Whenever I start a Cisco VPN from any machine on the network, DNS requests to the DIR-655 stop working. If I reboot the router, DNS starts working again (the VPN was left on). Why starting the Cisco VPN would freak out the router?
View 3 RepliesRegion : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
Router: Linksys Wireless-G Model: WRT54G v8
Wireless Adapter: Belkin model F7D1101 v1
I have two computers in my house, one is set up directly to the modem/router and the other (in my room) is set up wireless using that belkin adapter above.
Everything has always worked perfectly, but two days ago things went haywire. If my PC connects to the wireless, then it makes the router stop working for the other computer and any wireless devices I have. As long as I don't have my PC connected, then things run smoothly and there are no problems, so it's definitely stemming from my PC?
I thought it might have been the router at first, so I switched it out and it worked fine for over 24 hours, but then the problem came back.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Sunako-PC
Primary Dns Suffix . . . . . . . :
[Code].....
I have installed VM ware v Sphere Enterprise Plus 5.0.0 and created a VM using an OVA file with LMS 4.1 running in Linux. It was working good since 3 weeks ago and I was adding snmp server configuration in all my devices (routers/switches) and suddenly one day DCR Server process stop working. I was trying the following actions:
1.- dmgtd stop -> to stop daemons
2.- dmgtd start -> to start again the daemons
And the DCR Server does n´t start up automatic.
Then I try this:
1.- pdexe DCR Server
And show this message:
[CPLMSCOL01/root-ade ~]# pd exec DCR Server
ERROR:Get reply from server failed:
and don´t start up the DCR Server.
I have setup a Cisco SR520W and everything appears to be working. After a few hours, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device.
If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my the modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again.
Here is my config file:
Building configuration...
Current configuration : 17830 bytes!version 12.4no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice
[Code].....
i've one of my 3500 that when finish to download the os, the front led stop working. During the power on and all the test the led is flashing in various colors pretty ipnotizing :-) When it bacame operative, the led stops. If i issue the test led flashing console command it works.
View 1 Replies View RelatedYesterday my wireless internet just appeared to stop working completely, it has always worked fine up unti now!I have checked all the usual issues, it is nothing to do with my router as i can use other laptops/desktops to access the internet fine.I am using a Pavillion DV6-1215sa which has a Atheros AR9285 802.11b/g WiFi Adapter.It has full strenght but just says Limited Connectivity, so it is picking up the wireless network but wont actually let me connect to the internet via it.
I am able to access the internet when i hard wire the ethernet cable into my laptop, but the just wont work for wireless.I have tried lots of different suggestions so far, but still cannot access the internet.
I know about recomendation to update a system software! Here is my software version and rdp plug-in version: asa843-k8.bin, rdp-plugin.120424.I also tried to use previous version of rdp plug-ins, but connection through RDP still not work normally! 90 percent of the attempts to give a black screen.
View 1 Replies View Relatedall of a sudden my internet stop working and its now saying limited access ive tried all of thoose ipconfig things and none of them worked
View 19 Replies View RelatedI'm trying to get a static IP because I'm hosting a team fortress 2 server.So on windows, I made my internal IP static and that worked.On my router(cisco EPC 3925) you can go to administration ,then management and it says connection mode: DHCP which you can change to Static IP. When you change it to static IP it askes you:[CODE]
View 5 Replies View RelatedOnce again I'm stuck to tethering on my phone due to my router deciding to call it quits for the random moment. I cannot access its control panel, the network just goes kaput. Given that I don't have access to the router since it's part of a double house (the side I'm not on of course), this is getting beyond irritating to reboot it when this happens as that is the only way to fix it. The connections are even wired, too. What kind of money does it take to get a router that is going to STAY on and just work? I'm ready to dump some serious cash into this at this point because this happens at least twice a week anymore. I just want a router that works. It needs to be wireless as my neighbor does use his kindle on it every once and a while.
View 4 Replies View RelatedI'll be downloading off of newsgroups and be pulling 3-4 MB/sec, no problems. My downloads are charted so I can see my speed never drops at all.but my web browsing will just STOP, for ~30 seconds. I'll have multiple tabs just STOP and crap out, while my downloads run fine. This also happens when I'm not downloading, so I know it's not a bandwidth issue,i assumed it was a router issue until I replaced my router and am getting the same issue.
View 1 Replies View RelatedI've dell inspiron n5110 with dell wireless 1702 802.11b/g/n sometimes working sometimes not working and work if i restart the machine .
while i'm working on laptop the net does work and once i try to find the wifi ssid i can't see any of them and written no network available.
i do lot's of thing and the problem still
1. update the drive
2.change the properties of wirelss adapter in power managment
I recently built a new computer and it runs a wired connection. I was having problems with dns dropping.until i set static ip and dns. But now whenever my computer is on my router doesn't broadcast a wireless signal and none of my devices can connect to wireless until I turn off my computer. The router is a linksys wrt54g2
View 4 Replies View RelatedI am using a dell Vostro 3550 series, window 7 which I recently upgraded it to 64 bit from 32 bit and after that my Intel WiFi utility stop working. I can create the WiFi hot spot and connect my phones and laptops but its not sharing the internet. I've checked the "share my internet" button too but still then its the same result.
View 22 Replies View RelatedAfter an hour on the phone with the Linxys support people I'm feeling like I've been scammed.I have a 2 year old, almost to the day, Linxys Wireless-N Broadband Router, model # WRT160NVZ, which decided to stop working today. I contacted Linxys support and was told since it is 2 years old it's no longer under warranty, ok. If I choose I can pay for a service call and the tech may be able to fix the router, no guarantee. I had another option to purchase a service plan but again no guarantee repairing the router. My third option was to purchase a brand new wireless router for a discounted price, if I chose this option the tech would attempt to repair the router at no charge. I expressed my concern that it would take a few days to receive the new router and what would I do while waiting. I was then assured the router I have now could be repaired and would be able to hold me over until I received the new router.So I chose the 3rd option purchasing a M20 wireless router to be shipped to me within 3 days. After providing my credit card number and billing/shipping address the technician was now able to work with me in trying to repair the current router. He had me access the Linxys website, he instructed me in resetting the router and resetting the settings for it on the website and PRESTO, my 2 year old router now works again.but feel that this is a scam, programmed in the router to occur within 2 years of purchasing where the settings entered no longer work but once changed works perfectly well.
View 6 Replies View RelatedPerhaps once a week my ethernet port stops working. That is, it is still displayed as 'working properly' in the device management screen, but it is unable to connect to dns. System restore does not solve this problem. plugging the ethernet cable in and out (10 times) does not solve this problem. Modem reset does not solve this problem either. I decided that perhaps ethernet controller is faulty, or perhaps the ethernet port in itself- so I bought a 'usb to ethernet' adaptor and surprisingly the internet connection problem persisted (during the instances when my laptop ethernet port had problems connecting to DNS, the adaptor was also unable to connect to internet).
What does solve this problem is this: I have another notebook - I plug the ethernet cable into that computer. Obviously, internet works without any problems with my second notebook. After that, I plug the ethernet cable back into the laptop which is now unable to connect to DNS. Quite often the Not being able to connect to DNS issue still remains the first time I do this, so I have to connect ethernet cable back into my second notebook and then plug it back into the notebook with a connectivity problem. After I do this 2 or 3 times, my windows 7 laptop is finally able to connect to internet.
I've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies View RelatedI received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.
View 1 Replies View RelatedFew days ago the wireless in my son's Dell Inspiron 620 went bad. It does connect to my old router (WEP), but speed is terrible and connection goes bad after some time. I can also see my modern router and enter the key successfully (WPA2), but it won't connect. Connection to both routers went well for months before, and still goes well from all other devices in the house.
I read the issue with McAfee that was posted late August and followed the steps. Connection in safe mode didn't work. Then I removed McAfee from the PC, no difference. Then I restored the PC to a couple of days before the issues began, removed McAfee again (as it came back through the restore), no difference.
I reinstalled the drivers of the Dell wireless card, no difference.
I'm having problems connecting to the Internet using the wireless adaptor - it will connect initially but the connection is very very slow and then will eventually drop out and stop working.When I connect using an Ethernet cable, there are no problems whatsoever so I know it is not a service provider issue.I have updated the BIOS to A11 and all drivers are up to date. The wireless adaptor is Intel Centrino Wireless-N 1030. [code]
View 3 Replies View RelatedMy 3rd day with my newly bought All-In-One 2320 i7, 2TB, 8MB...This is the seond issue I found on this machine:Browse iplayer page, choose a video to watch, but...when viewing video from iplayer in IE, browser stop working. The whole page freeze.Same thing happened on youtube.
Things I have tried:
- Test it in Firefox. Same result. So bad.
- Update my flash player, java,..etc.
What else can I do? So dissapointed. I have promissed my son to show him the cbb animation cartoon on my new computer (big screen)..
We have a router (7206) which connected to client device in /30 IP segment, but this device is a switch which connected to many more devices. Doing packet capture on our router interface unravel many ARP requests which comes from the client switch.Is there any feature or command which we can stop this?
View 3 Replies View RelatedHow do i stop a Wireless device from connecting to the router? i attempted to find an answer myself and failed
View 1 Replies View Relatedi can detect the IP of DDOS attacks and if there's a simple way to prevent it. I've heard different suggestions from blocking incoming ping requests to blocking specific IP ranges
running 2.03 firmware
I have the DIR-655 Hardware version B1, Firmware version 2.00NA and everything has been working fine for about 3 months. Lately the internet connection to all the computers would just stop. All the computers are connected to the router and the router is connected to the cable modem and their is no indication of a problem. The lights are all on and the router status shows the cable status as connected and the network status as established. I can't open any webpages, or all the ping would time out. It happens on all device, Windows Vista/7 PC, Mac computer, Linux laptop, and iPhone/ iPad. The problem gets fixed when I reset the router or just wait about 5-10 minutes and the problem goes away. That normally isn't a problem, but it's starting to happen twice a day now and it is really really annoying when I'm playing games. I tried the FAQ and searching the forums, but in vain.
View 7 Replies View RelatedRegion : Australia
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I have TL-WR740N router. I dont know how to stop and start wifi signals.
I live in a Townhome complex so inSSIDer displays a lot of wireless activity. I have noticed that many of the routers channels are listed as 6 + 2, 4 + 1, etc., while show only a single channel. I have been able to "temporarily" replicate this by setting the Channel Width on my DIR-655, by setting channel width to auto, and when I am successful it displays a speed of 300, both in my task bar and in inSSIDer. However, that is usually short lived and the channel for my router reverts back to a single channel and the displayed speed drops to 130 or 144. My neighbor's Netgear is rock solid at displaying dual channels. Well, that and besting my signal strength. :-)
I have the router manually to channel 8 because none of the routers, judged by their displayed strength, use it.So, I guess my question is; how do I stop my DIR-655 from dropping back to using a single channel, which I interpret 20MHz, even though it is set on auto?
I recently purchased a dir 655 router and it works fine but in after a while of using it, the wifi signal will stop broadcasting my other computers still work with the internet that are hard wired but the ones im using through the wifi signal will loose connection. So my fix has been unplugging the router and plugging it back in then it will broadcast my wifi again. I tryed leaving it plugged in and refreshing and rebooting my computers but that wont fix it until i disconnect the router and plug it back.
View 14 Replies View RelatedI have 3 cameras. all had the problem that after a while motion detection would be triggered continuously for no reason at all. With 2 of them I managed to fix it with a firware update, but no luck with the 3rd one. I even tried several different firmware versions.) it starts to record continuously after abt 24-48 hrs & i have to reboot to get it to stop.
View 1 Replies View Relatedwrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 Replies View RelatedMy younger brother uses IDM to download files and it slows my Internet down to a crawl. I've tried reasoning with him but its not getting through to him. Is there any way I can use my router (bcz only I have access to it) to limit IDM?
View 5 Replies View RelatedI recently switched from a DSL ISP (Earthlink, Zyxel modem configured as a bridge, pppoE connect) to a cable ISP (Comcast, Arris cable modem, dhcp connect). Basically PC --> DIR615-->Cable modem-->Internets. With the old DSL the Internet activity LED (green, looks triangular) on the DIR615 blinked only when internet activity occurred. With the new Comcast connection it blinks non-stop about 5 times a second! Even if the PC is turned off it blinks. It stops blinking if I disconnect the ethernet cable between router and modem. The connection itself is fine, but if the DIR615 is doing something it should not be doing it might slow the connection down a bit, (or burn something out prematurely?)FYI, the Arris cable modem does not seem to be a router. It takes a cable connection from outside and provides a single ethernet cable and 2 (voice) telephone cables to the house.
View 1 Replies View Related