TP-Link 150Mbps Wireless :: WR741ND Does Not Route Between Local LAN And The Internet
Dec 1, 2012
Region : Argentina
Model : TL-WR741ND
Hardware Version : V4
Firmware Version : 3.13.12
ISP : Triple C
I'm trying to set up my new WR741ND router to replace the old WR541G with excctly the same cabling,ISP account etc.
All seem to be working i.e. I get the PPPoE connection against the ISP and cat ping by name to Internet addresses from THE ROUTER.Also I get DHCP handing out addresses both to my desktop connection by Ethernet cable and to my laptop via Wifi.And the computers may ping the router and also connect its admin GUI.However,the computers stop at the router and can't go further.All they can go is to the router as if it doesn't route between LAN and WAN.With the 541 router everything works and as I said it has the same setup (very basic,no static routes or anything too smart).
View 4 Replies
ADVERTISEMENT
Jan 23, 2013
I have high speed internet connection. The following image shows how my ISP provides internet connections:
ISP.jpg
I am required to put IP address in my computer network settings. This IP is used to go to login page to put username/password. It is a web based authentication(kind of captive portal you can call). Done! I am connected to the internet. Super fast!Now, I would like to share this internet connection between two computers using WR741ND router. So, what I am doing is having both these two computers connected to the router using LAN ports whereas my ISP cable to the WAN port of the router. IP settings of both the computers are set to: Obtain IP address automatically.Configuration in the router:
Logged into the router--->Network--->WAN--->Static IP--->Settings saved
I am able to connect to the internet using any of the PCs. The problem is I am unable to access the internet simultaneously using both the computers. When one computer is in the process of loading website and I try to open a website on second computer the second computer does not start loading website at all and even the first computer stops opening the website.What change do I need to make in the router configuration? Can this internet connection be shared at all?
View 2 Replies
View Related
Jan 5, 2013
Region : Argentina
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version : 3.12.4 Build 100910 Rel.57694n
I did a hard reset and after that, when i power on the router, it works for aprox. 15 seconds, so i can access the interface at 192.168.1.1, but after those 15 seconds it doesnt respond. The lights are on as if it was perfect, but cant go on admins interface and ping doesnt work either. I did several resets, did the 30/30/30, and clicked on reset to factory defaults on those 15 seconds but nothing happens.
View 3 Replies
View Related
Apr 21, 2013
Region : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
View 3 Replies
View Related
Feb 7, 2013
Region : Others
Model : TL-WR741ND
Hardware Version : V4.20.0
Firmware Version : 3.12.11
As you can see it's a simple network, I mostly use the network to share itunes library from PC CENTRAL to the other pcs, play games like counter strike and the like, and of course share the internet connection and copy files from one to another. I have to puntualize that all the computers are in the same room.Last week my mom bought a Toshiba Satellite and I bought a TP-LINK TL-WR741ND so she can work in her room (which is pretty far if I want to make a wire connection), so I installed the WiFi but now this is how my network looks like:> The case is that:
a) I can't access my toshiba from any other computer, but the toshiba can access any other using \192.168.1.# command.
b) The PC Central's iTunes library can be played in toshiba's itunes.
c) I can't make an HomeGroup between the two pcs running w7. Actually the only one pc I want to be working in LAN with the toshiba is PC Central, but as I said earlier, PC Central can't access toshiba.
The settings in the TL-WR740N are: WAN working as Dynamic IP (got IP 192.168.1.46 submask 255.255.255.0 and gateway empty), lan 192.168.0.1, (I can't make it to be 192.168.1.#, I think that's impossible cause it always gives me an error 5008). MAC filtering and that's the only thing I changed from default settings.
View 4 Replies
View Related
Dec 11, 2012
Model : TL-WR741ND
Hardware Version : V1
Firmware Version :
ISP : EOLO
give me procedure for connecting WiFi to iPhone.The phone recognizes the router, but will not connect.No numbers, i.e. 192.168.1.1, etc are loaded No DNS loaded?
View 2 Replies
View Related
Apr 20, 2013
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 130325
ISP :
I have the firmware v130205 and the latest 130325 does not load as its size is too much by some bytes.(4096 vs 3969 expected.)
View 8 Replies
View Related
Mar 31, 2013
Region : Argentina
Model : TL-WR741ND
Hardware Version : V4
Firmware Version : 3.16.4 Build 130205 Rel.63090n
ISP : Fibertel
My TL-WR741ND is about 1 year and a half old, it was working fine until about 2 weeks ago. I need to reset it, times between resets is not consistent, meaning, it can take 30 minutes, or 8 hours, but it needs to be reset. Right now, there are 2 wired connections (PS3 and Desktop PC) and 7 wireless (4 cell phones, 2 notebooks and 1 netbook). 1 of the notebooks has static IP, and it also has a VM running, with another static IP. Also some port forwarding simply stopped working (ports 80 and 1180), the rest of the ports work flawlessly, but trying to forward the port 80 and 1180 (to the 2 static ips) won't work. I already upgraded the firmware, and the problem persists, also changed the channel (from 6 to 1, and then from 1 to 11).
Installing dd-wrt/openwrt/gargoyle or anything like that, is not an option. The only reason why I bough t this router, was because I could use dd-wrt, I installed it 1 year and a half ago, and it simply sucked, the wireless bandwidth was non existent, and it was a headache. I installed it again last week, to see if it could be a solution, and I was not even able to save changes in the control panel. I need a real solution, and installing a firmware that works only on chrome is not an option (specially when I use Firefox, and I needed to install chromium just to erase dd-wrt)
View 2 Replies
View Related
Feb 24, 2013
Region : China
Model : TL-WR741ND
Hardware Version : V4
Firmware Version :
ISP :
My router box and the router itself are listed as 741N. I find no reference in the forums or on the website to this model. During setup, I can ping the router from the cmd prompt, but then it fails during the Easy-Setup assistant. I need to use the Easy setup because the language is otherwise Chinese, but it fails the network test. One of the two messages it sends are "Check the Model number". Is this a possibility? Is there a work around or where can I find the proper Setup Assistant software?
View 3 Replies
View Related
Feb 18, 2013
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
View 12 Replies
View Related
May 13, 2013
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
View 3 Replies
View Related
Oct 7, 2011
I'm trying to have a website name: remote.test.com route to a local IP address but can't seem to get it working with this router. I don't want to use the windows hosts file as there are different Operating Systems that will connect and so routing though this D-Link is the only option. I have my wireless router connected to a separate network switch though it's WAN port where other computers sit as well as the target machine. I can use the internet as normal like this so things are working fine.
[code]...
View 7 Replies
View Related
Oct 11, 2012
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
View 4 Replies
View Related
Mar 13, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
View 14 Replies
View Related
May 1, 2013
Region : Ireland
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Three Mobile
I have recently purchased a new desktop computer that does not have an internal WiFi card. To remedy this I bought the TP Link TL-WR702N. Currently my access to the internet is provided by a mobile WiFi router (one of these: { URL}, that spreads a wireless signal throughout my house for things like my phone and laptop to connect to. I was under the impression that the WR702N would be able to connect to this network and let my new computer run on it (I believe it's called client mode?)
Now so far I have not been able to get my computer to recognize the existence of the TP Link modem, despite both Ethernet and USB cables being plugged into the computer. I think I need both logging in and changing the mode from AP to client mode.
I emailed support and was given the instruction to read this FAQ [URL], however, when following those instructions, after clicking on "Change adapter settings" instead of reading the router, all I get is a blank screen.
View 1 Replies
View Related
Dec 14, 2011
we just recently upgraded our router from an old model of d-link to tp link's tl-wr741nd. the wireless router was set up fine. but we noticed that we now experienced disconnection problems. our internet would just disconnect and then connect again every 5 minutes or so. but when i check the modem everything's fine. lights are on. even the lights on the modem are on. this problem never happened on our old router. is this possibly because of the N technology our new router has?
View 13 Replies
View Related
Dec 5, 2012
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
View 2 Replies
View Related
Dec 7, 2012
Region : Philippines
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 120320
ISP : Smart Bro
i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?
View 2 Replies
View Related
Mar 7, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : Lexus
I am using tp link router for accessing internet in my laptop and mobile. everything is opening in my laptop but i had few problems when using internet in mobile. im using android mobile. when using play store the images and screen shots of applications are not loading but im able to download. I'm unable to see the images in play store. So I'm thinking that there is something problem in router settings.
View 4 Replies
View Related
Apr 16, 2013
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : I am trying to set up my router for about 2 days without any effect.
Here you can find, what I have to do to connect through Ethernet cable to the internet at our university:[url]....
When I set auto-detect IP on router, it says that I have Static IP. In CMD I can find out all the information about the connection and the licence is usually for one day (automatically renewing). I've also tried to clone MAC address, nothing happened.
View 1 Replies
View Related
May 7, 2013
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
View 12 Replies
View Related
Apr 24, 2013
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :
I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.
View 8 Replies
View Related
Jul 12, 2012
I have to connect through VPN for work so that I can RDP into my remote development machine, but their internet speed is painfully slow. Is there any way I can route my general internet browsing traffic through my local connection, while still maintaining the VPN connection to my remote box?
View 1 Replies
View Related
Feb 21, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
how to setup an adhoc network using TPLINK WR740N without using any internet connection?I want to setup a WLAN connection between my Desktop and 2 other Laptops for file transfer and sharing.... how to search and connect to other available wifi networks using my router?
View 3 Replies
View Related
Dec 22, 2012
This router was just purchased this past week. I have 1 laptop, 1 desktop, and 1 netbook that is connecting to this (along with various smartphones). Set it all up according to the booklet, and ran into some trouble. When connecting through wireless, I only have "Local only" on the older laptop and desktop PC, but full internet access through the smartphones and the netbook. But, when I connect through LAN with the laptop, I have internet connection (only through LAN, not wireless). I suspect this also occurs on the PC, but the two are no where near each other to attempt. I installed the latest firmware version to no avail, and had done a full reset on the router and reinstalled it.
View 1 Replies
View Related
Nov 10, 2012
I have an dir-615 h2 with upgraded firmware to 8.03 instead of the default that was 8.02, now it crashes and i cant reach the router on cable or wireless. its dead and i have to restart it to work.. where can i find the h2 8.02 firmware.
View 7 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
May 13, 2013
Region : Hongkong
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?
View 4 Replies
View Related
Mar 3, 2013
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
View 2 Replies
View Related
Apr 12, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
wan led on my router is not illuminating. My internet connection is fine.I have pppoe connection. What may be the reason ?
View 1 Replies
View Related
Jan 26, 2013
Region : Australia
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
I am posting this in the wrong place but thats only because I cant find the forum for the TL-WR642G ver 3.6 device.Basically I am unable to see any QOS configuration and I wanted to know if this is available to this model ?I know the ver 4.0 firmware update states that QOS is added but can I update a 3.6 device using a ver 4.0 firmware ?
View 2 Replies
View Related
Mar 29, 2013
Region : Others
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Going to a hotel where they'll charge me (a lot) for WiFi in the room, for only 1 device. Will the TL-WR702N let me share this 1-device internet connection among several devices?
View 1 Replies
View Related
Apr 25, 2013
Region : Colombia
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 110915 Rel.40896n
ISP :
i have a TL-WR740N router.I need connect 2 networks.
network 1 => 192.168.1.x connected to WAN port.
network 2 => 10.0.0.0.x connected to LANS port.
Router
assigned address:
192.168.1.101 WAN
10.0.0.225 LAN
[code]....
i can't connect to 10.0.0X network (pcs connected to router lans ports)I need bidirectional connection to networks.
View 3 Replies
View Related
