Linksys Wireless Router :: E1200 System Suddenly Stops Working?
Oct 30, 2012
Right now I have my computer (iMac early 2012 summer purchase) plugged directly into the wall via ethernet cable for internet access. I have only begun doing this in the past week because my E1200 wireless router has stopped working properly. I have reinstalled and reset to factory settings and set up with Cisco Connect and setup manually over the past week troubleshooting every possible way I have ever known how. My internet, obviously, is working. And when I set up the wireless network it connects properly and obtains an IP address and the lights on the back of the unit light up correspondingly and correct. But I cannot connect to the internet via the router, wirelessly or plugged directly into it. Yet when I take the internet cable and plug it straight into my computer it works.Mainly just need to know if this can be fixed or if I need to go return this unit and get a replacement. The router was purchased two months ago and has not had any issues since I first set it up until a couple of weeks ago and my phone is using up all of my cellular data plan without being connected to my wi-fi...
View 1 Replies
ADVERTISEMENT
Jul 30, 2012
A few days ago, my Linksys E3200 router stopped working suddenly for no reason. The SSID was still broadcasted for a few days, but no internet connection. Today the SSID does not broadcast at all and I seemingly have no access to it.I tried power cycling it.I tried reconfiguring it via the CD included in the box.I tried solving it with the wireless tools in Windows.
View 2 Replies
View Related
Feb 25, 2010
I have a Studio 1557 laptop (purchased in late December 2009) that all of a sudden has lost wireless connection to the internet. Went to use it last night (Thursday) for normal use and no wireless connection at all. Before this issue, there were no problems connecting thru wireless at all...in fact used it Wednesday evening for work/surfing and no problems whatsoever. We are using a Linksys 160N router...have 2 other computers and 2 iPod Touches that are connecting just fine, absolutely no problems. It can connect thru a wired connection with no problems but nothing thru wireless...this is a fairly new router, about 10 days old, but haven't had any issues with it since set-up.
I didn't have much of a chance to do anything about this last night or this morning. I really don't want to bother calling Dell Support either.
Dell Studio 1557 Windows 7 64-bit, 8gb 1066Mhz, 320HD
View 6 Replies
View Related
Aug 28, 2012
I have a dell studio 1558 laptop and it's got this Bluetooth problem. I use BT to connect to Internet through my phone as a modem. But sometimes it suddenly stops working and the BT icon vanishes from the taskbar. Every attempt to restart it by Wireless switch, or by restarting BT service/process fails. (this does not happen with WiFi, or any other connection though). The only way I get back Bluetooth ON again is if I put the system to sleep, or I shut down and Turn On (Hibernate, Restart, Log off doesn't work). And this happens more frequently while multitasking than normal use.
I am using Windows 7 Home premium (service pack 0).I have the latest Bluetooth module installed, latest system BIOS installed as available in the dell website.
View 1 Replies
View Related
Sep 7, 2012
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit
- All lights lit
- All lights off
- Power and my PC's slot number lit
- etc
View 2 Replies
View Related
May 30, 2012
My M20 Valet Plus stopped working suddenly last night. Now no power lights will come on and it now longer transmitts as a connection point . No apparent sign that it's alive. I've owned it troublefree for just over a year, but it is out of warranty. Any way to tell if there is hope of reviving it or if I'm just out of luck? Nothing happened at my end to cause this -- no power interruptions or other odd occurrences.
View 9 Replies
View Related
Oct 17, 2010
A couple days ago I noticed that my wireless internet connection on my iPhone would cut in and out, then stopped all together. I also had no connection on my mac which is wired to the WRT110. I bypassed the WRT110 and then I had a connection on my Mac meaning the WRT110 is the problem. I haven't changed or added anything lately that could've caused this....
View 9 Replies
View Related
Jul 25, 2011
I have the Linksys WRT54G And it was working fine for years! Then today my computer shut down and when I turned it back on there was a connection but my computer was not responding to any commands. The icon shows full connectivity excellent connection. When I try to go to a web page it shows Connection Error and cannot get to any web pages.I am able to get on other wireless connections from neighbors but not mine. I have gone thru different directions on here and I am not technical and don't understand what is being said. I try to go to 192.168.1.1 and it asks for a password which I don't have. I have tried everything such as password and admin and get nothing.I am able to get my ip address and default gateway address and don't know the next step.
View 1 Replies
View Related
Jun 20, 2011
I was using my iphone one night last week and suddenly it dropped out and now I cannot find it in my WIFI networks page.I am using a Linksys E1000?
View 9 Replies
View Related
Oct 5, 2011
I just bought the E4200 routher at best buy a few weeks ago. I got it all setup how I want it. Its been working fine then about a day ago it started to stop working at random. All internet just stops working. Wired and Wifi. I have to either wait for it to work again or restart the router.
View 7 Replies
View Related
Oct 21, 2011
I have a Cisco Linksys E1000 wireless router. It has been working perfectly for the last few months until yesterday when I noticed none of my wireless devices could connect. The SSID was still being broadcast and my computers that were connected through an ethernet cable were still able to access the internet fine. Eventually I pressed the red reset button on the back of the router, which reset my router name, password, etc. I set everything back up and was able to connect again. Several hours later the wireless stopped working again. When I launched the Cisco Connect software I was prompted to update some software (possibly the router firmware) so I did that. After that I was able to connect to wireless again. This morning I woke up and wireless was not working again. This time I changed the password for the router and then I was able to connect to wireless again. I tried to change the router password back to the original password and I couldn't connect anymore. When I changed the router password back to the new password I could connect again.
View 1 Replies
View Related
Nov 28, 2012
I have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.
View 4 Replies
View Related
Jan 2, 2013
I set up port forwarding on my router. When I go to canyouseeme.org and put in my public IP address (I can ping the IP address with no issues) and the port that I'm forwarding it says it can't hit the port.
View 2 Replies
View Related
Jan 16, 2010
Having a problem with port forwarding on their WRT400N? I'm forwarding one service (https) and this stops working if it's not accessed after a 10 days or so. The only way to get it to work again is to reboot the router. I’m running the “latest" firmware, which is an oxymoron considering it's been over 12 MONTHS since Linksys updated the code... Which is appalling considering this appears to be their flagship wireless N router.
View 5 Replies
View Related
Feb 3, 2013
I'm having a bit of trouble with my e4200, It keeps on "dropping" connection, and by dropping I mean it constantly around 3-5 minutes the internet stops working with all my computers, it's connected by wifi with 2 PC's, and 1 PC is wired with an ethernet cable, and I also have 2 mobile devices connected at it. The internet would start working again within 30s, to 1m, but that it drops soon.Methods I've done to fix it:
-Updated firmware to the latest one
-Set the MTU to 1400
-Reset it, (30 second press)
-Rebooted, (Cooled down, doesn't really run hot just a little warm)
-Restored to factore defaults
View 4 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
View 1 Replies
View Related
Feb 14, 2013
I received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.
View 1 Replies
View Related
Feb 7, 2013
Have a v2 E1200. Connect with PPPoE to ISP. IPv4 works fine. With firmware included on router, 2.0.01, it would receive a /64 of IPv6 from the ISP. This /64 would show up under 'status' / 'local network'. Although it did not seem to advertise this space to PC's on my network so I was unable to use it. I updated firmware to 2.0.04. Now it does not even pick up the IPv6 /64 at all.
Anyone have PPPoE and IPv6 working? Anywhere I can download 2.0.01 to try it again?
Is there a model of router that actually works with IPv6?
View 2 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
View 2 Replies
View Related
Oct 17, 2011
I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.
View 1 Replies
View Related
Mar 9, 2013
I've tried all sorts of settings, and I'm still holding out that its a setting possibly, but I have a E3500 and devices on both 5Ghz and 2.4Ghz... Most of them, probably when idle, seem to stop working over WIfi. They still have decent connection, but every internet related request just times out. Disable and reinable the wifi and it works great again.
Could this be defective wifi radios? or could it really be interference? I have it happening on multiple devices. Also, I'm not far away from the router when it occurs, and when I reconnect, it seems to work just fine for a while. Basically the big problem is on the cell phones and tablets because I'll miss notifications... I'll turn off the wifi and turn it back on when I use the device next, then a flood of notifications will come in. Again, it's not just a phone thing, tablets and laptops have the same problem, that's just the main reason I want it fixed.
View 5 Replies
View Related
Mar 14, 2012
I have the same problems with the Cisco EPC3925?Everytime a wired pc reboots/boots everyone on the network losses internet, also wireless is disconnected. Also everyone get unidentified network and later its set to public network.We are using a Sitecom switch LN-120. I have to unplug this switch, then restart the router to fix the problem each time. Then I can plug it in again and everything is fine.The router will not restart (does not go further then 2nd blinking LED.) if I do not unplug the switch.
View 8 Replies
View Related
May 3, 2011
I think the built-in wi-fi of my laptop was destroyed so I connected a usb device that enables me to use wi-fi. Now, I tried to use internet, I was connected however connection was slow plus after a few minutes when I open another window it won't just connect. The window shows a blank page and on the tab it says untitled. I don't know what's the problem and what should I do to fix it.
View 2 Replies
View Related
Mar 7, 2012
The Network icon in the notification area in the bottom right hand corner of my screen will almost always look like this:Quite frequently, though, I will get an exclamation mark inside a triangle with a message instead saying No internet access (I don't have a screenshot). If I give it a few seconds, usually never more than a minute (30 seconds on average it seems), it corrects itself and gives me back internet access.
View 9 Replies
View Related
Apr 29, 2013
My internet connection suddenly stops for about 30 minutes of using it. I need to restart so that I can connect again.
View 1 Replies
View Related
Oct 26, 2011
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies
View Related
Sep 29, 2011
My dlink dir 628 wireless router suddenly stopped working yesterday. If I plug the ethernet cable directly into my computer and the internet works. I see the wireless profile in the options for the wireless internet, but when I try to connect, it is unable to do so.
I've tried resetting the router (using the button on the device) witand reinstalling the router (using the CD), but still not working. Also have tried turning off the modem, router, and restarting my computer.
View 4 Replies
View Related
Jan 29, 2013
I can no longer browse through any browser, or update any programs (even though I am still connected to my wireless router). I have already done a Refresh, but the problem persists
View 2 Replies
View Related
Jul 4, 2012
We use our internet to watch Netflix. We have had no problems until recently, I called the satellite Internet company(which is a local co.) they told me my router was going out. I bought a new one, problem solved! Right?!? WRONG my husband told me my neighbor just got Internet and has been playing Xbox everyday which coincidently is between the 5:30pm to 10ish pm we have been having issues with our router. What can we do to fix this? Do I have to buy a bigger router? He is not stealing off mine because it is password protected that was changed when new router was setup and programmed. I have been running of a Cisco Linksys E2500 advanced dual band n router. The router is in the same room as the TV accessing it, which we previously had no issue connecting anywhere in the house or garage.
View 1 Replies
View Related
Oct 1, 2012
My wireless connection for 2,4 GHz stopped working correctly. Here's the set up:
I have an E4200 Linksys router. Furthermore I have a desktop running on Windows7 connected to the router with a wire. No problem there. I can connect to the Intenet via the E4200 and a modem.Then I have a notebook also running on Windows7. Until yesterday it was wireless (2,4 GHz) connected to the router and to the Internet, but now I can see the router on the networklist (so there is connection), but it will not make contact to the Internet. If I hook up the notebook with a line to the router it works OK.Then I have an iPad which makes a wireless connection to the Internet (via the router) for the 5 GHz option, but it does not make a connection with the 2,4 GHz option anymore (before yesterday this worked well). I did not change any settings on the Linksys or other network options, Can an update from McAfee make a difference (only for 2,4 GHz?).
View 9 Replies
View Related
Nov 1, 2012
called my internet company yesterday with a problem that my internet was not working.. so we went through some steps and basically he had me remove the wireless cord from the router put it into my computer (at the time it wasn't working via that either) and reset my ip, it started working after that and he just said I must've gotten a faulty ip. Now it still won't get internet from my router, we all have laptops in the house so wifi is essential. The internet light on the router still blinks green.[CODE]
View 15 Replies
View Related
Oct 2, 2011
I've been using my DCS-930L happily for the last month. Today, it suddenly stopped working. I haven't made any changes to my network or any configurations in about 2 weeks, during which the camera has worked fine locally as well as remotely. Now, if I unplug/plug it back in, the camera will immediately connect. However, after a period of time, it's no longer accessible, even from my local network. When I try to log-in to the camera or view it, it cannot be found or connected to. So it doesn't seem to be any of my configuration, but something that's intermittent or happens after awhile.
View 1 Replies
View Related
Mar 6, 2012
I am having a very strange issue on LMS 3.2
The problem is that the syslog collection suddently stops receiving logs and writing them into the syslog.log file
I have checked the following:
- Packet sniff to make sure that logs are being received on the server's NIC interface
- Checked the UDP port 514 is bound to the crmlog process.
- Checked the crmlog is running.
When i restart the server, the syslog connections works for a week or two and save the received logs in the syslog.log file, but after that it suddenly stops collecting log again, all the above points stays valid (service running, UDP Port...)
I have attached the LMS's modules versions installed on the server.
View 1 Replies
View Related
