Region : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
Region : Argentina Model : TL-WR741ND Hardware Version : Not Clear Firmware Version : 3.12.4 Build 100910 Rel.57694n
I did a hard reset and after that, when i power on the router, it works for aprox. 15 seconds, so i can access the interface at 192.168.1.1, but after those 15 seconds it doesnt respond. The lights are on as if it was perfect, but cant go on admins interface and ping doesnt work either. I did several resets, did the 30/30/30, and clicked on reset to factory defaults on those 15 seconds but nothing happens.
I have high speed internet connection. The following image shows how my ISP provides internet connections:
ISP.jpg
I am required to put IP address in my computer network settings. This IP is used to go to login page to put username/password. It is a web based authentication(kind of captive portal you can call). Done! I am connected to the internet. Super fast!Now, I would like to share this internet connection between two computers using WR741ND router. So, what I am doing is having both these two computers connected to the router using LAN ports whereas my ISP cable to the WAN port of the router. IP settings of both the computers are set to: Obtain IP address automatically.Configuration in the router:
Logged into the router--->Network--->WAN--->Static IP--->Settings saved
I am able to connect to the internet using any of the PCs. The problem is I am unable to access the internet simultaneously using both the computers. When one computer is in the process of loading website and I try to open a website on second computer the second computer does not start loading website at all and even the first computer stops opening the website.What change do I need to make in the router configuration? Can this internet connection be shared at all?
Region : Argentina Model : TL-WR741ND Hardware Version : V4 Firmware Version : 3.13.12 ISP : Triple C
I'm trying to set up my new WR741ND router to replace the old WR541G with excctly the same cabling,ISP account etc. All seem to be working i.e. I get the PPPoE connection against the ISP and cat ping by name to Internet addresses from THE ROUTER.Also I get DHCP handing out addresses both to my desktop connection by Ethernet cable and to my laptop via Wifi.And the computers may ping the router and also connect its admin GUI.However,the computers stop at the router and can't go further.All they can go is to the router as if it doesn't route between LAN and WAN.With the 541 router everything works and as I said it has the same setup (very basic,no static routes or anything too smart).
Region : Others Model : TL-WR741ND Hardware Version : V4.20.0 Firmware Version : 3.12.11
As you can see it's a simple network, I mostly use the network to share itunes library from PC CENTRAL to the other pcs, play games like counter strike and the like, and of course share the internet connection and copy files from one to another. I have to puntualize that all the computers are in the same room.Last week my mom bought a Toshiba Satellite and I bought a TP-LINK TL-WR741ND so she can work in her room (which is pretty far if I want to make a wire connection), so I installed the WiFi but now this is how my network looks like:> The case is that:
a) I can't access my toshiba from any other computer, but the toshiba can access any other using \192.168.1.# command.
b) The PC Central's iTunes library can be played in toshiba's itunes.
c) I can't make an HomeGroup between the two pcs running w7. Actually the only one pc I want to be working in LAN with the toshiba is PC Central, but as I said earlier, PC Central can't access toshiba.
The settings in the TL-WR740N are: WAN working as Dynamic IP (got IP 192.168.1.46 submask 255.255.255.0 and gateway empty), lan 192.168.0.1, (I can't make it to be 192.168.1.#, I think that's impossible cause it always gives me an error 5008). MAC filtering and that's the only thing I changed from default settings.
Model : TL-WR741ND Hardware Version : V1 Firmware Version : ISP : EOLO
give me procedure for connecting WiFi to iPhone.The phone recognizes the router, but will not connect.No numbers, i.e. 192.168.1.1, etc are loaded No DNS loaded?
Region : Argentina Model : TL-WR741ND Hardware Version : V4 Firmware Version : 3.16.4 Build 130205 Rel.63090n ISP : Fibertel
My TL-WR741ND is about 1 year and a half old, it was working fine until about 2 weeks ago. I need to reset it, times between resets is not consistent, meaning, it can take 30 minutes, or 8 hours, but it needs to be reset. Right now, there are 2 wired connections (PS3 and Desktop PC) and 7 wireless (4 cell phones, 2 notebooks and 1 netbook). 1 of the notebooks has static IP, and it also has a VM running, with another static IP. Also some port forwarding simply stopped working (ports 80 and 1180), the rest of the ports work flawlessly, but trying to forward the port 80 and 1180 (to the 2 static ips) won't work. I already upgraded the firmware, and the problem persists, also changed the channel (from 6 to 1, and then from 1 to 11).
Installing dd-wrt/openwrt/gargoyle or anything like that, is not an option. The only reason why I bough t this router, was because I could use dd-wrt, I installed it 1 year and a half ago, and it simply sucked, the wireless bandwidth was non existent, and it was a headache. I installed it again last week, to see if it could be a solution, and I was not even able to save changes in the control panel. I need a real solution, and installing a firmware that works only on chrome is not an option (specially when I use Firefox, and I needed to install chromium just to erase dd-wrt)
Region : China Model : TL-WR741ND Hardware Version : V4 Firmware Version : ISP :
My router box and the router itself are listed as 741N. I find no reference in the forums or on the website to this model. During setup, I can ping the router from the cmd prompt, but then it fails during the Easy-Setup assistant. I need to use the Easy setup because the language is otherwise Chinese, but it fails the network test. One of the two messages it sends are "Check the Model number". Is this a possibility? Is there a work around or where can I find the proper Setup Assistant software?
Region : Argentina Model : TL-WR740N Hardware Version : V4 Firmware Version : ISP :
Region : India Model : TL-WR702N Hardware Version : V1 Firmware Version : 4.18.114 Build 130314 Rel.39604n ISP : BSNL
702N runs as repeater mode to W8968. In 702N > Maintenance > Diagnostic the ping work for Internal network but fail for external IPs. Most devices connected to 702 can access Internet fine. I have also tried Bridge and Client mode.
Ping to W8968 Code: Pinging 10.0.0.1 with 64 bytes of data: Reply from 10.0.0.1: bytes=64 time=1 TTL=64 seq=1 Ping to Internet
Code: Pinging 8.8.8.8 with 64 bytes of data: Request timed out.
Region : Argentina Model : TL-WR740N Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
Region : Hungary Model : TL-WR740N Hardware Version : V4.20.0 Firmware Version : ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
I have a DIR-825 (B) for over a year now. This morning, the wireless on it suddenly stopped working. Meaning, all my machines not longer seeing the signal from that router. If I hardwire to it, it will work fine. I have check the wireless settings and they all look fine.
Region : UnitedKingdom Model : TL-WR740N Hardware Version : V4.23 Firmware Version : TL-WR740N_V4_130104 ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
Region : Romania Model : TL-WR740N Hardware Version : V4 Firmware Version : ISP : AKTA
Network isn't working on pc or on wireless devices. I restarted, reinstalled, rebooted but isn't working. LEDs light up normally but I don't receive internet connection on devices.
Whenever I start a Cisco VPN from any machine on the network, DNS requests to the DIR-655 stop working. If I reboot the router, DNS starts working again (the VPN was left on). Why starting the Cisco VPN would freak out the router?
we just recently upgraded our router from an old model of d-link to tp link's tl-wr741nd. the wireless router was set up fine. but we noticed that we now experienced disconnection problems. our internet would just disconnect and then connect again every 5 minutes or so. but when i check the modem everything's fine. lights are on. even the lights on the modem are on. this problem never happened on our old router. is this possibly because of the N technology our new router has?
I have a Dlink Dir-615 router and a Motorola SB6120 Modem. For some reason the router suddenly says it's receiving internet access from the modem. It has worked for several months beforehand. I tried another Dlink modem and got the same results. I have my computer hooked directly to the modem hence the ability to make this post.
I have had a setup in which my four DCS-930Ls transfer picture every 15 minutes over a Dovado-router connected to a mobile broadband modem. This has worked perfectly until this last night. No pictures are transferred and upon using the test FTP function the status page just says "Testing ...." forever. I've also tested e-mailing picture without success.
I've got this router for 3 days, I configured it for Polish neostrada (TPSA), its works perfect for 3 days (until today morning). Now i cannot connect to ADSL, on info page its everything correctly. I only cannot connect (after pressing Connect page reload and nothing changed). My orgiginal Livebox from provider works (it have build in settings). I tried to reflash firmware and restore to factory settings (i tried too wizzard from CD and simple writing on info page).Wi-Fi + Ethernet works, I only cannot conect to ADSL (i tried PPPoA and PPPoE, all settings what my provider has on his page).
I am trying to set up a Tenda 150mbps wireless Ap/Router.Im trying to set it up to use it as a range extender.I followed all the directions. I put it in wisp mode. It doesnt seem to be communicating with my Tenda wireless router. It only is showing up as its own connection. so I cant even get on the internet.
Region : UnitedStates Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.1 ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : India Model : TL-WR740N Hardware Version : Not Clear ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
Yesterday my wireless internet just appeared to stop working completely, it has always worked fine up unti now!I have checked all the usual issues, it is nothing to do with my router as i can use other laptops/desktops to access the internet fine.I am using a Pavillion DV6-1215sa which has a Atheros AR9285 802.11b/g WiFi Adapter.It has full strenght but just says Limited Connectivity, so it is picking up the wireless network but wont actually let me connect to the internet via it.
I am able to access the internet when i hard wire the ethernet cable into my laptop, but the just wont work for wireless.I have tried lots of different suggestions so far, but still cannot access the internet.
i've one of my 3500 that when finish to download the os, the front led stop working. During the power on and all the test the led is flashing in various colors pretty ipnotizing :-) When it bacame operative, the led stops. If i issue the test led flashing console command it works.
I'm having problems with the wireless button after I took my laptop apart to clean. The wireless button won't switch on at all and doesn't light up. When I press fn f8 nothing happens. I'm not sure what I've done. The wires are correctly in place as far as I can tell. I've tried the following things:Uninstalling the adapter in device manager and rebooting /Checked adapter is listed as working properly /Do a system restore /Check BIOS
I recently built a new computer and it runs a wired connection. I was having problems with dns dropping.until i set static ip and dns. But now whenever my computer is on my router doesn't broadcast a wireless signal and none of my devices can connect to wireless until I turn off my computer. The router is a linksys wrt54g2
Three nights ago, around 9:30 P.M PST, my wireless connection to my router began constantly dropping every few seconds/minutes. This happens to all of my wireless devices only while I am in my bedroom, nowhere else. In every other room, my connection is stable.
My dlink dir 628 wireless router suddenly stopped working yesterday. If I plug the ethernet cable directly into my computer and the internet works. I see the wireless profile in the options for the wireless internet, but when I try to connect, it is unable to do so.
I've tried resetting the router (using the button on the device) witand reinstalling the router (using the CD), but still not working. Also have tried turning off the modem, router, and restarting my computer.
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit - All lights lit - All lights off - Power and my PC's slot number lit - etc
After an hour on the phone with the Linxys support people I'm feeling like I've been scammed.I have a 2 year old, almost to the day, Linxys Wireless-N Broadband Router, model # WRT160NVZ, which decided to stop working today. I contacted Linxys support and was told since it is 2 years old it's no longer under warranty, ok. If I choose I can pay for a service call and the tech may be able to fix the router, no guarantee. I had another option to purchase a service plan but again no guarantee repairing the router. My third option was to purchase a brand new wireless router for a discounted price, if I chose this option the tech would attempt to repair the router at no charge. I expressed my concern that it would take a few days to receive the new router and what would I do while waiting. I was then assured the router I have now could be repaired and would be able to hold me over until I received the new router.So I chose the 3rd option purchasing a M20 wireless router to be shipped to me within 3 days. After providing my credit card number and billing/shipping address the technician was now able to work with me in trying to repair the current router. He had me access the Linxys website, he instructed me in resetting the router and resetting the settings for it on the website and PRESTO, my 2 year old router now works again.but feel that this is a scam, programmed in the router to occur within 2 years of purchasing where the settings entered no longer work but once changed works perfectly well.
