I've got this router for 3 days, I configured it for Polish neostrada (TPSA), its works perfect for 3 days (until today morning). Now i cannot connect to ADSL, on info page its everything correctly. I only cannot connect (after pressing Connect page reload and nothing changed). My orgiginal Livebox from provider works (it have build in settings). I tried to reflash firmware and restore to factory settings (i tried too wizzard from CD and simple writing on info page).Wi-Fi + Ethernet works, I only cannot conect to ADSL (i tried PPPoA and PPPoE, all settings what my provider has on his page).
I got my WAG120N like 5 months back. Last night it started to disconnect randomly like at 5 - 10minute intervals.... The connection to the internet connects and then disconnects within 5 seconds. I've tried resetting, firmware upgrading, restoring settings and all that with no success. (I'm referring to the wired connection used for my PC and not WiFi)
Region : Others Model : TL-WR741ND Hardware Version : Not Clear Firmware Version : ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
I just installed the X2000 and managed to get my Win7 Home Premium to connected to the Internet and also one wireless device. I previously had just a modem. Sometimes, when my PC is up and running, I want to disconnect it from the Internet and later connect again. There is an icon on the lower right of my toolbar which, with my old modem, allowed me to connect and disconnect but it seems to know only about the old modem. Basically it operated by starting the sequence: All Control Panel Items>Network Connections>Broadband Connection. Now this function does work; it tries to connect (through "WAN Miniport (PPPOE)") and gets "Error 651: The modem (or other connecting device) has reported an error". Can you tell me what where is the program that seems to start the Internet connection for the X2000 and if I can change parameters for the Win7 "Broadband Connection" to use the X2000? Perhaps the parameter "Connect on Demand" in the "Basic Setup" of the X2000 is involved?
Well, I have a WRT120N Router for 11 months to now. I never had a problem with the Router, but since 2 days ago, It didnt connect to the internet.
My network is: Internet > Cable Modem > WRT120N > Computers
As I said, the problem is that the Router doesnt has Internet Connection.
Things to take in consideration: The Cable MODEM ISN'T the problem Because if i connect the modem directly to a computer, I have Internet connection without problems.I Diconnected and Connected both Modem and Router in several ways and several times, and it doesnt work.I also tryed clonning my PCs MAC address to the Router and it was the same.The Router Indeed receives the External IP Address from the Modem, and also, it changes if i restart the modem (as my ISP IP is DHCP). But there is NO internet conection.The Router had the 1.0.05 Firmware, and i upgraded to 1.0.06, and the problem persists. Another thing to take in account is that if I turn off my modem and the I turn it On, sometimes, the router receives Internet connection, but in matter of Seconds (minutes as much), the internet connection falls.
This is NOT an ISP problem, because as I said, if I connect the Modem Directly to any PC, i have a perfectly normal Internet Connection, And also, I called my ISP and they Said me that there werent any problem on their network.
I have also tryed with the "Router Dianostics" (the Ping and Traceroute options that are in the Router's Webend and also, no conection. So its NOT a Cables problem.
I have a Linksys E1000 router just upgrade to the latest 2.1.0.2 firmware...I have a PPPoE connection which used to run smoothly on the router..however off late...suddenly the router stopped connecting..it always shows "connecting" in the status tab of the router page...and eventually says failed to obtain IP address...however when I attach the cable directly into my PC it works just fine.I also had a word with my internet provider...he's kept the MAC open (or something like that) so he said that isn't the issue and he keeps saying there must be some issue with the router. However, occasionally the router DOES connect for half hour or so and then just refuses to connect again !..
I have this new problem, when I start my computer its connect fine to the internet, after a while its stop and lag after that but the modem is working fine and even with my laptop works also fine I've use HiJackThis and I got this:Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 09:57:27 م, on 04/01/11 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: NormalRunning processes:[code]......
I have a touch screen packard bell comp and all of a sudden i cant connect at all to the wireless router yet we can connect to the router with ipod and phones, does this mean there is summat wrong with my computer? its only two months old
For whatever reason, as of Tuesday afternoon my laptop can no longer connect to wired internet. I am a college student (NYU), so I cannot access a modem or router myself. I have tried:
-Plugging my cord into another jack in my dorm room
-Using my roommate's ethernet cord
-Taking my cord and laptop to different areas on campus (library, other dorms, etc) that use different wired networks, and attempted connection there Worth noting is that I can still connect to wireless internet just fine (however, my dorm does not have wireless, making things very difficult for me).My ethernet adapter is a Realtek PCIe GBE Family Controller. It was just updated today, in hopes that maybe it was a driver issue (Prior, it was a Realtek 8168C/8111C, whatever that means). All drivers have green checks next to them and appear to be working. Here is my IPConfig info:
I am running Windows XP Service Pack 3. My laptop is a custom-built CyberPower PC. I have done a Malwarebytes Scan,SuperAntiSpyware Scan, and Avast Anti-Virus scan, and have turned up no malware or viruses.
my net is connecting so late after a sudden hang in windows, and sometimes showing Error 718..It has become very often...I asked my friends (same connection), they are not having any problem from the ISP... what's wrong? :/ Few minutes ago, it was showing error 718, i had to restart, and then it connected (still slowly).
I've been using my DCS-930L happily for the last month. Today, it suddenly stopped working. I haven't made any changes to my network or any configurations in about 2 weeks, during which the camera has worked fine locally as well as remotely. Now, if I unplug/plug it back in, the camera will immediately connect. However, after a period of time, it's no longer accessible, even from my local network. When I try to log-in to the camera or view it, it cannot be found or connected to. So it doesn't seem to be any of my configuration, but something that's intermittent or happens after awhile.
For the past few months my cable modem has been rebooting (Power light stays on the rest turn off). I have replaced the modem and have had two technicians out here to no avail. The resets happen often during heavy use.The only errors that seem to happen frequently while this occurs are..
5/17/2012 20:33120207004Configuration File CVC Validation Failure 5/17/2012 21:54200005003Started Unicast Maintenance Ranging - No Response received - T3 time-out 5/17/2012 21:54200006003Unicast Maintenance Ranging attempted - No response - Retries exhausted 5/17/2012 21:54180002003UCD invalid or channel unusable 5/17/2012 21:54140206003DCC aborted unable to communicate on new upstream channel
I normally have fairly speedy cable internet (12 MBPS) and it has never caused me any issues in the past. My ISP is a company called Ygnition (not the best). My problem is as follows: I was using my internet on Tuesday to play an online game (SW:TOR) and I walked away from my computer for about 30 minutes, and when I returned I had been disconnected from the game and the internet appeared to be non-functional. I've now discovered that the internet IS CONNECTED but it is INCREDIBLY slow. It takes at least ten minutes to load the google homepage and websites like speedtest.net are unusable. I obviously cannot use the internet with any efficiency, much less log into an online game.
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
Two years ago I bought a WAG160N for modem (ADSL) and router functionality. I consider to buy a pure router (E3000 or E4200) to connect to the WAG160N and use that one purely as the modem. How and what should I configure/disable on my WAG160N?
Model: Linksys CM100 Cable Modem, purchased December 2010
Modem goes dead immediately after 3rd light goes solid. All lights go out and the modem stops functioning completely. Using the reset button gives no response, the modem stays dead. Upon unplugging and plugging it back in, the modem turns back on and cycles through the lights, only to die out once again.I was initially able to get it to stay alive by starting it with the Ethernet cable disconnected then plugging it in once the modem had connected, which I found odd. After a relatively short period, say 20 minutes, the modem would randomly die out again. However even that has since stopped working.
I have recently bought a WAG320N modem Gigabite router to substitute the modem router supplied by the internet service provider (in theory less performant).
Formerly I have a wireless router Zyxel (MOD. P660HW-D1). The main computer is wired (connected trough ethernet), I have also a NAS device (WD mybook world 1TB with Twonky as server) wired and a third wired connection for the above mentioned PLK 300. The PLK 300 (4 Inputs and one output) is used to connect a TV (Sony BRAVIA) a Bluray (SONY) a PS3 (Sony) and a multimedia HD (DVICO). All this was working properly. I have internet access from TV, PS3,... I was able to run videos, photos,... stored in the NAS from TV,....
I decided to change for improving the transfer speed and to allow a better wireless connection (I have initially coverage problems, but because I only use the wireless rarely...).Initially I bought a Linksys E 3000 (I thought it was possible to connect it directly to internet and not trough a modem. I asked to several people and in several shops but no one told me this was not possible). That was my first failure: I would like to suggest the liknsys people to clearly explain this on the product sheet to avoid that not very well informed people like me commit the same error.
Then I chaged the E3000 by the WAG320N. I connect the new modem-router like the former (Zyxel). No room for big errors, just the power, DSL line and ethernet cables. It works for the PC and the NAS but the PLC (PLK300) do not appears to work. Several tries later (including plugin the PLK on the line 1 input of the router it is shown on the network map but do not work. I do not have access to the internet nor to the NAS contents form TV,....
I go back to the former router and everything works again in the simplest way (I have internet access form TV,...) except the Twonky access to the NAS from TV ¿?. I do not know exactly what I have changed,...)
I have 2504 wlc, 1142n ap's and a windows radius server.Users have figured out that they can connect their kindles to the wireless by using there network login credentials. How can I stop this? Change authentication from user or computer to just computer?
I have bought Cisco WAG120N modem+router weeks ago, and until now I have trouble with connecting it to my android phone with wi-fi, every time I try to do it keep trying to connect and after that I get a massage connection lost in my PC, then I have to restart modem-router agin to get the internet connection,
previously I had my ISP provided unbranded one and it worked fine, since Cisco have good name I bought this and now I was totally disappointed,
even the Internet connection stop without any reason and I have to do restart process.
Region : Philippines Model : TL-MR3220 Hardware Version : V1 Firmware Version : ISP : Smart Bro
Today my router stops working. There is no internet on wifi even on lan. I thought my ISP is the problem but when I plugged in the wan cable to my laptop there's an internet. I tried to switch off the router and when I turned it on, there's an internet for about 15 seconds then after that there's no internet again. I also restore the router to its default setting but it doesn't solve the problem. This is the first time it happens to my router. I'm not using static ip address
Yesterday I was on my cousin's computer, and we had to remove the ethernet cord to connect it to mine as my wireless adapter wasn't cooperating with his internet. This was all fine and dandy until we had to plug the ethernet cord back into his computer. It locks everything up. If you try to open a program, it won't open. If a program is already open when the cord is plugged in, it stops responding within 15 seconds.I called my brother, and he suggested I run a virus scan via Microsoft Security Essentials and MalwareBytes, which I did. MalwareBytes found 5 problems, MSE found 1 additional one. They have all been removed, however this problem still persists. If you try to start the computer with the ethernet cord plugged in, it will allow him to put in his password, it will say welcome for about 3-5 minutes, then the screen will go black. The mouse is visible, doing it's motion to indicate that it's loading something, but it never achieves anything.
I have a Linksys X5000 hooked up with my home pc. The internet I get is free though the private school's network I work at (across the street) through a LAN. With a bit of wrestling I got my desktop to connect with the internet through the Linksys like an ethernet switch.I can't get my wireless devices to connect with the internet without logging in as a guest, which is annoying to do every time, especially through my iPod. They will gain access to my network, but not the internet.
Since this is a school network, my IT guy gave me a static IP address to speed up up/downloads by disabling DHCP. Every time I try to do that I get a message that "the page at 192.168.1.1 says the value can't be equal." OK, so I try to change my router's IP to 192.168.1.2 and...no luck, same message. I love working with hardware, but networking is beyond me. I don't think I can log into the guest screen in my own house any more! I am getting a new tablet in 2 days and this just won't do.
A few weeks ago my internet speed suddenly became slow. Not so slow you can’t do anything without having to wait half an hour, but significantly slower than usual, and it also has occasional drop-outs. It can’t be an issue with the computers connecting to the router, which it’s doing fine as I can access my router’s setting though the IP address, but with the router connecting to the internet.
All of a sudden, the router's internal ethernet switch has started to get very slow at connecting to local machines. I can observe the connection fading in and out on each connected machine for up to half an hour until it gets stable. None of the settings have been changed lately.When I use WI-FI, the problem doesn't occur.
The last time I had to reconfigure the connections it took me hours!My son had to wipe his desktop clean and reinstall everything. Now when he tried to connect to the internet we can't get a connection at all. My desktop is still working fine as well as the wireless laptops.What do we have to do to get him reconnected?
I want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
I have recently purchased a WAG320N. It is working perfectly, connecting 3 PC's, 2 Xbox 360's and a laptop to the internet and each other.
However as all media files are stored on one PC I was thinking about getting a external USB drive and connecting this to the router and use that as the media server, this would save a PC having to be on all the time.
I use one of the xboxes as a media player as well, streaming movies and music. Will the 360 pick up the media server and be able to stream from there?I can not find anything on the internet as well about the possibilities for this.
How can i connect my window xp with window 7? "I have already done all settings like workgroup setting, ip location but my window 7 lappi is again showing yellow point."
