Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Just got my new TP-Link device and intend to use it in client mode for my new audio receiver to connect to my home network.Trying to configure the device, and I cannot even access the online utility. I tried using the following address:
192.168.0.254
192.168.1.1
None of these seem to work. Tried on Chrome, then Internet Explorer and made sure that the web browser was not set to proxy (it was not set to this in the first place). The address just doesn't seem to connect, and I get a "This page cannot be displayed" note, as if I'm reaching a bad address.
Region : United Kingdom
Model : TL-WR702N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.
Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?
In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.
Region : Others
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Going to a hotel where they'll charge me (a lot) for WiFi in the room, for only 1 device. Will the TL-WR702N let me share this 1-device internet connection among several devices?
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : Italy
Model : TL-WR702N
Hardware Version : Not Clear
Firmware Version :
Android Tablets do not connect to Wifi Ad Hoc network (IBSS).My Nokia phone create an HotSpot WiFi network type AD HOC (IBSS).With TL-WR702N in Bridge or Repeter i connect it to Nokia Phone in "Ad Hoc" mode and creare an AP Wifi infrastructure network that my Android Tablet can connect to it.
Region : United-States
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
my Firmware Version is chinese i can't understand it.i go to tp-link.com go to support the last version is older with compare are old.
Region : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
Region : Hongkong
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Before my TL-WR702N was working fine as a reperter. After sometime it doesn't work any more, so I try to reset it again but now I couldn't see my SSID after I press the survey buttom in the quick setup - wireless repater page.
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : India
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP : BSNL
702N runs as repeater mode to W8968. In 702N > Maintenance > Diagnostic the ping work for Internal network but fail for external IPs. Most devices connected to 702 can access Internet fine. I have also tried Bridge and Client mode.
Ping to W8968
Code:
Pinging 10.0.0.1 with 64 bytes of data:
Reply from 10.0.0.1: bytes=64 time=1 TTL=64 seq=1
Ping to Internet
Code:
Pinging 8.8.8.8 with 64 bytes of data:
Request timed out.
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Trying to use TL-WR702N in bridge mode at a hotel. For some reason, every time I set the DHCP parameters to enable DHCP, then save and reboot, upon reboot DHCP is disabled. Of course, without DHCP then bridge mode is useless because I cannot then share the hotel wifi connection with multiple devices.Am I missing something obvious, or is there a trick to getting DHCP to be accepted?
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
Region : Philippines
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 120320
ISP : Smart Bro
i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?
Region : Colombia
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 110915 Rel.40896n
ISP :
i have a TL-WR740N router.I need connect 2 networks.
network 1 => 192.168.1.x connected to WAN port.
network 2 => 10.0.0.0.x connected to LANS port.
Router
assigned address:
192.168.1.101 WAN
10.0.0.225 LAN
[code]....
i can't connect to 10.0.0X network (pcs connected to router lans ports)I need bidirectional connection to networks.
Region : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP : ShawCable
I have just bought the device. I works fine as a AP out of the box. I want to use it as a repeater of my wireless network which uses a Linksys Simultaneous Dual Band N Router WRT400N
1. To do the setup, I have tried to login at 192.168.0.254 I cannot do this (a) using a wireless connection to a Linksys router which is connected to the cable modem and (b) wired connection to the router which is connected to the cable modem. The attempts get a timeout messaage.
2. The default gateway is 192.168.1.1. The DHCP server has the same address. My computer is using 192.168.1.101.
3. I use McAfee Internet Security software.
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
I am facing some issue in LAN network.I have connected one desktop( win 7) and another desktop (win xp) to the TP link router. Both the computers got ip address and able to share the internet. But both the computers are not in the same network. That is they cant PING each other. hence they are not visible to each other.
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
I seted up router and i coud acces the utility window, then i switced from w7x32 to w7x64 and then i try to acces the utility window i can only see.Username or Password is incorrect.Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". The settings will be restored to factory default after the resetting.
How to restore the device to the factory default settings?Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings.no pop up window appears i tried looking this up and the closest thing i found was to un-check the proxy but its not checked so what should i do to be able to access utility window?
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR741ND
Hardware Version : V4.20.0
Firmware Version : 3.12.11
As you can see it's a simple network, I mostly use the network to share itunes library from PC CENTRAL to the other pcs, play games like counter strike and the like, and of course share the internet connection and copy files from one to another. I have to puntualize that all the computers are in the same room.Last week my mom bought a Toshiba Satellite and I bought a TP-LINK TL-WR741ND so she can work in her room (which is pretty far if I want to make a wire connection), so I installed the WiFi but now this is how my network looks like:> The case is that:
a) I can't access my toshiba from any other computer, but the toshiba can access any other using \192.168.1.# command.
b) The PC Central's iTunes library can be played in toshiba's itunes.
c) I can't make an HomeGroup between the two pcs running w7. Actually the only one pc I want to be working in LAN with the toshiba is PC Central, but as I said earlier, PC Central can't access toshiba.
The settings in the TL-WR740N are: WAN working as Dynamic IP (got IP 192.168.1.46 submask 255.255.255.0 and gateway empty), lan 192.168.0.1, (I can't make it to be 192.168.1.#, I think that's impossible cause it always gives me an error 5008). MAC filtering and that's the only thing I changed from default settings.
Region : Ireland
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
I am trying to setup my DVR for remote access but my public IP and the routers WAN are not the same?
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
I have high speed internet connection. The following image shows how my ISP provides internet connections:
ISP.jpg
I am required to put IP address in my computer network settings. This IP is used to go to login page to put username/password. It is a web based authentication(kind of captive portal you can call). Done! I am connected to the internet. Super fast!Now, I would like to share this internet connection between two computers using WR741ND router. So, what I am doing is having both these two computers connected to the router using LAN ports whereas my ISP cable to the WAN port of the router. IP settings of both the computers are set to: Obtain IP address automatically.Configuration in the router:
Logged into the router--->Network--->WAN--->Static IP--->Settings saved
I am able to connect to the internet using any of the PCs. The problem is I am unable to access the internet simultaneously using both the computers. When one computer is in the process of loading website and I try to open a website on second computer the second computer does not start loading website at all and even the first computer stops opening the website.What change do I need to make in the router configuration? Can this internet connection be shared at all?
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
Region : Ireland
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Three Mobile
I have recently purchased a new desktop computer that does not have an internal WiFi card. To remedy this I bought the TP Link TL-WR702N. Currently my access to the internet is provided by a mobile WiFi router (one of these: { URL}, that spreads a wireless signal throughout my house for things like my phone and laptop to connect to. I was under the impression that the WR702N would be able to connect to this network and let my new computer run on it (I believe it's called client mode?)
Now so far I have not been able to get my computer to recognize the existence of the TP Link modem, despite both Ethernet and USB cables being plugged into the computer. I think I need both logging in and changing the mode from AP to client mode.
I emailed support and was given the instruction to read this FAQ [URL], however, when following those instructions, after clicking on "Change adapter settings" instead of reading the router, all I get is a blank screen.
Region : Argentina
Model : TL-WR741ND
Hardware Version : V4
Firmware Version : 3.13.12
ISP : Triple C
I'm trying to set up my new WR741ND router to replace the old WR541G with excctly the same cabling,ISP account etc.
All seem to be working i.e. I get the PPPoE connection against the ISP and cat ping by name to Internet addresses from THE ROUTER.Also I get DHCP handing out addresses both to my desktop connection by Ethernet cable and to my laptop via Wifi.And the computers may ping the router and also connect its admin GUI.However,the computers stop at the router and can't go further.All they can go is to the router as if it doesn't route between LAN and WAN.With the 541 router everything works and as I said it has the same setup (very basic,no static routes or anything too smart).
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : Lexus
I am using tp link router for accessing internet in my laptop and mobile. everything is opening in my laptop but i had few problems when using internet in mobile. im using android mobile. when using play store the images and screen shots of applications are not loading but im able to download. I'm unable to see the images in play store. So I'm thinking that there is something problem in router settings.
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : I am trying to set up my router for about 2 days without any effect.
Here you can find, what I have to do to connect through Ethernet cable to the internet at our university:[url]....
When I set auto-detect IP on router, it says that I have Static IP. In CMD I can find out all the information about the connection and the licence is usually for one day (automatically renewing). I've also tried to clone MAC address, nothing happened.
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :
I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.
I am trying to setup a DIR-601 wireless router (Hardware Version: A1 Firmware Version : 1.00NA ) with my connection from Astound.I am able to connect to the internet from the cable modem (Motorola SURFboard SB5101) but I am unable to get it to work through the router. All the lights on the router look ok.When I look at the WAN status from the router setup page I see :
WAN
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Disconnected
Connection Up Time : N/A
[code]....
* I noted that the router did not show me the correct time. Is that normal ?I have even copied my laptop's MAC address but it did not work. I restarted the modem and the router a number of times but to no avail.