Linksys Wireless Router :: E3200 - Network Doesn't Show Up Anymore
Oct 30, 2011
I have a linksys E3200. Today I got disconnected and when it reconnected it stated that the network was changed to just network and not my usual network name. I was having connection issues with the network disconnecting me and reconnecting me. I uninstalled the cisco connect software. I contacted support who told me to restart the router and modem, which I did. After reset I tried to reinstall the software. Cisco Connect likes to insist to do the installation wirelessly but my laptop can't find the router during installation to complete it. My router is essentially a glorified wire connecting my computer to my modem now.Â
View 2 Replies
ADVERTISEMENT
Aug 19, 2012
I have just upgraded my E3200 to firmware: 1.0.04 build 1Â Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
View 6 Replies
View Related
Dec 2, 2011
My entire floor receives wifi from a D-Link router box. For the first 4 months, my laptop was able to find and connect to our wifi fine. Last night the internet crashed. All of my German housemates have internet again, but my laptop does not show the network anymore. My wireless card picks up all the other signals in range, but not our router's. I can only get internet with an ethernet cable.
View 1 Replies
View Related
Sep 23, 2010
I recently bought a Linksys WAG160N v2 model to replace my old setup of a Linksys WRT54GL + ASUS AM604g (ADSL2+ Modem) i had.I've set it up to dial my ISP's PPPoE connection as i had on the previous setup exactly, And it seemed to work at first.But now i've randomly noticed the connection just dies - the router doesn't respond to wireless at all anymore, and connecting from a wired machine shows the PPPoE link died, while the log says something along the lines of "PPPoE connection terminated: transport endpoint not connected" followed by a big number with lots of zeros and :'s. Probably some kind of IPv6 error address? note that i am not using IPv6 myself nor does my ISP provide any such addresses.
Â
I've already upgraded the firmware to latest and installed the newest WiFi drivers on the machine i was connecting from wirelessly (has an Intel Wifi Link AGN5300 module).
View 9 Replies
View Related
Sep 8, 2012
i have a 2tb seagate expansion formatted ntfs. i am primarily a linux (ubuntu) user, but when the drive drops off, it cannot be seen in any os and it doesn't show up on the router setup page.
View 6 Replies
View Related
Jul 18, 2011
Comcast sent out a new modem a few days ago. The reason for this was our internet had gone out for a while, they came in and said our modem was fried. I have internet access by directly wiring from the modem to my computer.My router doesn't work anymore. I have a local network, but no internet access. I'm using a Linksys WRT54G, and I don't really know what to do.As far as I remember, setting everything to defaults and factory settings was how I set up my router in the first place and it just worked.
View 11 Replies
View Related
Aug 19, 2012
Buy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
View 3 Replies
View Related
Oct 19, 2011
We have a old Router and a new one(the Lynksys). The old one had problems with the Wifi so we bought this one. So when we connect This Router to the Modem it doesn't show connection to the internet. (The Setup fails because of this). But with the old one it does connect to the internet. So either my modem doesn't detect the new router or vice versa. So I am not sure why its not working since on the old one it works fine.
View 1 Replies
View Related
Feb 13, 2011
I've just bought this wireless usb today and attempted 2-3 times to be able to connect with my router (D-Link's DIR-601) but it for some reason failed to do so, until the little usb didn't have its green light flashing anymore... and when i reconnected it to my Windows XP it rang its error sound... and I kept having this message from the Wireless Wizard that it's not connected appropriately or something...and that i have to run the setup wizard again.
View 1 Replies
View Related
Jul 27, 2011
i am having an annoying issue with my wrt400n and my foscam FI8918W. in the dhcp reservation tab, the wrt400n doesn't show the foscam anywhere in the tab. it shows all laptops, cell phones, nases, etc. if i use the cisco connect software it does show it in the network map. i can probably add it manually via the gui. is this something normal or security cams not considered devices?
View 1 Replies
View Related
Oct 8, 2011
I'm trying to register my new linksys e2000-ew wireless router but it doesn't show up in the selection pull down menu. When I try the e2500 it says my serial# isn't correct.
View 5 Replies
View Related
Feb 5, 2011
I'm having big problems with my Linksys WAG320N. I'm pretty clueless when it comes to networking.Without changing any of the settings, the other day my Macbook Pro couldn't connect and it kept saying 'Connection timeout'. From that point my iPhone also refused to connect, although accessing the internet on my MBP via Ethernet was fine.
Â
I did a hard reset following instructions from this forum then re-configured with the installation CD. The wireless LED on the router was lit but my MBP couldn't see the network. Eventually I managed to connect after rebooting my laptop, and enjoyed all of 10 minutes of problem-free of wireless internet connectivity before the network just dropped out and now doesn't show up in my list of networks again, although the wireless LED is still on. Connecting via Ethernet still works, just not via wireless.I've rebooted my laptop and the router and tried switching channels on the router, all to no avail.
View 9 Replies
View Related
May 1, 2013
I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
View 2 Replies
View Related
Sep 29, 2011
I have an N wireless adapter for my xbox 360. I want to make sure I am connected through N network, getting 5gbps.
View 6 Replies
View Related
Feb 19, 2012
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
View 9 Replies
View Related
Jul 23, 2012
I recently replaced my old WRT54G router with a E3200 router.
Â
Unfortunately, ever since my wireless network is a lot more unstable than before. I very often experience serious lag spikes and drops in speed. Very often I experience serious lag for a couple of seconds after which everything returns to normal. I notice this the most in online gaming, but it is also noticeable while browsing the web. When downloading large files (e.g. steam games), the download speed also seems to suffer from this by dropping every now and then.
Â
There are no connection drops however. And it only seems to affect the wireless network.
Â
I have configured the E3200 router manually using the Web UI and is has been configured exactly the same as my WRT54G: i.e. only 2.4GHz band enabled with b/g/n, WPA2 security, MAC filtering on, no throtling/parental control/port forwarding, UPnP disabled. The E3200 is in the exact same place as the the WRT54G was.
Â
Things I have done so far for troubleshooting: I used inSSIDer to monitor the wireless network and it's signal strength seems about the same as the WRT54G. I changed channels for best signal strength (there is only one other wifi network that seems to be configured as a dual channel N network; 3 other networks with very low signal strength) and have tried every channel.
Â
I updated the fimware to the latest version (Ver.1.0.04 (Build 1)) and did a factory reset and power cycle afterwards.
Â
I noticed that switching channels can account for 5-10Mbps differences in internet speed. Something I never noticed with the WRT54G. The lag spikes occur more often on some channels than on others. This seems not related to the speeds I get on the channel.
Â
I really can't imagine that a router marketed as High Peformance router with superior speed and superior range is less stable than my old WRT54G router.
Â
Is there something I can do to improve stability of this router?
View 5 Replies
View Related
Dec 25, 2011
The issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies
View Related
Jan 15, 2012
Every once in a while when logging into Windows (7 Ultimate 32 bit) My PC decides it couldn't find a network connection, usually restarting the computer solved the problem, however now I have seemed to permanently be stuck on the "identifying" stage of my LAN connection. My mobo is an Asrock p67 extreme, the network adapter is a realtek pcie family card.Now I know it is not my modem since I can connect on my other PC in the living room, I verified this with a phone call to my ISP, they couldn't see my PC connected to the network but could see the other one.It is not the Ethernet cords, I switched them and even used a new one. I tried rolling back, installing updated and installing factory drivers for my network card, no change.
I tried turning off the PC, disconnected the power cord, discharged it, left everything off/ disconnected for 30 minutes and reattached, powered on, no change.I made sure my DHCP was on and that my PC was set to automatically retrieve IP/DNS.I even bought a new Ethernet card, installed it and I still can't connect, so its not the realtek card.I can't even access my modem using its UP address, 192.168.2.1 (Bell 2wire) but I can on my 2nd PC, it sees all other devices, PS3 /Smartphones but not my PC.
View 19 Replies
View Related
Jan 15, 2012
In the next month or so I plan to replace my old desktop PC. It is currently connected to a Linsys E3200 wireless router. I have many other wireless devices also running off the E3200, but my PC is the only wired device connected to it. When I replace the wired PC do I simply switch the new one in with the existing ethernet connection (I'm sure it is not that simple) or do I have to start over again recreating my entire network..security etc.. ? If so what is the process to start over ? Do I have to reset something on the router, reload cisco connect, create a new network name?
View 4 Replies
View Related
Sep 23, 2012
I tried searching google and Cisco Home Community for this answer, but no luck. Maybe I didn't phrase my search correctly. I have an external drive connected to a mac mini which is shared on the network. When transferring folders to or from that external drive, our internet connection stops working until the transfer finishes, then comes back up. I've tested this in a variety of ways. Any transfer of data from shared folders in any combination of devices causes internet to stop working both on wired and wireless devices until the transfer is done, then they all work again. Router firmware: 1.0.03.
View 9 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Jun 16, 2012
I have a laptop that I want to sell, therefore I went to somebody to see my laptop and wanted to connect to his wifi. After repeatedly entering the pass for the wifi ,the wifi was still not connecting.
1. My laptop will see his wifi but after entering the pass will not connect
2. The pass is correct because I introduced the same pass on my mobile and I was able to connect to his wifi through my mobile
3 My laptop wifi is working fine because when I went home it connects automatically on my home wifi
4. I tried to open and close his router but I faced same problem.
View 2 Replies
View Related
Nov 12, 2011
Im working for a client at the moment and I've had to setup a network printer for them, I've got 4 Windows 7 machines easily printing over the network to this printer that is connected wirelessly but they want one of there machines to use the scanning functionality of the printer.The scanner doesn't show up at all in the local network devices like the printer does and to be honest i don't really have any experience with scanning over a network to a windows 7 machine, but this printer does support scan to ftp so my idea is to setup a small ftp server on the windows 7 machine with a folder to stored scans on the desktop or something, then put the details of the server in to the printer making it as easy as possible for the customer to scan stuff and just get it from the folder on the desktop, i could also share this folder over the network for anyone to open and get a scan if needs be.
View 2 Replies
View Related
Jan 20, 2011
I put Win7 on a customed pc bought online. The motherboard has an Atheros L1 integrated NIC and I installed a Dlink dge530t NIC into a PCI slot. I know I have to disable the onboard nic but the installed card is not comming up either in Device manager or network connections. What gives? In the bios under integrated peripherals i did enable PnP OS.
View 4 Replies
View Related
Oct 12, 2011
I have had my DIR 615 router for about 6 months, and have had no problems. I have a notebook (Sony Vaio) and I also have a Blue-Ray Player and my DirecTV DVR connected by ethernet. Starting a few days ago I was having connectivity issues. At first I could see the network on my Vaio, but the Internet kept coming and going.I did some troubleshooting on the adapter and that seemed to work. Now I am having an issue where every 2 hours or so the wireless drops and the network disappears from the list of available connections on my notebook. I have had my netbook on (connected wireless) and the issues are replicated on that system.
Both of my wired devices do not see any interruption in connectivity. Living in an apartment complex I suspected interference and indeed there are a ton of other networks in range (as per inSSIDer 2.0). As there is no channel that is clearly open, I have set my router to auto channel scan. I also have tried some of the steps outlined in other threads. The thing I am noticing is that when the network connection drops my network (which has a unique name) doesn't even show up on inSSIDer, it just disappears. When working, my network is consistantly in the -25 range on inSIDDer.I should point out also that my notebook is a mere 8 feet from the router, and there are no obstructions.
View 1 Replies
View Related
May 28, 2012
i have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : WR1043ND
The router is not showing my external hard drive in the usb settings. The Hard drive is a seagate 7200rpm 1.5tb. The hard drive works just fine when plugged into my computer. I have tried NTFS and EXFAT. My 2gb usb drive in FAT32 shows up just fine. The external has its own power supply. Is there anything I am missing that would cause it to not work?
View 5 Replies
View Related
Jun 5, 2011
We have a VPN setup for a customer between our shop and their shop 2.5 hours away. This is a Cisco 871.We had Verizon and the connection worked (still does) great! We had to switch providers as they sold to Frontier and were going to change our IPs anyways so why not switch to a faster provider instead.We switched to Charter. I have ZERO, NADA, ZILTCH knowledge of Cisco and I plan to keep it that was as they are way more complicated then they should be. Ill stay with my Sonicwall.....Anyways.... I took the config and did a find and replace for all the IP's, Gateways, DNS etc....I blasted that into the router and it took right off and connected up the VPN in a matter of 2 minutes. I was estatic as I knew I was going to sleep good that night not worrying about it..............Untill the next day at 11 am when I get a phone call from work saying the connection was down.
Â
I go and realize that the router cant see the outside world anymore, therefor was obviously not going to see the peer IP address. I was dumbfounded!. To make a long story short I tried reconfiging therouter with the same file. I even redid the find and replace and resaved it to no avail. Still no go, no internet. All the proper IPs, Gateways and DNS numbers are where they should be. To test that its the config and/or something to far above me. I re configed the router with the old config and hooked it back up to verizon, it took right off and reestablished the VPN and was working.
View 6 Replies
View Related
Jul 25, 2011
I have a W7 PC 64 bit system and I've been trying to port forward the port 25565 for my Minecraft server. However for some reason (even after port forwarding the right one) people still can't connect. When I check on Open Port Check Tool - Test Port Forwarding on Your Router It still says that the port 25565 is closed!I've even created an Inbound and Outbound rule in the Windows Firewall advanced settings. I use Avira Anti-vir fyi..
View 19 Replies
View Related
Jan 4, 2012
A couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies
View Related
Jan 8, 2012
The linksys E3000 Could really use a firmware update.. the last one was 12/01/2010Ver.1.0.04 (build 6)
View 6 Replies
View Related
Oct 12, 2011
Hardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
 Â
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked. Â
Â
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
Â
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
Â
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
View 2 Replies
View Related
Jan 12, 2012
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
View 3 Replies
View Related
