wrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 RepliesI use a WRT54G wireless router connected to Mac. All of a sudden, I became unable to access certain websites on my iMac, such as Facebook and Apple homepages. But i can access Yahoo website. I tried resetting my linksys setup but it doesnt solve the problem. When i access my iphone via wifi at home, i am also unable to go into app store, facebook app, and emails with images won't load. I also cannot link my iphone to itunes on my iMac. What happens on my computer when I surf the internet is that the page just loads halfway and stop "responding". But my imac airport says that my internet connection is fine, however my access has become very "restricted".
View 1 Replies View Relatedhow to setup WRT54G for blocking all unwanted websites for users. When tried to configure Website under Access Restrictions tba, it accepts. However it doesn't block.
View 1 Replies View RelatedI'd like to block all websites except a handful. how can i do this?
linksys wrt54g
I've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies View RelatedI received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.
View 1 Replies View RelatedI upgraded my wrt54g v.2 with a firmware for wrt54gl and now, the power light is continuous blinking and I can't access via web to the device.I tried to reset it and replace the firmware without success.
View 3 Replies View RelatedI recently have been reading into QOS and have been fiddling with it on my Linksys WRT54G router. But there are a few things that seem limiting (at least on this version) so I have some questions.I live in a house with three other roommates all sharing the same internet connection. We don't have a bandwidth limit, so I don't care how much they're downloading. When I want to watch Netflix when they're all on the internet however, either my movies will come up in low quality, or will be interrupted.Under the Device Priority I put in my MAC address and set my priority to high. My first question is, what is the priority of a device that is not listed at all? There's only room for two devices so I can't put all three of my roommates in. I would assume their priority would automatically be the lowest.
I wanted to set certain common ports to be at a high priority. So far I just have port 53 for DNS entered with the highest priority, while my computer is set to high. Would this mean any computer making a DNS request would have a higher priority than my computer making a non-DNS query? I would like DNS to be a higher priority than myself streaming video.Finally, are there are ports that streaming video commonly use? I know there are ports for Netflix but I was also thinking of other Flash/HTML5 videos I might come across. Or do they tend to just use port 80?
My roommate and people he invites over keep downloading torrents from public sites and I've gotten 3 emails from Comcast so far. I've talked to him, but I want to make it impossible for him to be able to download them...
I have a Linksys WRT54G router.
I've made 6 internet access policies in the Access Restrictions settings of my router, but for some reason only the 1st policty works. I had 'torrent' as a keyword on the first policy, and when I googled most popular torrent sites it wouldn't let me... so I took 'torrent' off the keyword list and did my google search, and after I wrote down the 40 most popular public torrent sites, I added torrent back as a keyword for website blocking and saved it, but now it doesn't work for some reason. So at first it worked, then I took it off so I could search using the keyword torrent, then I added it back again and saved it and now it doesn't work.
1st policy works (besides the torrent keyword). I have all my policies enabled, have set ip ranges from 0-254 for all of them, and gave them each a name.
How come only the first policy works, and how come all the keywords in the first policy work except one after I deleted it and then re-added it?
Running Comcast Business Class in my restaurant. I have a Mac Pro PowerPC G5 tower running OSX: 10.5.8. The Comcast guy hooked everything up along with the WRT54g i found in the basement (previous owner). Everything worked well, he programed the router through his internet pad; never touched my Mac. All of a sudden my power outlet in which my modem and router are connected reset themselves. I reset them back on, however, my router Never worked again. My mac is directly connected to my modem, not router. I have it hooked up on LAN #4 (light turns on), however, after the outlet reset, the router wont even show up on my Modem's LAN. I cant open it open it on my browser, 192.168.0.1, or 1.1. I try the 30-30-30 reset, nothing. While looking for my own remedy, i think i downloaded the new firmware to my mac, nothing happened.
View 1 Replies View RelatedLinksys WRT54G wireless router is not working on my laptop. It is telling me this statement: ”The settings saved on this computer for the network do not match the requirements of the network.”
View 1 Replies View RelatedI have tried everything I know. My router is about 4 years old, so it may be time for a new one, but it has been working great, then it just stopped.
View 2 Replies View RelatedLast night, my wireless router suddenly stopped working. I no longer saw my router listed in my available wireless networks, and neither could my girlfriend from her computer. I unplugged the router to see if one of the available networks had disappeared in case my router had somehow been reset, and nothing changed so my computer isnt even seeing my router. Right now, I am wired through the router so I know the router works, but the wireless part doesnt for some reason. I was looking up stuff in the FAQ, and think the firmware is corrupted since the LEDs are all blinking. I was trying to update my firmware following the instructions I found using tftp.exe, however it failed. One problem is that I can't set up a static IP address since I need to access the web-based utility to check my DNS server but I cannot access the web-based utility anymore (maybe cause of the corrupted firmware?). On a related note, there is someone else in my building using a linksys with the default network name of linksys. I had changed my network's name and security-protected it, though that is all likely gone now since I tried to reset the router. My question is what will the network name of my router be if I saw it since "linksys" is already taken. or will there just be two of them?
View 1 Replies View RelatedI have WRT54G connected to a cable modem for internet service. Came home at lunch yesterday and all was working fine. Came home after work last night and couldn't connect to the internet. Called Charter cable this morning and their troubleshooting showed I can connect to the internet fine if I bypass the router, so the issue must be with the router (and of course not their problem...). How do I trouble shoot this? I've tried powering down the router and releasing and renewing IP addresses but it hasn't worked.
View 9 Replies View RelatedI have a Lynksys WRT54G wireless router. It works just fine until I try to put a password on it. I go through the basic steps, it talkes all my information and tells me everything is good. I try to sign on the internet and it tells me my password is invalid....and YES Im sure its the right password I entered. I went to http://192.168.1.1/wireless.htm and did all the necessary instructions, and still, it doesn't work. I can change my network name and it works. As long as I leave it unprotected, everything works fine, but when I add the password, it tells me its invalid. I even used 123456 so as to make sure it was the right one.
View 5 Replies View RelatedLast night, my wireless router suddenly stopped working. I no longer saw my router listed in my available wireless networks, and neither could my girlfriend from her computer. I unplugged the router to see if one of the available networks had disappeared in case my router had somehow been reset, and nothing changed so my computer isnt even seeing my router. Right now, I am wired through the router so I know the router works, but the wireless part doesnt for some reason. I was looking up stuff in the FAQ, and think the firmware is corrupted since the LEDs are all blinking. I was trying to update my firmware following the instructions I found using tftp.exe, however it failed. One problem is that I can't set up a static IP address since I need to access the web-based utility to check my DNS server but I cannot access the web-based utility anymore (maybe cause of the corrupted firmware?). On a related note, there is someone else in my building using a linksys with the default network name of linksys. I had changed my network's name and security-protected it, though that is all likely gone now since I tried to reset the router. My question is what will the network name of my router be if I saw it since "linksys" is already taken. or will there just be two of them?
View 3 Replies View RelatedI am running a Linksys Wireless G 2.4 GHz Broadband Router Model WRT54G. I am unable to open any ports. I upgraded to the latest firmware yesterday but still am unable to open any ports. I even turned off my Symantec Internet Security Suite Firewall but still am unable to open any ports.
View 1 Replies View RelatedI went online with a tech real quick before I found I beyond complimentary tech support. They say my router is working like a switch. I cannot get any wireless access and to the three direct connections to the router only one is working. The lights are constantly blinking, with the power light blinking every so often
View 1 Replies View RelatedI have the Linksys WRT54G And it was working fine for years! Then today my computer shut down and when I turned it back on there was a connection but my computer was not responding to any commands. The icon shows full connectivity excellent connection. When I try to go to a web page it shows Connection Error and cannot get to any web pages.I am able to get on other wireless connections from neighbors but not mine. I have gone thru different directions on here and I am not technical and don't understand what is being said. I try to go to 192.168.1.1 and it asks for a password which I don't have. I have tried everything such as password and admin and get nothing.I am able to get my ip address and default gateway address and don't know the next step.
View 1 Replies View RelatedI have wirless router WRT54G ver.2. and I had firmware 2.0 So I downloaded new firmware From Here and did exactly as in instruction.
After update went successful I unplaged my router for 30 seconds but it's not working. I mean it's flashes and everything but can't access it and it is not broadcasting. and whats most interesting, reset buttom is not working
Want can I do? can I access it with some other way and reinstall firmware?
I have 2 laptops in my home, I had no problem getting one to connect to the internet. The second one I'm having trouble connecting, I am wireless, I didn't have a problem at my old house with another laptop connecting to the internet with this router. I'm trying to save myself some money by not going through my wireless company, and end up having to get their router, which I already have their modem.
View 1 Replies View RelatedI have the WRT54G router for years and use it to provide both a wireless network for our home computers and a wired network for by internet phone that connects me to my office phone system and for my work computer and printer. Last week, the wired network stopped working. I checked the wiring and plugged my wire into all four of the ports in the back of the router with no success. I followed the troubleshooting procedure that I found and changed the MTU setting. I tried to update the firmware but the screen seemed to lock up and I was unable to complete the task.
View 9 Replies View RelatedI have had a WRT54G V3 router working successfully for a number of years now with a couple wireless PCs through a cable modem with Comcast as my ISP. All of a sudden yesterday, neither PC could access the internet. No changes had been made to the router.
I contacted Comcast and they of course had me hard-wire one of my PCs into the cable modem. That worked and I was able to access the internet. However, when I tried to put the router back in place (in either a wired or wireless fashion), I could not access the internet.
I've tried following the online Linksys troubleshooting document ion. The lights that should be lit on the router are lit. I can access the router setup web page which shows the settings still intact. I've tried going through the power sequencing to no avail. Comcast says my router is the culprit of my problem, but I don't know why it would all of a sudden stop working. My wireless printer still works so it detects a signal and my PC shows it's connected, but no internet access is possible.
What do I need to do? Are there any other diagnostic tools available? I'm out-of-warranty.
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
View 9 Replies View RelatedI recently built a new computer and it runs a wired connection. I was having problems with dns dropping.until i set static ip and dns. But now whenever my computer is on my router doesn't broadcast a wireless signal and none of my devices can connect to wireless until I turn off my computer. The router is a linksys wrt54g2
View 4 Replies View RelatedRegion : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
Since a couple of weeks I have a linksys EA6500. When I go to the device list to see which devices are online the device list is not displayig the correct data. I see devices online that are offline and also devices are offline that are at the moment online. When I try to delete a device that is offline in the list I get error 2315. I have that error in the local and cloud interface. The list has a frozen state from a particular moment.
When I reboot the router then all devices in the list have status offline and the device list stays that way. Nothing gets online anymore or will be added. When I reset the router to factory default all keeps working without problems for approximately 24 hours and after that the problem occurs again. The list freezes again and you are not able to delete a device.
I searched the forums but no one has this problem. I only can find a post that describes my problem but for them a reset worked. In my case a factory reset works also but the problem keeps coming back.
I am new to firewalls and I am trying to make mine block specific websites but so far have had no success. Here are the settings I am using in the router's admin area:
Security > Firewall > General
Active firewall
Security > Firewall > Rules
[Code].....
After an hour on the phone with the Linxys support people I'm feeling like I've been scammed.I have a 2 year old, almost to the day, Linxys Wireless-N Broadband Router, model # WRT160NVZ, which decided to stop working today. I contacted Linxys support and was told since it is 2 years old it's no longer under warranty, ok. If I choose I can pay for a service call and the tech may be able to fix the router, no guarantee. I had another option to purchase a service plan but again no guarantee repairing the router. My third option was to purchase a brand new wireless router for a discounted price, if I chose this option the tech would attempt to repair the router at no charge. I expressed my concern that it would take a few days to receive the new router and what would I do while waiting. I was then assured the router I have now could be repaired and would be able to hold me over until I received the new router.So I chose the 3rd option purchasing a M20 wireless router to be shipped to me within 3 days. After providing my credit card number and billing/shipping address the technician was now able to work with me in trying to repair the current router. He had me access the Linxys website, he instructed me in resetting the router and resetting the settings for it on the website and PRESTO, my 2 year old router now works again.but feel that this is a scam, programmed in the router to occur within 2 years of purchasing where the settings entered no longer work but once changed works perfectly well.
View 6 Replies View RelatedHow do i stop a Wireless device from connecting to the router? i attempted to find an answer myself and failed
View 1 Replies View RelatedMy linksys router wrt54g v3.1 won't allow my pioneer vsx-1021-k to connect to my pc.
When directly connected, pioneer plays airplay fine/windows added device, but through router device still shows, but no airplay. pioneer listed ip address as 192.168.1.102 when connected directly.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Professional, Service Pack 1, 64 bit
[Code]....
My problem is that we updated (yeah, right) our old router to a new TALKTALK one. Now my phone and one laptop device is connecting fine, no problem, but my old laptop that I need to go on is not liking the new connection. It's saying that it is connected but only local access is available and it says the connection is unidentified.
View 14 Replies View RelatedYesterday my wireless internet just appeared to stop working completely, it has always worked fine up unti now!I have checked all the usual issues, it is nothing to do with my router as i can use other laptops/desktops to access the internet fine.I am using a Pavillion DV6-1215sa which has a Atheros AR9285 802.11b/g WiFi Adapter.It has full strenght but just says Limited Connectivity, so it is picking up the wireless network but wont actually let me connect to the internet via it.
I am able to access the internet when i hard wire the ethernet cable into my laptop, but the just wont work for wireless.I have tried lots of different suggestions so far, but still cannot access the internet.