Linksys Wireless Router :: EA3500 Classic Speed Test?
Jun 30, 2012
I did a simple speed test comparing my EA3500 and Linksys WRT54GL. I used DSL Reports for the test. I was quite shocked and am wondering if the difference is due to the poor wireless driver in the Classic firmware that was updated in the Cloud firmware. Here are my numbers: EA3500, Classic firmware Download average 475 kb/s Upload average 725 kb/sLinksys WRT54GL Ver 1.1 (latest firmware) Download average 3250 kb/s Upload 725 kb/s
Needless to say I have gone back to my trusty WRT54GL until Cisco decides if it will update the Classic firmware and give us 2nd class Cisco customers the same hardware the 1st class Cloud customers have. Time will tell.
View 9 Replies
ADVERTISEMENT
Nov 6, 2011
I have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies
View Related
Jan 25, 2013
I bought a EA 3500 router and my speed is going only half the speed it was without the router.I have charter 100 meg internet, and a alienware Pc with a gigabit card.I wa going 100 megs and now I am at 38-50.I have tried hard reset with the bottom button, I have turned off all firewalls, I have changed my MTU to 1400 and 1500, I have went to speedguide.net and ran a optimizer., I have tried just about everything I can think of. firmware is up to date.
Is there anything I am missing, or am I not going to get these speeds with this router, I was told when I bought it, it was what I needed, Was I duped?, or is there just some setting i need to fix i am not aware of?
View 1 Replies
View Related
Feb 18, 2013
I've a problem with the internet speed of my ADSL line(20Mega). Now I've the following components: D-link DSL-320 B (modem)+Cisco Linksys EA6500. If I start a Speed test the result its only 4M in download, while i remove the router and i connect my Pc directly to modem, the speed test results its 13-14M.
View 3 Replies
View Related
Dec 5, 2012
I have had a EA3500 router in front of a 3Mb ADSL connection for about 6 months. This delivered essentially the same WAN performance as the WRT54G (v5) I replaced with it. Either router would get 2.4-2.8Mbps through a variety of speed test sites, inlcuding the CCC builtin speed test.I upgraded to a 10Mbps cable internet connection today, but the EA3500 won't deliver any more speed than with the old ADSL connection. The reason I am blaming the EA3500 is that if I plug my computer directly into the cable modem, I get a solid 9.9Mbps down/0.99Mbps up, which is exactly how my line is provisioned. With the router in place and active, I get the same slow WAN connection, 2.8-2.9MBps, whether using a PC connected with GigE, a PC connected via Wireless-N, or with an iPhone. This all implicates the EA3500's WAN connection.
Is there anything that can be done do let the EA3500 work properly? I upgraded my firmware today in hopes that that would change something. But, I get the same speed with the latest firmware (1.1.39.145204) as I did with the previous version. Speed across my wired LAN is excellent; I can sustain 70MB/sec from my PC to my NAS. It's only the WAN connection that is performing poorly.I can downgrade to the non-CCC firmware if that would make a difference; would it?
View 4 Replies
View Related
Aug 18, 2007
I have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ). I did a ping test and the results are
View 2 Replies
View Related
Feb 15, 2013
When I try the Speed Test on my EA6500 I am getting the following message. "The license for this Speed Test has expired. Please contact the webmaster of this site to let them now.".
View 7 Replies
View Related
Sep 1, 2012
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies
View Related
Dec 2, 2012
With my old routeur (wrt310n) I used to be able to limit the wireless speed.I cant seem to find the option with my new routeur, EA3500.did they remove the option ?
View 1 Replies
View Related
Dec 3, 2012
I installed an E1200 router today. It automatically upgraded the firmware to the latest when I did this. Everything went smoothly.
I connected my desktop wired and my laptop wireless. I ran three different speed tests: Xfinity, speedtest, and cnet. All three showed 25-35 Mbps download and 4-5 Mbps upload. That is what my old router had too. So far, so good.
I ran the speed test that came with the E1200 router. It showed 0.30- 0.66 Mbps download and 0.58 - 2.09 Mbps upload. Note the decimal points!
Bottom line: The E1200 seems to be working fine, except that its internal speed test seems to be broken, at least when testing from a wired machine.
View 2 Replies
View Related
Apr 12, 2013
Is classic firmware 2.0.37 for the EA4500/E4200v2 vulnerable? I see that the workaround is to use the latest Smart Wifi firmware. How soon can we expect to see a classic firmware update? [URL] Linksys quote taken from a random review that I found on Amazon below......The manufacturer commented on this review(What's this?) Posted on Jul 26, 2012 9:53:51 AM PDT Linksys says: (MANUFACTURER) Jason, Cisco Linksys plans to offer Software Updates to the EA Series router for customers who choose a local management option (including Cisco Connect/Classic). We will continue to provide Customer Care and deliver SW Updates to address Security, Critical Bugs and User Interface issues as required. Customers can comfortably stay with the local management option and Cisco will deliver continued support.
View 9 Replies
View Related
Aug 9, 2012
I may be replacing my e1550 soon and am looking at both the N750 and N900 class devices. While the EA3500/4500 seem to be a really good deal with a lot of bang for buck, I do have one concern...
As I have zero intention of ever using Cisco Cloud Connect, I would need to stick with the Classic firmware. While Cisco did quickly push out a solution to get the routers back to Classic after the initial Cloud Connect deployment fiasco, I cannot seem to find any commitment from Cisco to continue to support the classic interface (other than "“Cisco will continue to support both local and cloud management options for our customers.”). Even more disconcerting is that the current evidence seems to indicate that they are not. [code]
So, while I do understand that many of the updates have been Cloud Connect specific, some of these changes are in fact global/driver updates. As an example, according to the release notes, on June 25, 2012 the EA3500 CCC firmware v.1.1.38 (Build 138143) updated the WiFi driver, apparently the Classic never received this update.
View 9 Replies
View Related
Apr 6, 2013
I just ordered an EA4500. It should be here in a few days. After reading most of the 45 page Cloud Experience thread, I am leaning toward using the Classic Firmware. I have read the release notes but want your input:
1. Is the Classic Firmware stable or buggy?
2. Are there any features (besides cloud) that won't work? dual band? usb storage? dlna?
3. Where is user manual for Classic users?
View 2 Replies
View Related
Nov 18, 2012
Anyway to get the EA6500 back to Classic Style Firmware? I know they offered the roll back on the EA4500.
View 1 Replies
View Related
Feb 12, 2012
I currently have a 802.11 G router of 54mbps (its claims its a super G 108 mbps tough). My notebooks have 802.11 N built in. Im thinking of upgrading my router to a 802.11 N 300mbps.However, I know that this may be irrelevant unless I have a internet conection that can achieve such speeds. So how do I test my internet speed to see if G is bottlenecking?
View 4 Replies
View Related
Jun 7, 2012
I have upgraded my network service from 2M to 6M per month last week. But the network speed is not so satisfactory. I could hardly feeling its upgrading.Is there any trustful and accurate method or tool to test the network speed?
View 4 Replies
View Related
Feb 15, 2013
setup an external hard drive with music on on the usb port on my EA3500 and actvated ftp but I cant access it from the net.
View 1 Replies
View Related
Sep 7, 2012
For hours i tried to find info online of how to access QoS on EA3500 router. I cannot find it on the cisco connect cloud page.
View 1 Replies
View Related
Jul 18, 2012
System:
HP Pavilion dv7-6135dx Ent Pc Win7 Home Prem 64
Motorola Surfboard Modem
Linksys EA3500 Router
Netgear 10/100 24 port switch
my wife bought me this EA3500 for Father's Day this year. It's only been hooked up for a couple of weeks (we were in the middle of a move during Father's Day), but now I have no wifi on either band. My wife can no longer connect to it either. We have tried completely resetting it, we have reset the modem, the switch, laptops, everything. Still no wifi. It worked out of the box, but now we have nothing. Does HP needs a certain type of driver? Our iPhones show connected and surf the brower's and FB app with no issues while in wifi mode, but then again, I can pull the ethernet from the internet port and the phone's still show connected (good job, iOS).Cable from main splitter runs to basement where the modem is located. Modem ethernet feed up a wall to a wall plate where the router is. Router then feeds back to the switch. The switch then sends the IP throughout the house for the LAN lines, and the EA3500 feeds all of the wireless devices (used to). So, Cable box, modem, router, switch. Router is currently good for LAN only. I am connected to it via LAN right now, 2 feet from my laptop.
In connections:IPv4/IPv6 both "No Internet Access" (for IPv4, if you change a setting in the setup, it becomes "Internet Access" for about 3 seconds.)Media State: EnabledSpeed: Alternates between 72Mbps and 144Mbps
View 5 Replies
View Related
Feb 25, 2013
In my home network, I have a Synology. It has 10.0.123.123 as local IP address on my local network and it can be accessed by internet with the dynamic domain name.So when I'm home, I have to use 10.0.123.123 to access it, and when I'm away, I have to use trucmuche.diskstation.me.Would it be possible to configure the EA3500 to redirect the domain name "trucmuche.diskstation.me" to 10.0.123.123 when I use the domain name inside my home ?A friend told me that I had to configure "loopback" but I don't know how..
View 3 Replies
View Related
Jan 10, 2011
I did a network test with Passmarks Performancetest. I'm running a 10/100 network with all devices connecting at 100Mb. On Performancetest there are 2 tests to run for Network speed, TCP and UDP. The TCP speed test came back with an average 62000kbps (7.5Mb), and the UDP was 89000kbps (10.8Mb). As I'm running a 100mb network, shouldn't the results of been higher?
View 3 Replies
View Related
May 21, 2012
I have a cable lan connection for internet.i check speedtest.net for the results and it showed.9mbps download speed and .10 mbps upload speed.but when i download something i only get 0.45 mbps speed.Sometimes i get 9mbps but not often.But speedtest.net always shows my speed to be 9mbps.So that makes me guess , that there is actually 9 mbps available.now how do i utilize it.?
View 8 Replies
View Related
Jan 1, 2012
Have a localhost site to test PayPal IPN which apparently requires router configuration to use port forwarding (or redirection) to send TCP traffic on public port 80 to my test machines private IP at a specified port.
A typical configuration might look like this:
Router NAT Port Redirection Rule TCP Public Port 80 --> 192.168.1.2 (Port 8888)
Where can I find reference to this in online documentation and where do I put this instruction?
My Router is WRT54GS
View 1 Replies
View Related
Sep 7, 2012
The guest network on the router keeps going down. It can be seen but it cannot be connected to. Sometimes it works for a day or 2 and then it doesn't. I have to constantly babysit the network and it is entirely frustrating because the only fix is to reboot the router.I have tried factory resetting several times.I have tried re-flashing the fw.I'm using the non-CCC fw because CCC had way, way too many issues.These routers have been out for months and many people have been having issues and somehow Cisco doesn't see fit to work on firmware that stabilizes them at all? It's like, they release a router and then forget about it - the next batch comes along, often the same guts with a different shell and it's the same thing over again. I had a WRT610N and I said I'd never buy another Cisco after that but I broke my rule because of being lured by these "App enabled" features, which mind you have nothing at all over the competition since the CCC doesn't even work for most people.
View 9 Replies
View Related
Jan 22, 2013
I have a EA3500 wireless router with the new style (smartwifi) firmware. I've scoured the web admin interface and can't find any sort of 'status' page that would tell me the external IP. I've looked through the support docs but they only show how to find internal/local IP.
View 2 Replies
View Related
May 19, 2012
I have an EA3500. PPPoE connection. Can't seem to choose my DNS server (use Unblock-US) since the router insistently forces me to use the DNS from ISP.How can i work this around? I'm kinda tired of people asking me why i am changing the DNS. I want to change the DNS and that's final. It's a resource like any other and i want to use it.P.S: i tried most of the basic troubleshooting. I tried my old router back on and the DNS's works fine. I tried even conecting the old router re-routing the new one, and the other router manages the selected DNS's servers fine.
View 9 Replies
View Related
Jun 28, 2012
If someone has the original firmware for the EA3500 to copy. I need to downgrade my router after Cisco sabotaged it with their Cloud Connect. This will be the firmware you have right out of the box. Be sure you go into the Admin. section and Save a Copy before you ever connect to the Internet. Also Uncheck the Auto Updates box or you will be fed the Cloud Connect (and its amazing Terms Of Service).
View 6 Replies
View Related
Aug 7, 2012
Windows 7 64 bit / Linksys EA3500 / (2) FosCam F18910W IP Camera’s I just installed a new EA3500. (Should I have purchased the 4500)?I need to set up port forwarding to enable wireless use of the IP cams with my iPhone. I had this all set using my former router, but it died.how to to port forward this Linksys EA3500?
View 2 Replies
View Related
Mar 5, 2013
I have recently bought a cisco EA3500 router for my home network and i am pretty surprised to see that a router from the world leader in the networking domain cannot perform as expected.
The first problem i had was that the network (wired and wireless) was dropping from time to time for a couple of minutes with the power led of the router blinking. I turned off the log feature of the router and it seems that until now the problem is resolved.
Now, the second and, at least as annoying as the first, is that i have a 640gb usb hdd connected to the router, formatted NTFS. It seems that every now and then a file gets corrupted, that is, it is transformed into a folder! And it cannot be recovered without pulling out the hdd and using a 3rd parth software for file recovery.
I have the latest firmware. Should i switch back to the classic firmware instead of the "fancy" new one? I really need my files on that drive, so i cannot risk loosing them in this random manner.
View 4 Replies
View Related
Feb 16, 2013
I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)
View 9 Replies
View Related
Jun 24, 2012
I am unable to connect a printer using the USB port on my new Linksys EA3500 router.
I followed the directions here: Support Page , but my verison of Cisco Connect does not have the option to "connect a USB printer".
I am on a macbook pro running OSX 10.7.4 and my verison of Cisco Connect is 1.4 (12005.2). My router's firmware version is 1.0.30.126544. A screenshot of what I see after clicking "add a device" in Cisco Connect is below. The printer is an HP DeskJet F4280.
View 9 Replies
View Related
May 4, 2013
after updating to smart wi-fi I can't access the USB FTP or off network.Only way it's accessible is from the computer the router is attached to via network drive.FileZilla gives me this error....."Connection attempt failed with "ECONNREFUSED - Connection refused by server".I've reset the router same problem.
View 9 Replies
View Related
Aug 14, 2012
After using the newest firmware for CCC, I've found it is very convenient, but only in some ways. Now, I think I find it is uncomfortable, very disappointed and waste lot of times. Each time I try to access to CCC, it took me like 5 mins to access the web page. I understand ciscoconnectcloud.com is use when you are outside of your home network, but when I access it directly from my home (local IP), why should I need to connect via a CCC(?) I want a local connect to my router which is a faster access than via a server.
Sometimes, connect via an IP of the router, it say can't connect because of internet connection down, but actually I can still access internet except access my own router. I like the easy setup of CCC but maybe I need to switch back to non-CCC?
View 9 Replies
View Related
