I received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.
View 1 Replies
The E1200 is connected to a router (BEFSR41) that is acting as DHCP server. So I have disabled the DHCP Server option on the E1200. Once configured, the wireless connection is working by unexpectedly only as guest user (I tried via PC XP, PC Win 7 and IPad) on the guest network. The problem is that once configured, the E1200 is no more reachable unless I reset it and I reconfigure it. If I try to access the IP 192.168.1.1, I get the setup page of the router (BEFSR41) and not the E1200. From another computer the IP Scan discover the E1200 as 192.168.1.103, but I am not able to reach it at that address.
View 5 Replies View RelatedI've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies View RelatedI have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.
View 4 Replies View RelatedI set up port forwarding on my router. When I go to canyouseeme.org and put in my public IP address (I can ping the IP address with no issues) and the port that I'm forwarding it says it can't hit the port.
View 2 Replies View Relatedwrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 Replies View RelatedI have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
View 1 Replies View RelatedHave a v2 E1200. Connect with PPPoE to ISP. IPv4 works fine. With firmware included on router, 2.0.01, it would receive a /64 of IPv6 from the ISP. This /64 would show up under 'status' / 'local network'. Although it did not seem to advertise this space to PC's on my network so I was unable to use it. I updated firmware to 2.0.04. Now it does not even pick up the IPv6 /64 at all.
Anyone have PPPoE and IPv6 working? Anywhere I can download 2.0.01 to try it again?
Is there a model of router that actually works with IPv6?
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.
Right now I have my computer (iMac early 2012 summer purchase) plugged directly into the wall via ethernet cable for internet access. I have only begun doing this in the past week because my E1200 wireless router has stopped working properly. I have reinstalled and reset to factory settings and set up with Cisco Connect and setup manually over the past week troubleshooting every possible way I have ever known how. My internet, obviously, is working. And when I set up the wireless network it connects properly and obtains an IP address and the lights on the back of the unit light up correspondingly and correct. But I cannot connect to the internet via the router, wirelessly or plugged directly into it. Yet when I take the internet cable and plug it straight into my computer it works.Mainly just need to know if this can be fixed or if I need to go return this unit and get a replacement. The router was purchased two months ago and has not had any issues since I first set it up until a couple of weeks ago and my phone is using up all of my cellular data plan without being connected to my wi-fi...
View 1 Replies View RelatedThe Network icon in the notification area in the bottom right hand corner of my screen will almost always look like this:Quite frequently, though, I will get an exclamation mark inside a triangle with a message instead saying No internet access (I don't have a screenshot). If I give it a few seconds, usually never more than a minute (30 seconds on average it seems), it corrects itself and gives me back internet access.
I recently built a new computer and it runs a wired connection. I was having problems with dns dropping.until i set static ip and dns. But now whenever my computer is on my router doesn't broadcast a wireless signal and none of my devices can connect to wireless until I turn off my computer. The router is a linksys wrt54g2
View 4 Replies View RelatedAfter an hour on the phone with the Linxys support people I'm feeling like I've been scammed.I have a 2 year old, almost to the day, Linxys Wireless-N Broadband Router, model # WRT160NVZ, which decided to stop working today. I contacted Linxys support and was told since it is 2 years old it's no longer under warranty, ok. If I choose I can pay for a service call and the tech may be able to fix the router, no guarantee. I had another option to purchase a service plan but again no guarantee repairing the router. My third option was to purchase a brand new wireless router for a discounted price, if I chose this option the tech would attempt to repair the router at no charge. I expressed my concern that it would take a few days to receive the new router and what would I do while waiting. I was then assured the router I have now could be repaired and would be able to hold me over until I received the new router.So I chose the 3rd option purchasing a M20 wireless router to be shipped to me within 3 days. After providing my credit card number and billing/shipping address the technician was now able to work with me in trying to repair the current router. He had me access the Linxys website, he instructed me in resetting the router and resetting the settings for it on the website and PRESTO, my 2 year old router now works again.but feel that this is a scam, programmed in the router to occur within 2 years of purchasing where the settings entered no longer work but once changed works perfectly well.
View 6 Replies View RelatedI was using a wrt54gh which is no longer in working condition.. so i bought an E1200.the problem i face is when i try to restore my new router which is the E1200 frm the backup file frm my previous router the wrt54gh which is saved in my computer i get the error message " THE IMAGE FILE IS INCORRECT ".
View 4 Replies View RelatedI have downloaded the firmware update "Ver.1.0.02 build 11" for my WRT400N from linksys.com several times. I then try to update my firmware on my router. Each time I try, I get an error message that says "Incorrect file path."
View 9 Replies View RelatedThe smart wi-fi app Device List indicates Local Network = 0 (that's incorrect) and Guest Network = 0 (that's correct). When i click Connected Devices for My Network, i see a list of devices but everything indicates 'Offline' and that of course is incorrect.How can i upgrade this software? I recently installed EA6500 and due to being slow, it was recommended to set back to factory default. That process did no go well, so i hope it is not necessary again. This router is not any better then the wrt320N so i am disappointed.
View 7 Replies View RelatedI have several devices connected to my Linksys EA4500. Two of them are my Apple Mac Pro and my Logitech Squeezebox Radio. For some reason, in 'Device List', my Apple Mac Pro has the manufacturer 'Logitech' and the model 'Squeezebox Radio'. As for my Logitech Squeezebox Radio, it doesn't have a manufacturer nor a model. It appears that there is a mix up with these two devices. I have cross checked the IP addresses and MAC addresses displayed in Cisco Connect Cloud with those displayed on the devices and they match - so it's not a case of mixed up names. Could this be an issue with Cisco Connect Cloud?
View 1 Replies View RelatedRouter: Linksys Wireless-G Model: WRT54G v8
Wireless Adapter: Belkin model F7D1101 v1
I have two computers in my house, one is set up directly to the modem/router and the other (in my room) is set up wireless using that belkin adapter above.
Everything has always worked perfectly, but two days ago things went haywire. If my PC connects to the wireless, then it makes the router stop working for the other computer and any wireless devices I have. As long as I don't have my PC connected, then things run smoothly and there are no problems, so it's definitely stemming from my PC?
I thought it might have been the router at first, so I switched it out and it worked fine for over 24 hours, but then the problem came back.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Sunako-PC
Primary Dns Suffix . . . . . . . :
[Code].....
Once again I'm stuck to tethering on my phone due to my router deciding to call it quits for the random moment. I cannot access its control panel, the network just goes kaput. Given that I don't have access to the router since it's part of a double house (the side I'm not on of course), this is getting beyond irritating to reboot it when this happens as that is the only way to fix it. The connections are even wired, too. What kind of money does it take to get a router that is going to STAY on and just work? I'm ready to dump some serious cash into this at this point because this happens at least twice a week anymore. I just want a router that works. It needs to be wireless as my neighbor does use his kindle on it every once and a while.
View 4 Replies View RelatedI was upgrading the FW to 2.07 and after waiting 180 seconds, the router didn't came back, I reset the router and now got a Firmware Upgrade System Ver 1.0.0.2 Date 2009/12/07 Screen when typing 192.168.0.1. Tried to upload all the firmwares starting with 2.00NA and always got the Incorrect hardware ID image, please Check! message.. I can't get the *D-Link Router Recovery Mode* page or any other page. Looks like the firmware update wasn't successful and the router is not longing working, need to find out how to recover from a faulty firmware installation.? Also I open a case with DLink Tech Support, they told me to call Tech Support but I can't access the numbers from my country. I already answered their email like 4 times that I can't access the # and they keep telling me to call the #. Anyway what else I can do to recover the Router.
View 9 Replies View RelatedYesterday my wireless internet just appeared to stop working completely, it has always worked fine up unti now!I have checked all the usual issues, it is nothing to do with my router as i can use other laptops/desktops to access the internet fine.I am using a Pavillion DV6-1215sa which has a Atheros AR9285 802.11b/g WiFi Adapter.It has full strenght but just says Limited Connectivity, so it is picking up the wireless network but wont actually let me connect to the internet via it.
I am able to access the internet when i hard wire the ethernet cable into my laptop, but the just wont work for wireless.I have tried lots of different suggestions so far, but still cannot access the internet.
i've one of my 3500 that when finish to download the os, the front led stop working. During the power on and all the test the led is flashing in various colors pretty ipnotizing :-) When it bacame operative, the led stops. If i issue the test led flashing console command it works.
View 1 Replies View RelatedRegion : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
Few days ago the wireless in my son's Dell Inspiron 620 went bad. It does connect to my old router (WEP), but speed is terrible and connection goes bad after some time. I can also see my modern router and enter the key successfully (WPA2), but it won't connect. Connection to both routers went well for months before, and still goes well from all other devices in the house.
I read the issue with McAfee that was posted late August and followed the steps. Connection in safe mode didn't work. Then I removed McAfee from the PC, no difference. Then I restored the PC to a couple of days before the issues began, removed McAfee again (as it came back through the restore), no difference.
I reinstalled the drivers of the Dell wireless card, no difference.
I have an E1000 wireless router and after rebooting it from the web admin page it won't stop blinking. I tried following the reset instructions on this page but it is still blinking.
[URL]
I can't access 192.168.1.1 via my browser either. Is there anything else that I can try before considering it defective?
my router stop getting internet connection its plugged in but keeps telling me no reset modem or unplug router
View 4 Replies View Relatedmy router stop every exact 3 days, why? when it stop , i don't have net connections and i can't send ping in it?
i try to update de firmware and it do same if i remove de power cable and put it back it start ok?
how i can resolve that?
I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies View RelatedI,ve used a network for a number of years with no problems. I have databases on computer 1 and access them with computer 2. After installing a Cisco e2500 I can connect to the databases but after a short period of time I am disconnected. If I search my network computer 1 is not found. Waiting a few minutes the network will find computer 1 again. At about the same time my firewall software has started to show an attack from an 2 different IP's I don't recognize but its always one of those 2 IP's. I'm assuming the two problems are related. I,ve considered going into my firewall and allowing the unknown IP access, BUT who knows where that IP is coming from. I've checked the Cisco setup but couldn't find an IP address that matched the attacking IP address.
View 1 Replies View RelatedI have a nas device called mybooklive connected to my linksys e2500 router.Every device that is connected to the router does not append nyc.rr.com except the mybooklive one.I change and mad dhcp reservation for this device with the client name but it still appends. [code]
View 1 Replies View RelatedWatch youtube? Router resets! Hookup a wired connection? REBOOT! Hookup a tivo wirelessly, use wifi calling, or listen to spotify.. REBOOT!Is there ANY way for this router to NOT reboot randomly?
View 4 Replies View RelatedI am getting frequent stop pages in streamed video, a message appears on my laptop saying "loading" and a red line beginning traversing the screen. Eventually the line gets across and the video begins again to stream. When I do a speed test I get around 10 Mbps both through the router wireless and hardwired connections. This happens almost every 10 minutes. I have tried rebooting the router and the problem persists
View 9 Replies View Related
