Linksys Wireless Router :: E1200 V1. IPTV (multicast) Is Not Working

Nov 28, 2012

I have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.

View 4 Replies


ADVERTISEMENT

Linksys Wireless Router :: E3000 IPTV Multicast Stream Not Possible

Feb 23, 2011

I've bought a E3000 as replacement for my Linksys WRT350N router.Just upgraded the firmware to version Ver.1.0. 04 (build 6).I use aonTV - an austria IPTV service (Multicast via UDP) - an this worked with my old WRT350N (hw version 1) consistantly well. I hardly had to reboot the router to get the multicast stream.With E3000 I checked the option that it should not filter any multicast traffic - when I reboot the router it works for some time - but after some hours it does not work anymore? I want to watch TV via my HTPC connected via GigaBit Power to the E3000.

View 3 Replies View Related

Linksys Wireless Router :: E1200 Does Not Work IPTV?

Mar 17, 2013

Not far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop.  On WRT320N does not work. Firmware is Ver.1.0.03.

View 9 Replies View Related

D-Link DIR-615 :: IPTV (multicast) Not Working With 4.11 Firmware

Jan 31, 2011

After upgrading firmware from ver 4.00 to 4.11 I can't watch IPTV anymore with VLC. With version 4.00 IPTV works over router (wireless or cable) fine but because of some disconecting trouble I upgraded to ver 4.11. Setup is the same as it was in ver 4.00 including Multicast parameter.

View 5 Replies View Related

D-Link DIR-655 :: Multicast (IPTV) Forwarding Broken In 1.21EU And 1.31EU

May 15, 2010

Upgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.

I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.

Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?

View 2 Replies View Related

Linksys Wireless Router :: E1200 Port Forwarding Not Working

Jan 2, 2013

I set up port forwarding on my router.  When I go to canyouseeme.org and put in my public IP address (I can ping the IP address with no issues) and the port that I'm forwarding it says it can't hit the port.

View 2 Replies View Related

Linksys Wireless Router :: E1200 Not Working After Verizon Modem Change?

Jun 24, 2012

I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.

View 1 Replies View Related

Linksys Wireless Router :: E1200 Stop Working Due To Incorrect Configuration

Feb 14, 2013

I received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.

View 1 Replies View Related

Linksys Wireless Router :: E1200 PPPoE And IPv6 Not Working Fine

Feb 7, 2013

Have a v2 E1200.  Connect with PPPoE to ISP.  IPv4 works fine.  With firmware included on router, 2.0.01, it would receive a /64 of IPv6 from the ISP.  This /64 would show up under 'status' / 'local network'.  Although it did not seem to advertise this space to PC's on my network so I was unable to use it.  I updated firmware to 2.0.04.  Now it does not even pick up the IPv6 /64 at all.
 
Anyone have PPPoE and IPv6 working?  Anywhere I can download 2.0.01 to try it again?
 
Is there a model of router that actually works with IPv6?

View 2 Replies View Related

Linksys Wireless Router :: E1200 No Longer Working After Verizon Modem

Jun 24, 2012

I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
 
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
 
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?

View 2 Replies View Related

Linksys Wireless Router :: E1200 Port Range Forwarding Is Not Working?

Oct 17, 2011

I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
 
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.

View 1 Replies View Related

Linksys Wireless Router :: E1200 System Suddenly Stops Working?

Oct 30, 2012

Right now I have my computer (iMac early 2012 summer purchase) plugged directly into the wall via ethernet cable for internet access.  I have only begun doing this in the past week because my E1200 wireless router has stopped working properly.  I have reinstalled and reset to factory settings and set up with Cisco Connect and setup manually over the past week troubleshooting every possible way I have ever known how. My internet, obviously, is working.  And when I set up the wireless network it connects properly and obtains an IP address and the lights on the back of the unit light up correspondingly and correct.  But I cannot connect to the internet via the router, wirelessly or plugged directly into it.  Yet when I take the internet cable and plug it straight into my computer it works.Mainly just need to know if this can be fixed or if I need to go return this unit and get a replacement.  The router was purchased two months ago and has not had any issues since I first set it up until a couple of weeks ago and my phone is using up all of my cellular data plan without being connected to my wi-fi...

View 1 Replies View Related

Cisco Switching/Routing :: Cat6500 / IPTV Multicast Network Devices High CPU Utilization?

Jan 30, 2013

i have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more  300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.

View 1 Replies View Related

Cisco Linksys E1200 Router Not Working Properly

Mar 7, 2012

The Network icon in the notification area in the bottom right hand corner of my screen will almost always look like this:Quite frequently, though, I will get an exclamation mark inside a triangle with a message instead saying No internet access (I don't have a screenshot). If I give it a few seconds, usually never more than a minute (30 seconds on average it seems), it corrects itself and gives me back internet access.

View 9 Replies View Related

Linksys Wireless Router :: WRT320N Does Not Work IPTV

Oct 25, 2011

Today has bought a router. Before it at me was D-link Dir 320. IPTV on DIR 320 worked perfectly. On WRT320N does not work. Firmware has updated to Ver.1.0.04 build 1. Prompt that it is necessary to make?

View 5 Replies View Related

Linksys Wireless Router :: WRT160N V2 Goes Dead When There Is IPTV Traffic

Aug 20, 2011

I've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes.  All the coax cables in my walls form a wired ethernet network instead of a cable TV network.  To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes.  Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]).  So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.

View 6 Replies View Related

Linksys Wireless Router :: E4200 Not Possible To View IPTV On Computer

Mar 18, 2012

I have bought Linksys E 4200. I'm connected up by protocol PPPoE by my provider, but IPTV doesn't work on my computer.I use the program IP-TV Player and/or VLC Player and both don't work. I only see the list of channel, but any channel doesn't load. Before I used the router DLink Dir 300, and everything was Ok. 

View 3 Replies View Related

Linksys Wireless Router :: Can Setup / Use E3200 To Watch IPTV

Dec 19, 2011

I have Linksys e3200.Can I to setup/use e3200  to watch IPTV?

View 9 Replies View Related

D-Link DIR-601 :: EW-432BRP Not Working With Dish Network IPTV

Jun 6, 2012

I purchased IPTV set-top box from Dish Network (which in turn uses NeuLion services). The set top box works out of the box with TrendNet TEW-432BRP, however the set top box seems to reboot every time I try to launch a channel.The set top box is connected to LAN port 2/DLink is configured to reserve IP address for the set-top box based on its MAC address. The set top is also within its own DMZ so that it does not interfere with firewall settings.

View 1 Replies View Related

Cisco Routers :: Linksys X2000 ADSL2+ Modem Router And IPTV

Jan 7, 2012

I would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.

View 3 Replies View Related

Linksys Wireless Router :: How To Get Best Speeds Possible For E1200

Dec 22, 2012

I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them. 

View 9 Replies View Related

Linksys Wireless Router :: E1200 - Cannot Open NAT?

Jun 5, 2012

I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!

View 7 Replies View Related

Linksys Wireless Router :: E1200 Won't Connect With Key?

Aug 12, 2012

Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password). 

View 9 Replies View Related

Linksys Wireless Router :: Connection From Outside To E1200?

May 1, 2013

I purchased E1200 and have a problem. I  have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.

View 4 Replies View Related

Linksys Wireless Router :: E1200 - Cannot Get It To Connect To TV

Nov 7, 2011

I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet.  I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well.  I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player.  When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV.  CANNOT establish an internet connection?

View 2 Replies View Related

Linksys Wireless Router :: Possible To Use E1200 As Repeater

Jan 4, 2012

Is it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?

View 3 Replies View Related

Linksys Wireless Router :: E1200 - Set It Up With Tablet?

Oct 23, 2012

Bought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.

View 1 Replies View Related

Linksys Wireless Router :: Can't See Where To Set A User Name On E1200

Dec 29, 2011

I can't see where to set a user name on my E1200. I set a password for the web interface then it boots me out and I am promted for the password and username.I don't want to download and configure my router with some poorly written software for my mac;  why can't I just do it all through the good old web interface???? I'm able to set everything else up fine but when i set the password I am basically rendering the web interface usless and have to reset the router!! (running Lion, latest build with 8gigs of ram and N wirless adaptor in lappy) 
 
Ok, so I was given this router for free so I shouldn't complain but I do not see any speed increase over my 6 year old 54G rinning wrt, perhaps I need summin better than this $50 walmart special Getting about 10mps download which is also the theoretical max of G right) 

View 6 Replies View Related

Linksys Wireless Router :: Locked Out Of Own E1200

Jun 9, 2012

I set my router to allow my xbox360's mac address, not knowing that it would kick out all of my other devices. So now I can't access my own router and I need to reset it. How do I do that?E1200 series linksys router. I'm looking for an ethernet cable and my installation disk right now to see if I can connect with the cable and maybe use something on the disk if I have to.

View 1 Replies View Related

Linksys Wireless Router :: E1200 - How To Connect With PC

Dec 26, 2012

I replaced my broken modem with a new Motorola 3360 as recommended by my ISP.  The new modem works fine connected directly to my PC.  When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC.  I've triple checked the wired connections from the modem to the router and then to the PC.  I've swapped out cables and verified that they all work when used directly from the modem to the PC.  I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.

View 2 Replies View Related

Linksys Wireless Router :: E1200 Wi-Fi Does Not Work

Apr 16, 2013

my wifi router is E1200 at first it works very fine but then when the time you unplugged it and turn it on again it won't work already i mean its working the lights are on and blinking but there's no wifi... why does it happen??? i don't understand...i have already did the 30-30-30 rule the hard reset thin but still nothing's change...

View 5 Replies View Related

Linksys Wireless Router :: Firmware For E1200 V2

Dec 29, 2012

i'm having connection issues requiring frequent reboots of my router. it starts with internet slowdown to a crawl, then it times out and lastly the webinterface is not even responding when i try to access it to reboot. Requiring me to manually unplug. this happens once a day atleast.
 
Sometimes it recovers after a few minutes and get on the net.i've tried flashing, reflashing, re-reflashing , resetting , re-resetting, to no end. And all the usual tricks tech support ask to do.
 
i didn't use to have this problem before the firmware update
08/31/2012
Ver.2.0.04 (Build 1)
 
i would just like to flash to the previousl version and test if this still happens.

View 9 Replies View Related

Linksys Wireless-n E1200 New Router Setup Failure

Jan 19, 2012

I have been attempting to set up a linksys wireless-n e1200 router on my hp p6-2007c (Windows 7 SP1, 64-bit) desktop pc for the last day and have exhausted everything i can think of. The previous router was a linksys WRT54G and it worked fine. However, upon setting up this new router i get a "no internet access" message accompanied by the little yellow triangle and the ability to still connect to my router via its ip address to alter its configuration. The connection status for the network and the internet is identical for all the laptops in my house. I originally attempted setting up the router using Cisco's setup program. At its conclusion, the setup program informs me that i am connected to the router, but my internet connection has been lost (even though it was never there) I have tried starting over from scratch by resetting the router back to its default settings and using a variety of different channels (Auto, 1, 6, and 11), frequencies, etc. I have uninstalled norton antivirus, disarmed the windows security programs, made sure of TCP/IP settings, rolled back, uninstalled, and finally updated firmware, uninstalled/reinstalled driver for wireless card, disabled/enabled the card itself, deleted all other previous network profiles still present in the "Manage Wireless Networks" screen, and probably some other suggestions i came across in this forum. They all failed with the same results, i.e. the ability to connect to the network locally and having no internet access.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved