Linksys Wireless Router :: EA3500 - Not Getting Full Speed When Connect Pc Directly To Modem
Sep 1, 2012
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies
ADVERTISEMENT
Jul 2, 2012
I recently purchased the router and got the CCC firmware on. It works fine for a while but then I can't connect to the router using my PC unless I log using the remote credentials. Generally if this were the case I wouldn't care but when I do it that way I can't run the speed test. After I reboot the router it works fine again, for a while.
For some reason, it doesn't detect my PC as being connected directly although my PC is connected by wire, directly to the router.
View 4 Replies
View Related
Dec 21, 2011
I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T. I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials. If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg. I have 6 cat-e ethernet cords everywhere. I do have 2 switches but have tried to unplug those to see if any difference
View 1 Replies
View Related
Apr 2, 2013
I have a Netgear WNDR3700v2 that I was very happy with until I got a nest thermostat. Apparently it is an unsupported router and I had to change it. I bought a E2700 since it was supported, but I'm having a huge dilemma...
If I connect the linksys directly to the modem, I'm not getting an internet connection. I've released and renewed IPs to no avail..
but if I hardwire the linksys to the netgear, I do get a good solid internet connection. problem is, I have no need for 2 routers setup on top of each other.
basically, I dont understand why linksys is not able to connect directly to the modem. yet it gets solid connection hardwired through another router.
I'm using Comcast and in south FL. it's a motorola surfboard modem
View 5 Replies
View Related
Mar 8, 2013
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies
View Related
Aug 12, 2012
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
View 14 Replies
View Related
Jan 25, 2013
I bought a EA 3500 router and my speed is going only half the speed it was without the router.I have charter 100 meg internet, and a alienware Pc with a gigabit card.I wa going 100 megs and now I am at 38-50.I have tried hard reset with the bottom button, I have turned off all firewalls, I have changed my MTU to 1400 and 1500, I have went to speedguide.net and ran a optimizer., I have tried just about everything I can think of. firmware is up to date.
Is there anything I am missing, or am I not going to get these speeds with this router, I was told when I bought it, it was what I needed, Was I duped?, or is there just some setting i need to fix i am not aware of?
View 1 Replies
View Related
Dec 5, 2012
I have had a EA3500 router in front of a 3Mb ADSL connection for about 6 months. This delivered essentially the same WAN performance as the WRT54G (v5) I replaced with it. Either router would get 2.4-2.8Mbps through a variety of speed test sites, inlcuding the CCC builtin speed test.I upgraded to a 10Mbps cable internet connection today, but the EA3500 won't deliver any more speed than with the old ADSL connection. The reason I am blaming the EA3500 is that if I plug my computer directly into the cable modem, I get a solid 9.9Mbps down/0.99Mbps up, which is exactly how my line is provisioned. With the router in place and active, I get the same slow WAN connection, 2.8-2.9MBps, whether using a PC connected with GigE, a PC connected via Wireless-N, or with an iPhone. This all implicates the EA3500's WAN connection.
Is there anything that can be done do let the EA3500 work properly? I upgraded my firmware today in hopes that that would change something. But, I get the same speed with the latest firmware (1.1.39.145204) as I did with the previous version. Speed across my wired LAN is excellent; I can sustain 70MB/sec from my PC to my NAS. It's only the WAN connection that is performing poorly.I can downgrade to the non-CCC firmware if that would make a difference; would it?
View 4 Replies
View Related
Jun 30, 2012
I did a simple speed test comparing my EA3500 and Linksys WRT54GL. I used DSL Reports for the test. I was quite shocked and am wondering if the difference is due to the poor wireless driver in the Classic firmware that was updated in the Cloud firmware. Here are my numbers: EA3500, Classic firmware Download average 475 kb/s Upload average 725 kb/sLinksys WRT54GL Ver 1.1 (latest firmware) Download average 3250 kb/s Upload 725 kb/s
Needless to say I have gone back to my trusty WRT54GL until Cisco decides if it will update the Classic firmware and give us 2nd class Cisco customers the same hardware the 1st class Cloud customers have. Time will tell.
View 9 Replies
View Related
Aug 20, 2012
i have a little annoying problem with my E4200. V1 with the latest 04 fw. It seems, that after many hours of downloading at full speed (only one torrent at a time) the speed goes down, and up again, and becoming unstable. My max download speed is 1.5 Mb/s, and it can drop from that, to 50 kb/s, and then up again. and i have no internet access when that happens, but it only last 10-20 seconds and then its back again. Sometimes i get that yellow warning sign on the taskbar which says "No Internet Access" but not always.
Seems like its happening after many hours of downloading at full speed. im on the latest firmware, have tried different channels, 20 Mhz only on Channel Width, different names on the 2.4Ghz and 5Ghz channels.. i use the 2.4Ghz channel btw. Otherwise its stable, and i have had no problems while gaming online.
View 7 Replies
View Related
Jul 29, 2012
It has been 4 months since I upgraded my internet connection from 2 mbps to 4 mbps.I have called the ISP but they say the speed is okay.When I open 192.168.1.1 it says(datas shown below),but everytime i download something or measure my internet connection it never goes more than 2 mbps (max 230 kbs download[CODE]
View 3 Replies
View Related
Dec 2, 2012
With my old routeur (wrt310n) I used to be able to limit the wireless speed.I cant seem to find the option with my new routeur, EA3500.did they remove the option ?
View 1 Replies
View Related
Sep 2, 2012
I used the CD to set up my new EA3500 with my Wild Blue Satellite internet modem.An IPhone or IPad can connect and work like a charm, remaining rock solid at all times. Windows 7 on the other hand, will work and then lose connection to the internet. The PC appears to remain connected to the EA3500, but the connection between the EA3500 and modem appear to be lost. I can click on the bar Icon at the bottom and it shows everything to be fine. I click on disconnect and then wait a few seconds and click on connect again and it works for a few minutes before having to do it again. When I look at the router properties the CD set it up for DHCP.
View 2 Replies
View Related
Feb 20, 2013
I want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
View 6 Replies
View Related
Feb 9, 2011
So I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
View 1 Replies
View Related
Jan 24, 2013
Can i connect my 3g USB modem to my dlink router directly through the usb port.
View 10 Replies
View Related
Jul 29, 2012
Can not connect computer to Cisco Connect -.Receive error msg 82BD0305. Reset to EA3500 to default and reinstalled software.
View 8 Replies
View Related
Feb 15, 2013
setup an external hard drive with music on on the usb port on my EA3500 and actvated ftp but I cant access it from the net.
View 1 Replies
View Related
Jun 24, 2012
I am unable to connect a printer using the USB port on my new Linksys EA3500 router.
I followed the directions here: Support Page , but my verison of Cisco Connect does not have the option to "connect a USB printer".
I am on a macbook pro running OSX 10.7.4 and my verison of Cisco Connect is 1.4 (12005.2). My router's firmware version is 1.0.30.126544. A screenshot of what I see after clicking "add a device" in Cisco Connect is below. The printer is an HP DeskJet F4280.
View 9 Replies
View Related
Aug 14, 2012
After using the newest firmware for CCC, I've found it is very convenient, but only in some ways. Now, I think I find it is uncomfortable, very disappointed and waste lot of times. Each time I try to access to CCC, it took me like 5 mins to access the web page. I understand ciscoconnectcloud.com is use when you are outside of your home network, but when I access it directly from my home (local IP), why should I need to connect via a CCC(?) I want a local connect to my router which is a faster access than via a server.
Sometimes, connect via an IP of the router, it say can't connect because of internet connection down, but actually I can still access internet except access my own router. I like the easy setup of CCC but maybe I need to switch back to non-CCC?
View 9 Replies
View Related
Apr 30, 2012
I bought a new router today because my WRT54GL was giving me some fits. I purchased an EA3500 and I'm using an EA2500 adapter on the desktop since the router can't reach it via ethernet. Some of my early troubles with this combo began with not being able to test upload bandwidth. It would just time out and give an error via the built in Cisco (OOKLA) utitliy and through speedtest.net after which, the network would show no internet access and I'd have to reset the adapter. After trying to troubleshoot that issue it grew into zero internet access for my desktop however my Nexus would have wifi access without issue. If I'd startup in safe mode with networking I'd have net access shortly and then it would quit about 30 seconds after startup. I've tried uninstalling all drivers for the wireless NIC and the Cisco Connect software while doing everything manually but nothing changes. This PC simply won't gain internet access with the EA3500 or even allow me to access the router through the default gateway IP. I've since put the WRT45GL back in place and I have access again with my EA2500 adapter. I should note that with the EA3500 in place, if I disconnected from my wireless I couldnt see any networks until I unplugged the adapter and reinserted it into the USB port (i've also tried many different ports). I've named the SSID's of the two routers differently, tried a manual setup of the wifi, tried the CD setup, the wifi protected setup, no security, and WPA2 to no avail. I can't seem to get the EA2500 adapter and the EA3500 router to get along. I'm running W7 x64 Pro.
View 6 Replies
View Related
Mar 19, 2013
I have an HP Veer Webos phone. Since I upgraded to an EA3500, I haven't been able to connect my phone to the network wirelessly. Today I temporarily installed a WAP54g on the network, and I am able to connect the Veer via the WAP. I spent 45 minutes chatting with Cisco Support today, but didn't resolve the problem. I believe I have the same situation with an HP Touchpad, but can't say the problems are identical, since its battery is down right now.
[code]....
View 7 Replies
View Related
Mar 30, 2013
Just installed a Linksys N750 (EA3500) router (WAN - LAN setup). I settled both band networks : 2.4 Ghz and 5Ghz with different SSID and different WAP2/WAP personal mixt. WHile some devices will show both networks correctly, I'm facing issues with the 5Ghz band and wonder if this is sigh of some kind of failure:
- while my iPad offered both signals and let me set the 5 Ghz band, it is showing weak signal and stall on loading webpages; as soon as I instead put it on the 2.4Ghz band, (standing at same location of course), everything runs smoothly, excellent signal.
- I have a Mac Mini and PS3 side by side same location. The Mac Mini seems to works flawlessly under both bands, 2.4 or 5 - excellent signal. However, the PS3 fails its connexion test and states that signal is not perceptible on the 5Ghz. But connect as a snap on the 2.4 Ghz band.
- Got on and off 5Ghz signal on a laptop; connected to 2.4Ghz, everything runs perfect.
- iPhones 4S : I don't even see the 5Ghz SSID, but I get both the 2.4 and Guess account..So I'm tempted to conclude that some devices just can't follow the pace (??) to connect on 5Ghz..
View 4 Replies
View Related
Aug 12, 2012
I bought a new router 4 days ago, I think. And been trying to figured out how to connect to Internet... Well, my Wi-Fi is connected perfectly but is not connected to Internet because it has no access to Internet. I can't figured it out how. I tried for hours per days. A friend of mine checked in my computer.My router is Linksys EA3500. I am truly thinking about sending it back to store and get a full refund then buy another brand of router... for my iPad to able to surf, to play, to e-mail and everything.
View 9 Replies
View Related
Jul 26, 2011
I have external hard drive connected to E3000. It is formatted as NTFS and working fine. However if I disconnect from router and connect to PC usb port directly, I get a message that hard drive needs to be formatted.
View 2 Replies
View Related
Dec 22, 2012
I have full signal strength but I can't connect to the internet from any device. Internet works fine when connected directly to devices. Devices will show an IP address but will not connect to the internet. The first router worked fine for about a year and did the same thing so I replaced it but now after 1 month, this router is doing the same thing!
View 1 Replies
View Related
Jan 19, 2013
I've just bought an EA3500 router. I have made all the setup, intsall Linksys smart wifi..Now that all is done, I try to install my printer but it didn't work..When I try to connect the printer cias Cisco VSUB application, the application try to connect the printer but the application is stuck at this step..After making a search on the forum, I found that somebody have uninstall the printer, re-install the printer driver and it work for him but not for me...
View 9 Replies
View Related
Feb 16, 2013
All of us connect effortlessly to wifi via the EA3500. All of us, however, also have iPhones, and yet none of us can get on wifi with our iPhones. Apple insists the problem is on the Cisco side, not the Apple side, and I have to agree with them because all of the iPhones connect effortlessly to wifi everywhere else it is available. I tried contacting Cisco support, but they wound up telling me that if I paid them they might be able to assist, since the router is outside the warranty period. (I tried explaining to them that I didn't know about the extent of the problem until 10 days ago My wife simply uses her mac; none of my daughters lives here and only one of them had an iPhone until ten days ago when I purchased the other ones. But that was to no avail.) Why no one can get on wifi with iPhones when they can, simply and effortlessly, with the PC, the iPad, and their macs?
View 5 Replies
View Related
Oct 24, 2012
When the ethernet cable is plugged directly into my laptop i can input my user name and password and connect directly without a problem. But as soon as i plug the cable into the router, the activity lights turn off like its not plugged in on the other end...which it is. So when going through the setup process, both using the cd and inputting the information on the web based setup. It does nothing, the automatic setup says the cable isnt plugged in. When using the browser setup i can click connect as many times as i want and it does nothing but say disconnected.
View 9 Replies
View Related
May 8, 2012
can i connect the ea3500 to 4 bay enclosure: [URL] it is connected through only 1 usb cale inside the enclosure i have 4 2TB western digital drives?
will i be able to see the 4 drives on my network?
View 4 Replies
View Related
Aug 22, 2012
I wanted to connect to the internet so plugged the same cable into my laptop (running 7) [code]...
View 3 Replies
View Related
Sep 20, 2012
I bought an EA3500 because I found that I did not need the more expensivbe router. The problem that I have now is when I sign in to Cisco Connect Cloud both the old and the new router show up. I would like to remove the old router from the list. The old router shows as:CiscoA3518 [offline]
View 6 Replies
View Related
Jul 1, 2012
I just purchased an EA3500 because I absolutely need guest access. I set everything up through the Cisco Connect application on the CD and all was well. I figured it's time to get into the whole cloud connect app thing, as this is why I chose this router over another but after creating the account and activating through email, I constantly get the message that I need to associate my router with my account.The PC I am using is directly connected to the router through a cable. I'm not sure what else I am to do at this point. The content of the entire message basically is telling me to head to [URL] with the PC connected to the router that I want associated and to follow the directions.
1. There are no directions... I get that message every time.
2. I've tried rebooting the router and then logging in to the website - that gives me a message saying there's no router detected, meaning that somehow the site IS detecting the router, I just somehow haven't associated it.
View 1 Replies
View Related