After upgrading firmware from ver 4.00 to 4.11 I can't watch IPTV anymore with VLC. With version 4.00 IPTV works over router (wireless or cable) fine but because of some disconecting trouble I upgraded to ver 4.11. Setup is the same as it was in ver 4.00 including Multicast parameter.
View 5 RepliesI have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.
View 4 Replies View RelatedUpgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.
I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.
Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?
I purchased IPTV set-top box from Dish Network (which in turn uses NeuLion services). The set top box works out of the box with TrendNet TEW-432BRP, however the set top box seems to reboot every time I try to launch a channel.The set top box is connected to LAN port 2/DLink is configured to reserve IP address for the set-top box based on its MAC address. The set top is also within its own DMZ so that it does not interfere with firewall settings.
View 1 Replies View RelatedI've bought a E3000 as replacement for my Linksys WRT350N router.Just upgraded the firmware to version Ver.1.0. 04 (build 6).I use aonTV - an austria IPTV service (Multicast via UDP) - an this worked with my old WRT350N (hw version 1) consistantly well. I hardly had to reboot the router to get the multicast stream.With E3000 I checked the option that it should not filter any multicast traffic - when I reboot the router it works for some time - but after some hours it does not work anymore? I want to watch TV via my HTPC connected via GigaBit Power to the E3000.
View 3 Replies View Relatedi have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more 300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.
View 1 Replies View RelatedMy DIR-655 stopped working after updating firmware to 3.35. Only power light comes on. port4 flashes for a microsecond when I plug it in. Recovery mode has not done anything. Computer acts like nothing is connected through Ethernet, says "No Cable Connected." Only power light stays on the whole time. I am guessing this thing is broken now. when i go through ipconfig, "no media connected." If not whats a good router under a hundred bucks today, had this router since early 2007.
View 10 Replies View RelatedRegion : India
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL EVDO
I have one BSNL EVDO data card which was working fine before firmware upgrade to latest 3.14.2 Build 120822 Rel.57775n. Now it is keep on saying device unplugged after identifying the device. The device is working fine while connected on my laptop.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : TL-WR1043ND_V1_130325
ISP : Ip dinamics
It worked correctly 2 days and 16 hours.Now, does not surfing in internet.although I can go to web interfaceI turn the gargoyle.The developers of TP-Link me tired
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1.8
Firmware Version : wr1043nv1_en_3_13_12_up_boot(121210)_UN_beta
ISP : fibertel argentina
The TP-Link managers surely have read the constant complaints about the performance of the WR1043ND, are innumerable and of all kinds, but especially, due to instability.There are two beta versions, but they are very unstable.I beg, TP-Link, keep us informed on the development of the new firmware.When I bought this router, I was hoping a correct performance.
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
I have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies View RelatedMulticast is not working between our two datacenter, we have catalyst 2960S (two stacked) as the internal lan switch, and catalyst 3560E as the external switch, same configuration for both datacenters.The two sites are connected using metro, the external switch (3560) is doing qinq and encapsulate the data from the internal switch with the metro vlan (611).
IGMP snooping is disabled for all switches, although we prefer to enable it for the internal switches.For each datacenter there is a different firewall which also act as the router, we are using fortigate as the firewall.Following is the important configuration section:
Port 43 in the internal switch is connected to the external switch (both sites):
interface GigabitEthernet1/0/43
switchport mode trunk
load-interval 30
Port 3 in the external switch connected to the internal switch (both sites):
interface GigabitEthernet0/3
switchport access vlan 611
switchport mode dot1q-tunnel
no cdp enable
no cdp tlv server-location
no cdp tlv app
Port 8 on the external switch connected to the metro link (both sites) vlan 350 is the internet and 611 is the metro:
interface GigabitEthernet0/8
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 350,611
switchport mode trunk
vlan 611 on external switch:
interface Vlan611
ip address 192.168.168.2 255.255.255.0
no ip route-cache
no ip mroute-cache
Why do we need MP-BGP (and not BGP) to exchange multicast prefixes between multicast domains?
View 2 Replies View RelatedI try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
here is my config:
ip routing
!
ip vrf vpn2
rd 1:1
mdt default 232.1.1.1
route-target export 1:1
route-target import 1:1
[code]....
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]
Can you use the NA firmware on an EU firmware device?I assume yes, since the hardware is the same?What's the difference between the two?
View 14 Replies View RelatedI am having trouble getting some multicast traffic across a link. I have a 3750G setup, with IP routing and IP multicast routing, between two laptops. This will eventually sit between two networks that cannot be physically connected to each other for security reasons. I have static joins on the ports but cannot see the multicast traffic on the receiver. I am attaching the latest config. The sender(10.10.4.2) sits on gi1/0/24 and the receiver(10.10.3.2) sits on gi1/0/1. I am using VLC to test this and it will connect if I point the receiver to the address of the sender, but will not receive any multicast. The multicast traffic is not making it to the 10.10.3 side, I used wire shark to verify that it was not making it across.
View 3 Replies View RelatedMy topology is a physical ring, and I need transfer IPTV signal to all site along the ring.For example:
A (headend)--- B --- C --- D
|______________________|
Note: -----: have spoke-mesh defination
_____: no spoke-mesh defination to prevent loop
So, with MPLS/VPLS I can implement it. With spoke and mesh defination, the traffic can transfer form A to B, C or D as drop-continute action in ring topology (between different VC). Everything is good, FRR can work very fast. But when the topology have a failure link, for example the link between B and C, at that time the traffic will go from A to B then B come back to A and A --- D ---C. This action is so stupid, because it can increase delay, jiiter in network. On the other hand, when the node failure ( B failure), C will loss the IPTV signal, even the link from A--D--C always good.
i am signed up for an IPTV service. my service provider set up their own hardware including a reciever and a wireless modem. but their wireless modem has weak signal and i cannot connect to it using my computer in the other room. so i wanted to set up my WAG54GP2 modem to use with IPTV service. but i couldn't. i have followed the instructions described there:
[URL] (support page for some other IPTV provider, i guess)
so, i have checked the configuration details of the other modem which is provided by the IPTV company and found out that encapsulation mode is selected as "DHCP" instead of "Bridge mode only". But my linksys modem does not have an option named "DHCP". so, does it mean that it is impossible to use IPTV with my WAG54GP2 modem?
how to update Cisco FIrmware ... it is like brick....no responce from router.. i have tried With Linksys TFTP,, just coppying successful and not working..
View 1 Replies View RelatedNot far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop. On WRT320N does not work. Firmware is Ver.1.0.03.
View 9 Replies View RelatedToday has bought a router. Before it at me was D-link Dir 320. IPTV on DIR 320 worked perfectly. On WRT320N does not work. Firmware has updated to Ver.1.0.04 build 1. Prompt that it is necessary to make?
View 5 Replies View RelatedI have wirless router WRT54G ver.2. and I had firmware 2.0 So I downloaded new firmware From Here and did exactly as in instruction.
After update went successful I unplaged my router for 30 seconds but it's not working. I mean it's flashes and everything but can't access it and it is not broadcasting. and whats most interesting, reset buttom is not working
Want can I do? can I access it with some other way and reinstall firmware?
I have been having trouble with my router with wireless network intermittently cutting out every couple minutes (on all devices, like laptop, phone, and tablet.) So, in my wisdom, I went online and downloaded version 2 firmware and after power cycling the wireless doesn't work anymore. Questions:
I have my old Dell Desktop connected (hardwired) into the router, and it works when I take the wireless router out of the loop. How do I update the firmware on the router if I can't connect wirelessly or hardwire anymore? I want to go to version 1 to see if that will solve the original issue.
For the original issue of cutting out and reconnecting constantly, would version 1 work or something else? It isn't my cable modem, as internet has always worked fine connecting desktop or laptop directly.
I've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes. All the coax cables in my walls form a wired ethernet network instead of a cable TV network. To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes. Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]). So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.
View 6 Replies View RelatedI have bought Linksys E 4200. I'm connected up by protocol PPPoE by my provider, but IPTV doesn't work on my computer.I use the program IP-TV Player and/or VLC Player and both don't work. I only see the list of channel, but any channel doesn't load. Before I used the router DLink Dir 300, and everything was Ok.
View 3 Replies View RelatedI have Linksys e3200.Can I to setup/use e3200 to watch IPTV?
View 9 Replies View RelatedIs it possible to establish a connection to an IPTV service with the N150 wireless router?
View 1 Replies View RelatedI need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies View Relatedwe have Catalysts 2960S for switching in our Wireless high capacity backbone network. As agregation switch we are using 3560x.
I just need to know, if are these 2960S good solution for igmp snooping for whole IPTV stream. It put only a range from backbone and put out on another port. But just specified multicast addresses.
Imput will be 239.128.0.10 to 239.128.0.20 on Gi 0/1,Output wil be 239.128.0.10 - 15 on Gi 0/24
IPTV will be separated on different VLAN for eg VLAN 20,Is needed any priorization configured od switches?,The capacity for IPTV is around 500 mbps
I have a WRT610N (v2) router and I recently updated the firmware to the most current version 2.00.01 build 15. I can no longer set WPA2 security for both bands (used to work just fine). Every time I try to save settings for WPA2 for the 5 GHz band, it tells me it was successful but then displays that the security mode is disabled (and it shows up on my computers list as not having any security enabled. If not, where can I get a copy of the old firmware that worked?
View 8 Replies View RelatedI would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies View Related