Linksys Wireless Router :: Can't Get Wifi To Work On E1200
Feb 23, 2013
My 1200 v 1.0 was working fine until I tried to link a wireless internet camera. Apparently I screwed something up in the setup such that I've lost my WiFi connection to my laptop and one wireless desktop. Fortunately my wired connection still works. I've carefully tried to restore my system following the online procedure and while the setup looks OK it doesn't link. In the process I have reset the router to the factory setting several times and have installed the latest firmware version. I contacted Linksys support and using remote diagnosis they reached a point where they said that something was wrong with my computer and to investigate further there would be a fee charged. I balked at that since I had tried the setup from several different wired Window 7 and XP computers.
View 9 Replies
ADVERTISEMENT
Apr 16, 2013
my wifi router is E1200 at first it works very fine but then when the time you unplugged it and turn it on again it won't work already i mean its working the lights are on and blinking but there's no wifi... why does it happen??? i don't understand...i have already did the 30-30-30 rule the hard reset thin but still nothing's change...
View 5 Replies
View Related
Mar 17, 2013
Not far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop. On WRT320N does not work. Firmware is Ver.1.0.03.
View 9 Replies
View Related
Aug 5, 2012
I was successful in configuring a new e1200 in bridge mode to extend my network. I did this with the routers side by side. In then moved the e1200 to a new location 150 feet away and it will not work. I previously had this working with an older linksys router. It will not deliver a Internet connection.
View 8 Replies
View Related
Dec 12, 2011
I have a new E1200 router. I VPN from home to my work computer just fine. since I can remotely access the router from work...what setup section of the router would I need to utilize to go backwards and access my home PC thru remote desktop? NAT? if so what are the instructions to do so.
View 1 Replies
View Related
Dec 26, 2012
I received a Linksys E1200 Wi-Fi Router for Christmas. I inserted the Setup CD into my iMac, running OS X version 10. 8. 2. I clicked on setup and a window opened with the message "Unsupported operating system".At this point I don't plan to use the Wi-Fi for the computer, but I do need to connect the ethernet cable to the router, then to my computer.I will be using Wi-Fi for my iPad. In that case, I have no instructions on how to set up the router for my iPad. Will this Wi-Fi router work or will I need a router compatible with OS X version 10.8.2?
View 1 Replies
View Related
Feb 6, 2013
My Wi-Fi keeps on freezing and I have to unplug it all the time. I have the e1200
View 9 Replies
View Related
Sep 10, 2011
Okay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies
View Related
Jan 11, 2012
I just got an E1200 router and connected wired to my win 7 machine, Im clocking in the single digit ranges (~8 mbs) download but on my dusty old win xp laptop wireless, Im getting 20 mbs (max speed from isp 20 mbs). Wife's Mac laptop wireless, same speed. What is going on? I updated the firmware, tried altering some settings based on other entries here suggested (WPA-personal, channel to "6") but no effect.
View 2 Replies
View Related
Oct 31, 2012
I just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.
View 4 Replies
View Related
Mar 25, 2013
I have the E1200 and since I installed this router, the wireless download speed on my iPad and iPhone has been only around 4 to 5 Mbps when my other wireless devices could get to 7 Mbps and ethernet gives close to 10 (my ISP gives 10 Mbps max).I know many people experience slow download and normally disabling the WMM would solve the issue. But this doesn't work for me and I've made sure i'm on the latest firmware.
View 5 Replies
View Related
Feb 23, 2013
For some reason I can no longer make Wi-Fi calls with my E1200 router. I have checked with my ISP and T-mobil. They both tell me that everything on their respective ends is working correctly. The only piece of the equation is the router.
View 5 Replies
View Related
Aug 14, 2012
The wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
View 5 Replies
View Related
Apr 15, 2012
I recently purchased an E1200 to replace a broken router. I have had good experiences with this model in the past which is why I bought it. However this has not been so pleasant. For some reason the internet connection over wifi is INCREDIBLY slow. I don't know why. It is fast when connected via ethernet to the router. I changed the MTU on the router to 1400, I set the wireless width to 20MHz and the channel to 11. I set security to WPA2. And yet it is still very very slow. It's not a matter of how many users are on the network; I live in a house with five other people and it's slow regardless of whether everybody's home or nobody is home. It's like this on Macs, PCs, phones and even the Xbox 360. I just did a speed test. Wired was about 14MBps down, wireless was around .7MBps down. I simply cannot comprehend this discrepancy. The old router was very unreliable in terms of connectivity but at least it was always fast. And my laptop is fast at my mom's house where she has an E1200. I use a MacBook Pro from 2009 but like I said,this seems to be affecting everybody in the house regardless of hardware.The modem is a Ubee modem from Comcast. I'd upgrade it to a SURFBoard but my landlord controls all the utilities and I'd rather not have to explain to him how to call Comcast and tell them to register the modem's serial number to the account or whatever.
View 2 Replies
View Related
Apr 9, 2012
Router: E1200 2.0.02 build 3 Feb 15, 2012
These symptoms are stumping me:
WiFi drops 80% packets from new computers (Win7, IPv4 andIPv6 enabled) to reliable internet hosts. WiFi is OK (0% loss) from new computers to E1200 itself (ping E1200 IP address).Old computers, mobile devices, and wired are OK to reliable internet hosts.Basic Wireless Settings are Mixed, Auto Channel Width. Wireless Security is set to WPA2/WPA Mixed Mode. Guest Access enabled.
View 3 Replies
View Related
Jun 12, 2012
I just bought the Cisco E1200 about two weeks ago to replace an older Linksys non wireless router. With my old Linksys, I had an Acess Point installed, a trendnet TEW-638APB. Now that I have the new Cisco E1200 which itself is wireless, I'd like to add my TrendNet Access Point to the netowork and extend the wireless range. However the place in the house I want to put it does not have any CAT-5 cable running to it so I'm trying to set up a bridged connection between the two. I'm a bit new to netoworking stuff but I catch on pretty quick. I've been doing research on it all day between the TrendNet AP and the Cisco E1200 but I'm still a little lost. I've got WDS enabled on the TrendNet AP and have the first MAC address set to the Wireless MAC address of the E1200 but I don't get what to make the next three MAC address. Somone told me to make all 3 of them 00:00:00:00:00:00. Is that correct?
I also have both the E1200 and the TrendNet AP set to the same channel, both are on a 20Mhz channel width, Both have the same SSID though I'm pretty sure that doesn't matter in the long run from what I've read. Also, no incryption on either (no need for it out here).So I guess I'm just wondering how do I use the E1200 as a Wireless Base Station? If that's what it's called? I have upgraded the firmware of the E1200 from 1.0.00 to 1.0.03 but that didn't change anything in regards to seeing an option for a bridging mode or anything. Other than that I'm not sure what else to do.
View 8 Replies
View Related
Jan 6, 2013
I have an E1200 model 1 router. I've owned it for over a year and it's given me no problems until now...Hardwired ethernet connections work fine, but the wifi no longer works consistently. I have several wireless-N wifi devices that either cannot connect to the router at all (they present an error message), or do connect but will not load anything over the connection, or will load web pages very very slowly and then suddenly drop the connection.When I go to the DCHP client table, I see all of my ethernet connections but it does not show any wifi devices, even if the WiFi device is showing a connection to the router.The wifi connection is secured via WPA2 Personal.I have tried changing channels to one that was not congested with any other nearby routers. I have also tried a 30-30-30 factory reset. I am updated to the latest firmware version (1.0.03). I am sure I am entering the correct pass phrase to connect over WPA2. All of my wifi devices are confirmed to be wireless-n, not g or b.
View 7 Replies
View Related
Jul 24, 2012
We have a Linksys E1200 modem and I have been having problems with keeping my son from using the wireless interenet. I did change the password and that worked for about 24 hours and then he was able to get onto it again. He has a nintendo dsi and he is smart enough to figure out how to dismantle any parental controls on his gaming device. I think that he resets the modem in order to get back onto the internet in order to use his gaming device. Someone told me that you can register each item individually in order to keep kids from using it but I have no idea as to how this works. We have two iphones, a lap top, and two tablets.
View 7 Replies
View Related
Jun 22, 2011
My newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
View 9 Replies
View Related
Feb 12, 2012
1. I set a router admin password different from WiFi password(passphrase).
2. I run my Cisco Connect app and it asks me to change my router admin password.
If I don't change it - I can not use Cisco Connect app.
If I provide my WiFi password then it changes my router admin password.
Maybe it was done to have a "simple" solution - 1 password for everything. But maybe its a bug because router admin password should be different from WiFi password fro security reasons.
View 5 Replies
View Related
Aug 19, 2012
Buy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
View 3 Replies
View Related
Aug 23, 2007
I updated the Firmware...then the WRT54GC can't work now,it's power led green and red always,I can't ping 192.168.1.1 via wired or wireless.wireless led shutdown.my laptop can't find any wireless network.
View 9 Replies
View Related
May 2, 2012
I recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.
View 7 Replies
View Related
May 1, 2013
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies
View Related
Jul 13, 2012
I have Linksys configured with IP 192.168.0.x and my local network ip 192.168.1.x have firewall connected to Adtrans box that gives us internet access via T1 line and other port is connected to the switch. Wireless router is connected to the switch using internet port.I can connect to wireless using iphone but emails don't work when connected to wireless. I tried to connect laptop to wireless is does not connect.
View 9 Replies
View Related
Jan 5, 2013
buying a wireless router to use as a wifi extender as the signal is weak upstairs. At the moment my pc upstairs is connected by ethernet cable, I'm thinking of connecting a router upstairs to this ethernet cable to have good wifi upstairs. And my pc does have wifi so I will use that.
View 1 Replies
View Related
Dec 22, 2012
I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies
View Related
Jun 5, 2012
I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies
View Related
Aug 12, 2012
Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies
View Related
May 1, 2013
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies
View Related
Nov 7, 2011
I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies
View Related
Jan 4, 2012
Is it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?
View 3 Replies
View Related
Oct 23, 2012
Bought a new Samsung tablet and a Cisco wi fi router. But I don't have the CD drive to activate the wi fi router. I am using the Cisco linksys E1200.
View 1 Replies
View Related
