I just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.
View 4 Replies
I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies View RelatedI've got a problem with my new Linksys E1200 (v1) router. It cuts the bandwidth of my PPTP connection with ISP (which is 50 Mbps) down to about 12 Mpbs. My firmware is the latest one (v1.0.03 build 4). I've done some reading and found out that it's pretty common problem between Linksys E-Series routers and ISPs that use PPTP/L2TP.
View 4 Replies View RelatedI received a Linksys E1200 Wi-Fi Router for Christmas. I inserted the Setup CD into my iMac, running OS X version 10. 8. 2. I clicked on setup and a window opened with the message "Unsupported operating system".At this point I don't plan to use the Wi-Fi for the computer, but I do need to connect the ethernet cable to the router, then to my computer.I will be using Wi-Fi for my iPad. In that case, I have no instructions on how to set up the router for my iPad. Will this Wi-Fi router work or will I need a router compatible with OS X version 10.8.2?
View 1 Replies View RelatedMy Wi-Fi keeps on freezing and I have to unplug it all the time. I have the e1200
View 9 Replies View RelatedMy 1200 v 1.0 was working fine until I tried to link a wireless internet camera. Apparently I screwed something up in the setup such that I've lost my WiFi connection to my laptop and one wireless desktop. Fortunately my wired connection still works. I've carefully tried to restore my system following the online procedure and while the setup looks OK it doesn't link. In the process I have reset the router to the factory setting several times and have installed the latest firmware version. I contacted Linksys support and using remote diagnosis they reached a point where they said that something was wrong with my computer and to investigate further there would be a fee charged. I balked at that since I had tried the setup from several different wired Window 7 and XP computers.
View 9 Replies View RelatedOkay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies View RelatedI just got an E1200 router and connected wired to my win 7 machine, Im clocking in the single digit ranges (~8 mbs) download but on my dusty old win xp laptop wireless, Im getting 20 mbs (max speed from isp 20 mbs). Wife's Mac laptop wireless, same speed. What is going on? I updated the firmware, tried altering some settings based on other entries here suggested (WPA-personal, channel to "6") but no effect.
View 2 Replies View RelatedI have the E1200 and since I installed this router, the wireless download speed on my iPad and iPhone has been only around 4 to 5 Mbps when my other wireless devices could get to 7 Mbps and ethernet gives close to 10 (my ISP gives 10 Mbps max).I know many people experience slow download and normally disabling the WMM would solve the issue. But this doesn't work for me and I've made sure i'm on the latest firmware.
View 5 Replies View RelatedFor some reason I can no longer make Wi-Fi calls with my E1200 router. I have checked with my ISP and T-mobil. They both tell me that everything on their respective ends is working correctly. The only piece of the equation is the router.
View 5 Replies View RelatedThe wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
I recently purchased an E1200 to replace a broken router. I have had good experiences with this model in the past which is why I bought it. However this has not been so pleasant. For some reason the internet connection over wifi is INCREDIBLY slow. I don't know why. It is fast when connected via ethernet to the router. I changed the MTU on the router to 1400, I set the wireless width to 20MHz and the channel to 11. I set security to WPA2. And yet it is still very very slow. It's not a matter of how many users are on the network; I live in a house with five other people and it's slow regardless of whether everybody's home or nobody is home. It's like this on Macs, PCs, phones and even the Xbox 360. I just did a speed test. Wired was about 14MBps down, wireless was around .7MBps down. I simply cannot comprehend this discrepancy. The old router was very unreliable in terms of connectivity but at least it was always fast. And my laptop is fast at my mom's house where she has an E1200. I use a MacBook Pro from 2009 but like I said,this seems to be affecting everybody in the house regardless of hardware.The modem is a Ubee modem from Comcast. I'd upgrade it to a SURFBoard but my landlord controls all the utilities and I'd rather not have to explain to him how to call Comcast and tell them to register the modem's serial number to the account or whatever.
View 2 Replies View RelatedRouter: E1200 2.0.02 build 3 Feb 15, 2012
These symptoms are stumping me:
WiFi drops 80% packets from new computers (Win7, IPv4 andIPv6 enabled) to reliable internet hosts. WiFi is OK (0% loss) from new computers to E1200 itself (ping E1200 IP address).Old computers, mobile devices, and wired are OK to reliable internet hosts.Basic Wireless Settings are Mixed, Auto Channel Width. Wireless Security is set to WPA2/WPA Mixed Mode. Guest Access enabled.
I just bought the Cisco E1200 about two weeks ago to replace an older Linksys non wireless router. With my old Linksys, I had an Acess Point installed, a trendnet TEW-638APB. Now that I have the new Cisco E1200 which itself is wireless, I'd like to add my TrendNet Access Point to the netowork and extend the wireless range. However the place in the house I want to put it does not have any CAT-5 cable running to it so I'm trying to set up a bridged connection between the two. I'm a bit new to netoworking stuff but I catch on pretty quick. I've been doing research on it all day between the TrendNet AP and the Cisco E1200 but I'm still a little lost. I've got WDS enabled on the TrendNet AP and have the first MAC address set to the Wireless MAC address of the E1200 but I don't get what to make the next three MAC address. Somone told me to make all 3 of them 00:00:00:00:00:00. Is that correct?
I also have both the E1200 and the TrendNet AP set to the same channel, both are on a 20Mhz channel width, Both have the same SSID though I'm pretty sure that doesn't matter in the long run from what I've read. Also, no incryption on either (no need for it out here).So I guess I'm just wondering how do I use the E1200 as a Wireless Base Station? If that's what it's called? I have upgraded the firmware of the E1200 from 1.0.00 to 1.0.03 but that didn't change anything in regards to seeing an option for a bridging mode or anything. Other than that I'm not sure what else to do.
I have an E1200 model 1 router. I've owned it for over a year and it's given me no problems until now...Hardwired ethernet connections work fine, but the wifi no longer works consistently. I have several wireless-N wifi devices that either cannot connect to the router at all (they present an error message), or do connect but will not load anything over the connection, or will load web pages very very slowly and then suddenly drop the connection.When I go to the DCHP client table, I see all of my ethernet connections but it does not show any wifi devices, even if the WiFi device is showing a connection to the router.The wifi connection is secured via WPA2 Personal.I have tried changing channels to one that was not congested with any other nearby routers. I have also tried a 30-30-30 factory reset. I am updated to the latest firmware version (1.0.03). I am sure I am entering the correct pass phrase to connect over WPA2. All of my wifi devices are confirmed to be wireless-n, not g or b.
View 7 Replies View RelatedWe have a Linksys E1200 modem and I have been having problems with keeping my son from using the wireless interenet. I did change the password and that worked for about 24 hours and then he was able to get onto it again. He has a nintendo dsi and he is smart enough to figure out how to dismantle any parental controls on his gaming device. I think that he resets the modem in order to get back onto the internet in order to use his gaming device. Someone told me that you can register each item individually in order to keep kids from using it but I have no idea as to how this works. We have two iphones, a lap top, and two tablets.
View 7 Replies View RelatedMy newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
View 9 Replies View RelatedI recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.
I have Asus EEPC Seashell/ 1015PEM netbook. The wi-fi connects only near/ so close to the wireless router with full signal. Just next room, blocked by a wall it disconnects, but full signal still exists. Is it anything to do with driver or hardware incompatibility- netbook has 802.11n adapter. Wireless router/DI624+ is 802.11g.
View 8 Replies View RelatedWhen I have a computer directly connected to the Cable Modem I get 9.84MB Down and 1MB Up. When I put it behind the ASA 5505 with policing on the interface, I only get 4MB Down and 660Kb Down.What I'm wanting to do is setup this up to enable my VoIP to have a higher priority and shave 128kon both the Up/Down for the VoIP traffic. I also want to make sure I don't exceed the inbound and outbound thresholds.I''m using a 5505 Security Plus?
View 3 Replies View RelatedI have two Catalyst 3560 series switches with a 100Mb Ethernet microwave link and a 250Mb Ethernet microwave link between them. Can the switches be set up to make full use of the added bandwidth (350 Mb).
View 3 Replies View RelatedI just got a new E4500 and plugged a blank 2TB drive into it (Windows shows it is formatted NTFS) which was originally plugged into my WRT-610. I'm moving my media files and when it hits a 50+GB video it reports that there is not enough space to move the file. Smaller files are moving just fine.
View 4 Replies View RelatedI recently bought an AE1000 wireless adaptor, but I have run into a problem.The range on the device is very low, as the only way to get full signal is when the router and device are right next to each other.I have read that this could be due to the device operating on 5.0Ghz frequency, and that this setting is changed through the Cisco Connect software. This software was not in the Setup CD, and the online installer did not install the software either.
View 4 Replies View Relatedi have a little annoying problem with my E4200. V1 with the latest 04 fw. It seems, that after many hours of downloading at full speed (only one torrent at a time) the speed goes down, and up again, and becoming unstable. My max download speed is 1.5 Mb/s, and it can drop from that, to 50 kb/s, and then up again. and i have no internet access when that happens, but it only last 10-20 seconds and then its back again. Sometimes i get that yellow warning sign on the taskbar which says "No Internet Access" but not always.
Seems like its happening after many hours of downloading at full speed. im on the latest firmware, have tried different channels, 20 Mhz only on Channel Width, different names on the 2.4Ghz and 5Ghz channels.. i use the 2.4Ghz channel btw. Otherwise its stable, and i have had no problems while gaming online.
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies View RelatedI just acquired a used E2100 from an auction, when I plug it in I see an "Unnamed Network" with full bars in wireless, but can't connect since I don't know the ssid/password.When connecting with cable, with ipconfig I get a 10.10.10.108 ip, the gateway is at 10.10.10.99. Yet I also cannot access it.I have tried the reset button at the bottom, holding it for over a minute, pressing it quickly, holding it for 30 seconds, holding it and unplugging + replugging the router, but nothing is working.I have also tried the CD that comes with it with cable and with wifi only, but it does not find the router. I have deleted my default wireless network settings, had my wifi on, was not connected to any networks, yet the CD could not find the router.When router is on, the WIFI led blinks around once a second, while the LAN led blinks randomly like it should.
View 3 Replies View Relatedmy router has all the lights on that it's always had. I use the wi fi for my iPhone,iPod, and laptop. On all of then I'm able to to search and find my connection and connect to it , but it's shows I'm connected with full signal but my internt just worn work . I can't connect to the internt on none of the devices, also if I connect the ethernet from my modem to my router then my routers ethernet to my pc my pc's internt won't work.
View 2 Replies View RelatedJust got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies View RelatedI have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T. I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials. If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg. I have 6 cat-e ethernet cords everywhere. I do have 2 switches but have tried to unplug those to see if any difference
View 1 Replies View RelatedI have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies View RelatedI have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies View RelatedSetting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies View RelatedI purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies View Related
