can create a new document on the Drive (Right click > New > .Docx or .txt) and save file successfully and can view from other computers from the network, however I cannot Copy from any of the computers to the Network drive (e.g.. Copy .txt file from Computer to Network drive), I get the Windows Transfer Dialog and it Calculates Transfer Rate for a while before telling me it's unable to and that I can either select Try Again which comes up with the same error message, or Cancel the transfer.The reason why I want to be able to Copy files to the Network Drive is so I can centralise all the Photos, Videos and other files and documents to be shared to all computers on the network.
View 1 Replies
View Related
Oct 30, 2011
I have a linksys E3200. Today I got disconnected and when it reconnected it stated that the network was changed to just network and not my usual network name. I was having connection issues with the network disconnecting me and reconnecting me. I uninstalled the cisco connect software. I contacted support who told me to restart the router and modem, which I did. After reset I tried to reinstall the software. Cisco Connect likes to insist to do the installation wirelessly but my laptop can't find the router during installation to complete it. My router is essentially a glorified wire connecting my computer to my modem now.
View 2 Replies
View Related
Jan 31, 2011
When I click on to my wireless network list nothing shows up, but I use my work pc and about 20 networks show up. What is going on with my lap top.
View 1 Replies
View Related
Jun 4, 2010
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
View 8 Replies
View Related
Jul 31, 2011
I recently bought the WAG320N can I block Peer to Peer file sharing on my Network?
View 3 Replies
View Related
May 15, 2012
I have a home network consisting of a Linux machine running dhcpd server, connected to the X3000 router wireless, connected -in turn- to the RE1000 repeater, and -finally- a DHCP client machine.Since I run my own DHCP server, I have configured X3000 to be a Relay.I am getting very strange behaviour. Specifically, the DHCP client sents a DISCOVER packet, which arrives to the server (through the relay/router), the server then replies with an OFFER packet to the Relay, and then - bizarelly! - the relay/router forwards the OFFER reply NOT to the client, but back to the server!Needless to say, when this happens the client does not register with the network.I have captured the packets with wireshark running on the server machine, and you may find them here:url...Does not Linksys have professional online technical support?
View 6 Replies
View Related
Jan 15, 2012
Every once in a while when logging into Windows (7 Ultimate 32 bit) My PC decides it couldn't find a network connection, usually restarting the computer solved the problem, however now I have seemed to permanently be stuck on the "identifying" stage of my LAN connection. My mobo is an Asrock p67 extreme, the network adapter is a realtek pcie family card.Now I know it is not my modem since I can connect on my other PC in the living room, I verified this with a phone call to my ISP, they couldn't see my PC connected to the network but could see the other one.It is not the Ethernet cords, I switched them and even used a new one. I tried rolling back, installing updated and installing factory drivers for my network card, no change.
I tried turning off the PC, disconnected the power cord, discharged it, left everything off/ disconnected for 30 minutes and reattached, powered on, no change.I made sure my DHCP was on and that my PC was set to automatically retrieve IP/DNS.I even bought a new Ethernet card, installed it and I still can't connect, so its not the realtek card.I can't even access my modem using its UP address, 192.168.2.1 (Bell 2wire) but I can on my 2nd PC, it sees all other devices, PS3 /Smartphones but not my PC.
View 19 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Nov 12, 2011
Im working for a client at the moment and I've had to setup a network printer for them, I've got 4 Windows 7 machines easily printing over the network to this printer that is connected wirelessly but they want one of there machines to use the scanning functionality of the printer.The scanner doesn't show up at all in the local network devices like the printer does and to be honest i don't really have any experience with scanning over a network to a windows 7 machine, but this printer does support scan to ftp so my idea is to setup a small ftp server on the windows 7 machine with a folder to stored scans on the desktop or something, then put the details of the server in to the printer making it as easy as possible for the customer to scan stuff and just get it from the folder on the desktop, i could also share this folder over the network for anyone to open and get a scan if needs be.
View 2 Replies
View Related
Jan 20, 2011
I put Win7 on a customed pc bought online. The motherboard has an Atheros L1 integrated NIC and I installed a Dlink dge530t NIC into a PCI slot. I know I have to disable the onboard nic but the installed card is not comming up either in Device manager or network connections. What gives? In the bios under integrated peripherals i did enable PnP OS.
View 4 Replies
View Related
Jul 17, 2011
I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies
View Related
Mar 2, 2011
how to configure or set up VPN on WAG320N?
View 3 Replies
View Related
Aug 27, 2012
I have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.
View 1 Replies
View Related
Mar 6, 2012
How to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.
RFC2684 Bridged
LLC/SNAP
g.dmt or ADSL2+
VPI 0
VCI 100
But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP.
View 7 Replies
View Related
Sep 4, 2012
I'm trying to play some online games and my WAG320N does not forward ports, upnp does not function and to top it off DMZ wont even work (not a software firewall issue either). I have the latest firmware (and honestly the stock firmware is terrible).
Am I out of luck or is there something I can do to fix this? I sure as hell will be steering clear of linksys products after this.
View 1 Replies
View Related
May 16, 2010
i need to downgrade my WAG320N and don't find old firmware 1.00.08 AnnexA
View 9 Replies
View Related
Mar 10, 2011
This WAG320N Router can get really slow after a while use which is really frustrating for me since I am a gamer. Power cycling it SOMETIMES does the trick but it will still get slow. It has been slow just now and over here it is midnight so the internet peak should be down and my internet should be faster but its now.
View 2 Replies
View Related
Nov 8, 2012
I have the WAG320N. I know if my router is updated to fix the bug of the WPS?There is an update? Which is the date scheduled for release? The vulnerability of my network has been compromised yesterday because of this bug, so either the update is released soon or I'll have to switch to another product of some companies more serious
View 3 Replies
View Related
Feb 4, 2011
Transferring a file between a wired Win 7 machine and a wireless Snow Leopard mac seems to top out at 32Mbps.I've seen over 60Mbps on this laptop using N networks before, and when I wire the laptop I get a more respectable 240Mbps (presumably maxing out the server's disk I/O rate), so I'd say the issue is the router.
Things I have already tried:updating the firmware to 1.00.125Ghz modeFinding the least crowded 2.4Ghz channelswide channelsSetting network mode to N-onlySetting the transmission rate to 108Mbpschanging the beacon interval to 50, the frag threshold to 2201 and the RTS threshold to 2202
View 2 Replies
View Related
Oct 12, 2011
I have had my DIR 615 router for about 6 months, and have had no problems. I have a notebook (Sony Vaio) and I also have a Blue-Ray Player and my DirecTV DVR connected by ethernet. Starting a few days ago I was having connectivity issues. At first I could see the network on my Vaio, but the Internet kept coming and going.I did some troubleshooting on the adapter and that seemed to work. Now I am having an issue where every 2 hours or so the wireless drops and the network disappears from the list of available connections on my notebook. I have had my netbook on (connected wireless) and the issues are replicated on that system.
Both of my wired devices do not see any interruption in connectivity. Living in an apartment complex I suspected interference and indeed there are a ton of other networks in range (as per inSSIDer 2.0). As there is no channel that is clearly open, I have set my router to auto channel scan. I also have tried some of the steps outlined in other threads. The thing I am noticing is that when the network connection drops my network (which has a unique name) doesn't even show up on inSSIDer, it just disappears. When working, my network is consistantly in the -25 range on inSIDDer.I should point out also that my notebook is a mere 8 feet from the router, and there are no obstructions.
View 1 Replies
View Related
Jan 26, 2010
I have only purchased this modem a few days ago (upgraded from a working Netgear DGN2000 for Gigabit).... it's solid most the time except for once a day when it needs to be reset.
One morning I accessed a single website, only to find the next wouldn't come up. (approx 7:30am) Lastnight the net was working fine at 11:30pm.... Thismorning I woke up, checked my download manager to find that at 2:30am all queued downloads failed, so the ADSL dropped sometime inbetween then.
The LAN and Wifi still work fine, when I go into the settings and click "reconnect" nothing happens. I need to turn the modem off for a min before it works ok. There is no newer firmware as of yet to try.
View 5 Replies
View Related
Jan 14, 2012
I do not have a "storage" tab in my setup screen. I have Setup, Security, Wireless, etc. According to its manual there must be a Storage tab between security and wireless. Mine doesn't have it. USB drive is connected and I see "mywag320n" on the network but I can't access it because it requires login and password (which I guess I must set up from Storage tab )
View 8 Replies
View Related
Jul 9, 2011
I connected my Western Digital Studio II 2TB external harddrive which is formatted NTFS. I can access the drive and read it. But I can't write it. It says I do not have rights. I tried to get to be the owner of the device but it gave some kind of error.
View 2 Replies
View Related
May 28, 2012
I need to configure my modem router wag320n let pass the magic packet to turn on my computer from the internet. I've already opened the door 7 to the computer ip but does not work. The bios and the OS are perfectly configured.
View 8 Replies
View Related
Feb 13, 2011
I have recently bought a WAG320N modem Gigabite router to substitute the modem router supplied by the internet service provider (in theory less performant).
Formerly I have a wireless router Zyxel (MOD. P660HW-D1). The main computer is wired (connected trough ethernet), I have also a NAS device (WD mybook world 1TB with Twonky as server) wired and a third wired connection for the above mentioned PLK 300. The PLK 300 (4 Inputs and one output) is used to connect a TV (Sony BRAVIA) a Bluray (SONY) a PS3 (Sony) and a multimedia HD (DVICO). All this was working properly. I have internet access from TV, PS3,... I was able to run videos, photos,... stored in the NAS from TV,....
I decided to change for improving the transfer speed and to allow a better wireless connection (I have initially coverage problems, but because I only use the wireless rarely...).Initially I bought a Linksys E 3000 (I thought it was possible to connect it directly to internet and not trough a modem. I asked to several people and in several shops but no one told me this was not possible). That was my first failure: I would like to suggest the liknsys people to clearly explain this on the product sheet to avoid that not very well informed people like me commit the same error.
Then I chaged the E3000 by the WAG320N. I connect the new modem-router like the former (Zyxel). No room for big errors, just the power, DSL line and ethernet cables. It works for the PC and the NAS but the PLC (PLK300) do not appears to work. Several tries later (including plugin the PLK on the line 1 input of the router it is shown on the network map but do not work. I do not have access to the internet nor to the NAS contents form TV,....
I go back to the former router and everything works again in the simplest way (I have internet access form TV,...) except the Twonky access to the NAS from TV ¿?. I do not know exactly what I have changed,...)
View 1 Replies
View Related
Sep 10, 2010
How do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.
View 8 Replies
View Related
Jul 14, 2010
how to make in WAG320N second PVC for IP TV. It looks like unsupportable feature May be next firmware will include it? Or better to change the device? What Linksys with ADSL are support IP TV?
View 3 Replies
View Related
