Not far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop. On WRT320N does not work. Firmware is Ver.1.0.03.
View 9 RepliesI have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.
View 4 Replies View RelatedToday has bought a router. Before it at me was D-link Dir 320. IPTV on DIR 320 worked perfectly. On WRT320N does not work. Firmware has updated to Ver.1.0.04 build 1. Prompt that it is necessary to make?
View 5 Replies View Relatedmy wifi router is E1200 at first it works very fine but then when the time you unplugged it and turn it on again it won't work already i mean its working the lights are on and blinking but there's no wifi... why does it happen??? i don't understand...i have already did the 30-30-30 rule the hard reset thin but still nothing's change...
View 5 Replies View RelatedMy 1200 v 1.0 was working fine until I tried to link a wireless internet camera. Apparently I screwed something up in the setup such that I've lost my WiFi connection to my laptop and one wireless desktop. Fortunately my wired connection still works. I've carefully tried to restore my system following the online procedure and while the setup looks OK it doesn't link. In the process I have reset the router to the factory setting several times and have installed the latest firmware version. I contacted Linksys support and using remote diagnosis they reached a point where they said that something was wrong with my computer and to investigate further there would be a fee charged. I balked at that since I had tried the setup from several different wired Window 7 and XP computers.
View 9 Replies View RelatedI was successful in configuring a new e1200 in bridge mode to extend my network. I did this with the routers side by side. In then moved the e1200 to a new location 150 feet away and it will not work. I previously had this working with an older linksys router. It will not deliver a Internet connection.
View 8 Replies View RelatedI have a new E1200 router. I VPN from home to my work computer just fine. since I can remotely access the router from work...what setup section of the router would I need to utilize to go backwards and access my home PC thru remote desktop? NAT? if so what are the instructions to do so.
View 1 Replies View RelatedI've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes. All the coax cables in my walls form a wired ethernet network instead of a cable TV network. To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes. Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]). So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.
View 6 Replies View RelatedI've bought a E3000 as replacement for my Linksys WRT350N router.Just upgraded the firmware to version Ver.1.0. 04 (build 6).I use aonTV - an austria IPTV service (Multicast via UDP) - an this worked with my old WRT350N (hw version 1) consistantly well. I hardly had to reboot the router to get the multicast stream.With E3000 I checked the option that it should not filter any multicast traffic - when I reboot the router it works for some time - but after some hours it does not work anymore? I want to watch TV via my HTPC connected via GigaBit Power to the E3000.
View 3 Replies View RelatedI have bought Linksys E 4200. I'm connected up by protocol PPPoE by my provider, but IPTV doesn't work on my computer.I use the program IP-TV Player and/or VLC Player and both don't work. I only see the list of channel, but any channel doesn't load. Before I used the router DLink Dir 300, and everything was Ok.
View 3 Replies View RelatedI have Linksys e3200.Can I to setup/use e3200 to watch IPTV?
View 9 Replies View RelatedI would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies View RelatedI have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies View RelatedI have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies View RelatedSetting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies View RelatedI purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies View RelatedI have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies View RelatedIs it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?
View 3 Replies View RelatedBought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.
View 1 Replies View RelatedI can't see where to set a user name on my E1200. I set a password for the web interface then it boots me out and I am promted for the password and username.I don't want to download and configure my router with some poorly written software for my mac; why can't I just do it all through the good old web interface???? I'm able to set everything else up fine but when i set the password I am basically rendering the web interface usless and have to reset the router!! (running Lion, latest build with 8gigs of ram and N wirless adaptor in lappy)
Ok, so I was given this router for free so I shouldn't complain but I do not see any speed increase over my 6 year old 54G rinning wrt, perhaps I need summin better than this $50 walmart special Getting about 10mps download which is also the theoretical max of G right)
I set my router to allow my xbox360's mac address, not knowing that it would kick out all of my other devices. So now I can't access my own router and I need to reset it. How do I do that?E1200 series linksys router. I'm looking for an ethernet cable and my installation disk right now to see if I can connect with the cable and maybe use something on the disk if I have to.
View 1 Replies View RelatedI replaced my broken modem with a new Motorola 3360 as recommended by my ISP. The new modem works fine connected directly to my PC. When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC. I've triple checked the wired connections from the modem to the router and then to the PC. I've swapped out cables and verified that they all work when used directly from the modem to the PC. I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.
View 2 Replies View Relatedi'm having connection issues requiring frequent reboots of my router. it starts with internet slowdown to a crawl, then it times out and lastly the webinterface is not even responding when i try to access it to reboot. Requiring me to manually unplug. this happens once a day atleast.
Sometimes it recovers after a few minutes and get on the net.i've tried flashing, reflashing, re-reflashing , resetting , re-resetting, to no end. And all the usual tricks tech support ask to do.
i didn't use to have this problem before the firmware update
08/31/2012
Ver.2.0.04 (Build 1)
i would just like to flash to the previousl version and test if this still happens.
I have been attempting to set up a linksys wireless-n e1200 router on my hp p6-2007c (Windows 7 SP1, 64-bit) desktop pc for the last day and have exhausted everything i can think of. The previous router was a linksys WRT54G and it worked fine. However, upon setting up this new router i get a "no internet access" message accompanied by the little yellow triangle and the ability to still connect to my router via its ip address to alter its configuration. The connection status for the network and the internet is identical for all the laptops in my house. I originally attempted setting up the router using Cisco's setup program. At its conclusion, the setup program informs me that i am connected to the router, but my internet connection has been lost (even though it was never there) I have tried starting over from scratch by resetting the router back to its default settings and using a variety of different channels (Auto, 1, 6, and 11), frequencies, etc. I have uninstalled norton antivirus, disarmed the windows security programs, made sure of TCP/IP settings, rolled back, uninstalled, and finally updated firmware, uninstalled/reinstalled driver for wireless card, disabled/enabled the card itself, deleted all other previous network profiles still present in the "Manage Wireless Networks" screen, and probably some other suggestions i came across in this forum. They all failed with the same results, i.e. the ability to connect to the network locally and having no internet access.
View 1 Replies View RelatedI have a linksys e1200 wireless router and the internet port does work. Is there a way to make one of the lan ports the internet ports?
View 1 Replies View RelatedI can connect to the guest account but it cannot resolve DNS addresses; how should the router be set up?
The regular (non-guest) account works as advertised. The E1200 is connected to my Verizon modem/router. I have tried disable/enable of DHCP on the E1200; I have tried setting the E1200 Static DNS 1 to my Verizon router IP address without success.
I just installed an E1200 router and used the CD to take care of the software work. I Cannot connect to it by WiFi. I still have to use a cable connection.
View 4 Replies View RelatedI want to prevent a wired pc with a static ip from accessing the internet on an e1200 router, but the computer does not show up in the list under "parental controls". I have tried adding it to the dhcp reservation table manually, but it still does not show up. There are, however, several unspecified "network devices" on the list. How can I do this?
View 7 Replies View RelatedI wish to have a home network using the E1200 without an internet connection. I have a netbook (Lenovo S100) and a Samsung Galaxy Note II. I want to be able to have both connected to the router so I can interface the two devices using a program such as Teamviewer.
View 1 Replies View RelatedI just got a Macbook Air and couldn't get connected at home so I went and bought a new router (our other router was old!!). We purchased the E1200. Our Dell desktop seems to have a fine connection, but my MacBook Air and my husbands laptop are really slow when on the internet.
View 1 Replies View RelatedI'm having getting my E1200 to work is this; I'm connected wirelessly with an N-adapter to the router, my roomate is connected directly with an Ethernet cable and to the modem. Whenever he logs ons or logs off from internet I GET DISCONNECTED! Its very frustrating. At first I kept wondering why I would get frequent Disconnects, until I matched exactly the times he would log on or log off. I've never seen this type of problem before in my previous router?
View 9 Replies View RelatedIn one area of the home is a century link pk 5000 modem that connect to the internet. In another area of the home is the computer that has an e1200. Is it possible to connect the computer to the internet, wirelessly, from the e1200 to the pk5000? How is this accomplished?
I know the settings for the pk5000 and would "input" them into the e1200 if I friggen knew where to do this.
My ISP requires MAC authentication on the router for internet access. They provide the router, and register that router to their access list.I'm not very happy with the router they provided, so I'm planning to buy a E1200 and clone my current router's MAC address. But when I checked the interface of this router, the mac cloning page has a button saying "Clone my PC's MAC". And in the FAQ page of E1200 it says that the router can automatically capture the MAC address of the PC. Which is not what I want to do.I want to manually input my older router's MAC address into this router to clone it.
View 1 Replies View Related