I have bought Linksys E 4200. I'm connected up by protocol PPPoE by my provider, but IPTV doesn't work on my computer.I use the program IP-TV Player and/or VLC Player and both don't work. I only see the list of channel, but any channel doesn't load. Before I used the router DLink Dir 300, and everything was Ok.
View 3 RepliesInstalled E4200 with an iMac running MacOS X Version 10.6.8. Wireless connection works great. Also connected a wireless laptop without a problem. But can't connect a 2nd computer is wired. That is a PC running Vista. I know the wiring is good, because the E4200 is a replacement router in a network that was working fine.
View 1 Replies View RelatedMy old dLink DIR-655 router could serve as an NTP server for all the computers on my network. It would get the time from the dLink NTP time source and allow me to sync all the systems on my home network off the DIR-655.
I had to replace it with this new E4200 but don't see an option for it to act as a time source for my internal network.
Can this router be used for this function?
Have just changed my E4200 to EA4500 but can my computer has not IE access. Both router has same settings and the mac adr are both in the modem at the local cabel firm.
View 4 Replies View Relatedthere has been issues with this router, and I wonder if any of you have issues connecting to the 5ghz when you wake your pc from sleep longer than an hour. For some reason when I put my computer to sleep at night and wake it up in the morning, my computer will not connect to 5ghz. It will work fine with 2.4, both are set in auto, so I dont see any issues. I did try to put 5ghz to a manual setting; wpa2, 40 mhz, and channel 161. I still get the same results. I am doing something wrong or is the router's 5ghz faulty?Also when is the new firmware coming, I am getting sick of my Harddrive being awake 24/7, its killing the harddrives life span and wasting electricity. I should put this in another post, because they should really change the media server to Wild Media Server or Serviio it would be alot better.
View 7 Replies View RelatedI got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost don't work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit out All other computers, tv. printer wireless work very fine.
View 2 Replies View RelatedNot far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop. On WRT320N does not work. Firmware is Ver.1.0.03.
View 9 Replies View RelatedToday has bought a router. Before it at me was D-link Dir 320. IPTV on DIR 320 worked perfectly. On WRT320N does not work. Firmware has updated to Ver.1.0.04 build 1. Prompt that it is necessary to make?
View 5 Replies View RelatedI have the E4200 with latest firmware . When I connect my computer to the E4200 and that to my modem im getting about 50mb speed. If I disconnect the E4200 and connect my computer straight to the modem I get about 95mb speed?I have the Virgin Broadband 100mb service and all is working fine at their end.
View 2 Replies View RelatedI've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes. All the coax cables in my walls form a wired ethernet network instead of a cable TV network. To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes. Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]). So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.
View 6 Replies View RelatedI have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.
View 4 Replies View RelatedI've bought a E3000 as replacement for my Linksys WRT350N router.Just upgraded the firmware to version Ver.1.0. 04 (build 6).I use aonTV - an austria IPTV service (Multicast via UDP) - an this worked with my old WRT350N (hw version 1) consistantly well. I hardly had to reboot the router to get the multicast stream.With E3000 I checked the option that it should not filter any multicast traffic - when I reboot the router it works for some time - but after some hours it does not work anymore? I want to watch TV via my HTPC connected via GigaBit Power to the E3000.
View 3 Replies View RelatedI have Linksys e3200.Can I to setup/use e3200 to watch IPTV?
View 9 Replies View RelatedI would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies View RelatedI have WRT54GS I can't view the setting tab to check or change. It seem the tabs are light in color and I click on them. I did have a virius which I got rid of. I have removed the linksys software and re installed
View 1 Replies View RelatedI've recently upgraded my home network and now my wdtv can't connect to my shared hdd's on my pc for streaming purposes. Previously I had some piece of **bleep** G router/modem combo from Verizon and I didn't have any problems accessing my network shares, I did have a streaming problem with some .mkv's because the signal was so poor. I Finally dropped some cash on a d-link modem and an linksys E3000 router. Here's the messed up part, if my wdtv is plugged, physically, into my router I can access my shares just fine. I can stream movies with out any lag what so ever. If I go wireless (as I have previously been with the old westell router/modem combo) I can no longer see my network shares. I can connect to the internet and do netflix, pandora, ect. But when I go under network shares all that shows up is my router..
View 1 Replies View RelatedI currently have 2 e4200 wireless routers. The first router is connected to 3 devices via ethernet, and the 4th port is connected to my other e4200v2 which is set as bridge mode. The main router is at one end of the house, the second bridge mode router is at the other end.My wireless devices are connected to the main e4200v2, along with all the wired clients.
When wirelessly connected to the 2nd e4200 (the bridged one) I cannot connect to or ping any wireless clients that are connected to the main router. (For example, in my bedroom I am connected with my computer to the 2nd bridged router, and I am trying to ping my other computer that is wireless connected to the main router. I am unable to ping to this computer. When I am conected wirelessIy to the mian router, than I am able to ping the other wireless computer on the same router. Note:I am able to access any hard wired devices to the main router, regardless of which router I am connected to. The issue only appears to be when trying to connect to a wireless device that is connected to a different router than the device I am connecting from.Both routers are setup on the same subnet mask with firmware Ver.2.1.39.145204
I purchased some cameras for my building. I have them set up ok on port 85 but I can't view them remotely until I set up the router to forward the port. I have a charter modem and the E2500 router.
View 1 Replies View RelatedIs it possible to set up additional PVC for IPTV on LinkSys x3000?
View 4 Replies View Relatedi am signed up for an IPTV service. my service provider set up their own hardware including a reciever and a wireless modem. but their wireless modem has weak signal and i cannot connect to it using my computer in the other room. so i wanted to set up my WAG54GP2 modem to use with IPTV service. but i couldn't. i have followed the instructions described there:
[URL] (support page for some other IPTV provider, i guess)
so, i have checked the configuration details of the other modem which is provided by the IPTV company and found out that encapsulation mode is selected as "DHCP" instead of "Bridge mode only". But my linksys modem does not have an option named "DHCP". so, does it mean that it is impossible to use IPTV with my WAG54GP2 modem?
i want to view computer screens on my network how can i do this without them knowing?
View 3 Replies View Relatedview a history of IPs that have connected to my computer. Specifically those that accessed my computer through a remote desktop connection? I believe I can check and see the ip while someone is connected but not after they disconnected.
View 1 Replies View RelatedI can not view work group connections on my computer especially when I tried to view the work group connections it always showed the message like this work is not accessible you might not have permission to use this network resource.
View 6 Replies View RelatedI have a recurring issue with my e4200v1. My wired and wireless connections work fine, but I can't get to the administration website. I have https only set up, and after I get thru the 'certificate error' screen, I get an error that says web page is unavailable. Firfefox tells me that the connection was lost - error 101.I have tried wired and wireless, multiple computers, multiple browsers. I even turned the firewall off on one computer (or I think I did anyway).The only way I know how to fix it is by completely resetting then setting up the router all over again.
View 2 Replies View RelatedUpgraded from WRT610N to E4200. Since upgrading to latest firmware the wan just disappears both 5 and 2.5 Ghz bands. Happened with older firmware but not as often. Using it in briged mode. When this happens I can't even get to the management page with a lan connected pc. Have to do a hard reboot to get it to respond again. This is unacceptable for a router at this price point.
View 2 Replies View RelatedI am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
I bought Linksys E4200, at a time that is the TOP of the line Cisco routers for Home use.I noticed a serious usage issue with it, I could not identify which are the wifi devices connected to choose for access restriction or parental controls, as the dialog box state only as "Network device", and software control by Linksys does not have any provision to use MAC ID or any other option "except " looking at the dialog box as "Network device".
View 4 Replies View RelatedHow to connect the e4200 to a mac via afp? Trying to mount the network drive so the mac see it and can use for time machine backup.
View 3 Replies View RelatedTrying to update it to the new smart Wifi but getting this error "Incorrect Image File".Yes Ive tried redownloading yes ive tried different browers and yes to unziping the file! and Yes Im downloading the correct version I even tried version 1 for the heck of it and still nothing.
View 3 Replies View RelatedI just received by replacement e4200 v1. I updated the firmware to 1.0.03 build 14 and am up and running just fine. The specs say e4200 should be 300+450Mbps. I am using a software "inSSider 2.0" to view my wireless setup. I get 144(N) at 2.4GHz and 450(N) at 5.2GHz. Please note these are max bit rates and not connect speed or throughput rate. The "inSSider" software gives me the following:
2.4GHz - 1/2/5.5/6/7/9/11/12/14/18/22/124/28/29/36/43/44/48/54/58/65/72/86/116/130/144
5.2GHz - 6/9/12/15/18/24/30/36/45/48/54/60/90/120/135/150/180/240/270/300/360/405/450
I get this information by hovering on the max bit rate field on the row displaying my SSID. So is it correct to say that my e4200 is not designed to reach 300Mbps at 2.4GHz. There is an earlier discussion thread about connection maxing out 144. Please note I am not talking about connect speed or thru-put speed. Max design bit rates of dual band router labeled e4200.
Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
View 5 Replies View RelatedFirmware 1.0.00 on my E4200 Hardware v1.0 provided a functioning 6to4 tunnel through Comcast's 6to4 facility. Windows and Linux clients on my local network discovered IPv6 addresses and were able to use them successfully.Unfortunately, after the upgrade to 1.0.03 this functionality was gone. I missed reading the ChangeLog, which said that the automatic tunneling feature was removed in 1.0.01. The now provided IPv6 functionality works much less well. First, automatic configuration (discovery of the 6to4 via IPv4 anycast) no longer works with Comcast's gateway. If I configure the tunnel manually, by specifying a 2002/16 prefix, I regain IPv6 connectivity, but only for Linux clients on my local network.
Windows 7 clients suffer from the problem that because the E4200 hands out ULA addresses, they end up preferring those ULA addresses when making global IPv6 connections in the IP 'source' field, which of course does not work. It's like putting your company mailbox code as the return address on a letter you send via US Mail. Other home routers, such as the AVM Fritz! (url,...) suffer from the same problem. However, they provide an option to turn off ULA at the router.Is it possible to turn off ULA for the E4200?