Windows 7 64 bit / Linksys EA3500 / (2) FosCam F18910W IP Camera’s I just installed a new EA3500. (Should I have purchased the 4500)?I need to set up port forwarding to enable wireless use of the IP cams with my iPhone. I had this all set using my former router, but it died.how to to port forward this Linksys EA3500?
View 2 RepliesI have my router set up and life was good. i now want to forward a port. i go into apllications/gaming put the application name, the port i want to forward and click enable. Save changes and i get a changes save message. When the browser goes back to the applications/gaming screen no port shows as being forwarded. If i go to canyouseemenow.org the port shows as being closed.
View 3 Replies View RelatedHaving a devil of a time trying to forward a port on my router. Did everything instructions said, but it still doesn't work. What can I do.
View 2 Replies View RelatedI recently opened the ports used by Xbox Live: Port 88 (UDP)Port 3074 (UDP and TCP)Port 53 (UDP and TCP)Port 80 (TCP)I am able to use xbox live once these ports are opened but once they are enabled, I can not get wireless internet. The xbox is connected to the router with a cable so it isn't experiencing this probem. My laptop and phone are able to identify the network and join but there is no internet access.
If I disable these ports, everything goes back to normal.
Some routers are able to forward to broadcast directly by sending a port to 192.168.1.255, other's I've been able to trick by forwarding to 192.168.1.254 and then editing the arp table with 192.168.1.254 <-> ff:ff:ff:ff:ff:ff. Is there any way I can edit the arp table of the E4200? Is there a way to telnet in or get a console connection?
View 9 Replies View RelatedI encounter a problem setting up port 80 forwarding on WRT54g router.
Configuration:
- Numericable modem
- WRT54G router : portforwarding configured, accepting anonymous internet traffic, no DMZ, no port-triggering... in fact everything is fine except for ports 80/443
- Linux Ubuntu server + Apache2 listening *:80 and/or *:15001
1/ Situation 1: Apache listening on server's *:15001
-> Accessing from Internet (outside LAN) works very fine.
-> Portforwarding of router:15001 to server:15001 (TCP) works fine.
2/ Situation 2: Apache listening on server *:80
-> Accessing from Internet (outside LAN) FAILS.
-> Portforwarding of router:80 to server:80 (TCP) doesn't work. Diagnostic using the client machine's firewall tool showed the request doesn't get any return... no traffic back at all.
The system being fully operational when using port:15001 shows the problem does not come from server configuration.I still have to try a bypass of my router by plugging the modem directly on the server eth card.
-> If that works it would definitely prove the problem comes from the router, precisely the portforwarding feature as applied to port:80.
My guess is the following:
- As WRT54g router's remote administration interface is precisely set to listen 80/443 ports.
- As I still did not disable remote administration as I need it, but I will come to such extremities (very soon in fact as despair is gaining me
- Looks like WRT54g is unable to forward port 80 as this is it's remote administration port. You can set it up, but it just won't work, and there's no warning
Solutions?
- Disable remote administration? (will it work ? cause I would not risk to disable it for nothing...)
- Have remote administration litening on different ports than 80/443?
- Is my diagnostic correct ? (at least, does it seems to be...)
- (shall I get another device? Update to alternative firmware project?)
PS : I could be asked for ifconfig/netstats/hdw-fmw version, I would post later as I do not have access now.Looks like to me it is recurrent issue on WRT54g (maybe I'm wrong and just an **bleep** in LAN/WAN configuration which is highly possible)
I am trying to set up a web server behind WRT55AG router. I have read many forums where people are having the same problem, but none explain how to fix issue. The router will not forward any port to the server. Any attempt to access the server from outside my local network just brings me to the login screen of the router. I have tried port forwarding port 80 and 10080 and both do the same thing. Also, I have the firewall, remote management, and UPnP turned off
View 3 Replies View RelatedI'm using Cisco Connect Cloud to connect to my E4200 router. I wish to open my NAT type as currently its moderate on all games.Where the hell is the area to add the port ranges?? Is it even an option on the new connect cloud? If it is, it doesn't make it very easy to find. Would be allot easier if you had a tab/app for "Gaming/Applications" like you did previously.
View 1 Replies View RelatedA while back, I had my own minecraft server running. I had everything working and it was flawless. Then for some reason it just stopped working. I was Unable to open ANY PORTS. I did happen to try 65 - 110 and 254 - 210, as well as 12, 212 and 122. I dopnt know what happened but i have been searching everywhere on the internet (roughly 3 months)
View 1 Replies View RelatedI think i have tried everything i could think of to forward port 5900 with no luck. iIhave e4200. it is for RealVNC application. I followed steps from here: i have windows 7 and nortonn internet security. i disabled the firewall and added a rule to forward port 5900 in windows but did not work either.
View 9 Replies View RelatedI've been configured my device to forward FTP service to my server, however, I can't access this service outside from my network. I used Single Port Forward and not worked, after, I've used Port Range Forwarding starting in 20 to 21 and not work again.I've sniffed my computer and I've found just 3 outsides packages without response.I've tried with directly IP ADDR and DYNDNS ADDR, but neither one or other worked.
View 1 Replies View RelatedI'm trying to set up a minecraft server i have the correct ipv4 adress and port but for some reason its still closed?
View 7 Replies View RelatedIs it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View RelatedInstalled my new EA4500 and trying to access my PC from internet (remote desktop) in order to do so I need to forward the TCP port 3389. In the old web admin page this option was easy to find and change. with the new cloud connect I can't find it. how do Ienable port forwarding on the EA4500?
View 3 Replies View Relatedi am trying to port forward my router so that i can run a minecraft server. When I put in th port number and save the changes, it brings me to a screen that says my changes have been saved yet when i go back to the page they haven't. I have tried deleting the cookies on my browser, using another browser, using another computer, and hard resetting the router for ten seconds. None of this works.
View 2 Replies View RelatedI have unchecked 'Block Anonymous Internet Requests” but then also I am not able to forward ports like 80 and port 443.
View 1 Replies View Relatedi Have a router called Linksys BEFSR41v3 i need to port forward a port but it just wont open i loggerd in on my router using 192.168.1.1 after i click applications & gaming started the port on 100 and ended on 100 used ipconfig in cmd to find me ipv4 adres and putted in ip adress box also both protocol are on and i clicked the enabled function also i tried also got a static ip i used canyouseeme.org to cheak if my port is open it still says its not open.
View 9 Replies View RelatedI attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies View RelatedBEFSR81 will not save port forward info. I am trying to setup port forwarding for xbox (53, 80, 88, 1863, 3074), I click on enable to the far right and then click save at the bottom. It says settings are succeful, will return in 5 seconds. When it returns everything is zeroed out.
View 3 Replies View RelatedRegion : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
I Just bought this Linksys Modem/Router and i still can´t believe that my cheap dlink DIR600 or my OLD SAGEMCOM can set IP to all my machines but this WAG120N cant!and Worse, how will i set port forward if i don't know which IP the machine will get?is there any firmware or MAGIC ??
View 4 Replies View RelatedRegion : Ireland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Smart
I have
A TP-Link TD-8817 Modem with IP Address 192.168.1.1
A TP-Link TL-WDR-3600 Router with IP Address 192.168.0.1
A PC with IP Address 192.168.0.100
I figured out that I can only enter an IP Address with the range 192.168.1.* when port forwarding on the modem, ie I cant enter 192.168.0.100 for the PC.Is there any way of Port Forwarding to the PC?
I have a westell 7500 with fairpoint service hooked up to my DSL line. I have disabled woreless on the westell. I then have a linksys e-1000 connected to the westell 7500. I have one wired computer on that network, my imac/game server, my main PC, my wii and an ipod touch connected connected to the linksys e-1000 wirelessly. I want to forward port 25565 through these routers to my imac. How can I do this? I have tried portforward.com, and a million other things.
View 2 Replies View Relateddhcp setting and port forward
View 3 Replies View RelatedI am trying to forward a port so i can connect to my computer because i want to stream a radio station from computer to my phone.I'm trying to forward port 88 on my Linksys WRT54G Version 6.I tried that but Boardwave audio streaming server still says it's not open!Here are some pictures: I'm using Windows XP Professional 32-Bit
Eset AntiVirus
and using Windows firewall
over my port forward GUI in my new linksys x3000. When I try to save any new port forward rules (new or using predefined), the setting are not saved when I get back to the configuration screen again. Nothing seems to get configured.
Have just uppgraded firmware to v1.0.01, but no difference.
Can switch do a port forward without a router just plane switch to port forward to another network crossing the internet.
View 1 Replies View Related[URL]I want to port forward so my family (not in my home) can play Minecraft on my server. What values should I type?
View 1 Replies View Relatedsetup an external hard drive with music on on the usb port on my EA3500 and actvated ftp but I cant access it from the net.
View 1 Replies View RelatedFor hours i tried to find info online of how to access QoS on EA3500 router. I cannot find it on the cisco connect cloud page.
View 1 Replies View RelatedSystem:
HP Pavilion dv7-6135dx Ent Pc Win7 Home Prem 64
Motorola Surfboard Modem
Linksys EA3500 Router
Netgear 10/100 24 port switch
my wife bought me this EA3500 for Father's Day this year. It's only been hooked up for a couple of weeks (we were in the middle of a move during Father's Day), but now I have no wifi on either band. My wife can no longer connect to it either. We have tried completely resetting it, we have reset the modem, the switch, laptops, everything. Still no wifi. It worked out of the box, but now we have nothing. Does HP needs a certain type of driver? Our iPhones show connected and surf the brower's and FB app with no issues while in wifi mode, but then again, I can pull the ethernet from the internet port and the phone's still show connected (good job, iOS).Cable from main splitter runs to basement where the modem is located. Modem ethernet feed up a wall to a wall plate where the router is. Router then feeds back to the switch. The switch then sends the IP throughout the house for the LAN lines, and the EA3500 feeds all of the wireless devices (used to). So, Cable box, modem, router, switch. Router is currently good for LAN only. I am connected to it via LAN right now, 2 feet from my laptop.
In connections:IPv4/IPv6 both "No Internet Access" (for IPv4, if you change a setting in the setup, it becomes "Internet Access" for about 3 seconds.)Media State: EnabledSpeed: Alternates between 72Mbps and 144Mbps
In my home network, I have a Synology. It has 10.0.123.123 as local IP address on my local network and it can be accessed by internet with the dynamic domain name.So when I'm home, I have to use 10.0.123.123 to access it, and when I'm away, I have to use trucmuche.diskstation.me.Would it be possible to configure the EA3500 to redirect the domain name "trucmuche.diskstation.me" to 10.0.123.123 when I use the domain name inside my home ?A friend told me that I had to configure "loopback" but I don't know how..
View 3 Replies View RelatedI have a belkin f7d4302 v1 and I can't get it to forward my ports.
View 6 Replies View Related